Table of Contents
Advertisement
en-us Basic Operation
Setting the temperature unit
Requirement: The display shows the possible units °C
and °F. The unit °C is preset.
Turn the rotary selector to set the required unit.
1.
Press
to confirm.
2.
Ending initial use
Requirement: The display shows "Initial use complete".
Press
.
▶
The appliance switches to standby mode.
a
The display shows the standby screen.
a
The appliance is ready to use.
a
Cleaning the door pane
Note: To ensure tightness, the door seal is lubricated at
the factory. Residue may remain on the door pane.
Before using for the first time, clean the door pane with
▶
glass cleaner and a window cloth or a microfiber cloth.
Do not use a glass scraper.
Cleaning the accessories
Before first use, clean the accessories thoroughly using
▶
hot soapy water and a soft cloth.
Heating up the appliance
Ensure that there is no leftover packaging in the oven
1.
cavity.
Remove any accessories from the oven cavity.
2.
To eliminate the new-appliance smell, heat up the
3.
empty appliance with the door closed.
The ideal setting for heating is
hour.
7 Basic Operation
Basic Operation
Basic Operation
7.1 Activating the appliance
To exit standby mode, open the door and turn the func-
1.
tion selector or touch a control panel.
Set the required function.
2.
Note: The appliance rinses automatically before each
cooking process if it has not been operated for more than
100 hours.
The appliance rinses automatically after every cooking
process.
7.2 Opening the appliance door
Press .
1.
The appliance opens the appliance door.
a
Use the recessed grip on the side of the oven to open
2.
the appliance door fully.
If the childproof lock is activated, press and hold
few seconds until the appliance opens the door.
16
and 200 °C for one
for a
7.3 Switching on the appliance
Use the function selector to set the required type of
1.
heating.
The display shows the selected type of heating and the
a
suggested temperature.
If required, use the rotary selector to set the desired
2.
temperature.
The display shows the heating symbol
a
The bar shows the current pre-heat status.
a
Once the appliance reaches the set temperature, a sig-
a
nal tone sounds and the heating symbol goes out
Note: If you select a different type of heating, the tempera-
ture that has been set is retained.
The display only shows the suggested temperature once
the appliance has been switched on.
7.4 Switching off the appliance
Turn the function selector to .
▶
Depending on the type of heating, you may hear an au-
tomatic rinse cycle running.
7.5 Steam injection
During steam injection, the appliance injects steam into
the oven cavity. This enables you to bake food such as
bread and bread rolls with sufficient moisture. It also gives
yeast-risen baked goods a smooth, shiny crust.
Steam injection only works with the following types of
heating:
Hot air + 30% humidity
¡
Hot air + 0% humidity
¡
Full surface grill + air recirculation
¡
Starting steam injection
Press
.
▶
After a short time, the appliance injects steam into the
a
oven cavity.
Steam is injected for approximately 5 minutes.
a
Canceling steam injection
Press
.
▶
7.6 Steam removal
During the steam removal process, the appliance intro-
duces cold water into the oven cavity. The steam con-
denses on the oven cavity wall and the oven cavity cools
down.
If you open the appliance door after steam removal, only a
little steam escapes.
WARNING
Hot water may drip down from the appliance door.
Wait until the water on the appliance door has cooled
▶
down.
Steam removal only works with the following types of
heating and if the temperature in the oven cavity is below
270 °C (130 °C):
Hot air + 100% humidity
¡
Hot air + 80% humidity
¡
Hot air + 60% humidity
¡
.
.
Advertisement
Table of Contents
