Table of Contents
Advertisement
RD-7505(A)_ENG_101115_RD-7505(A)_ENG 2010-11-16 오전 10:36 페이지 42
SETTING THE SPEAKER / ROOM EQ
• After you have installed this receiver and connected all the components, you should adjust the speaker settings for the
optimum sound acoustics according to your environment and speaker layout.
• Even when you change speakers, speaker positions, or the layout of your listening environment, you should adjust the
speaker settings, too.
• When performing the AUTO SETUP procedure, you need not perform the CONFIGURATION, DISTANCE and CH LEVEL
setup procedures.
However, you should set the CROSSOVER manually when speakers are set to "SMALL".
SPK / EQ
• AUTO SET(AUTO SETUP) : To set the speaker setup and channel level setup automatically.
• ROOM EQ : To turn on or off the room EQ.
• CONFIG (CONFIGURATION) : To select the sizes of the speakers that are connected.
• X-OVER (CROSSOVER) : To select the desired crossover frequency.
• DISTANCE: To enter the distance between the listening position and each speaker to set the delay time automatically for
optimum surround playback.
• RETURN : To return to the previous menu.
When selecting the AUTO SETUP
• Auto Setup lets you avoid troublesome listening-based speaker setup and achieve good surround sound. Auto Setup has the
feature that provides the optimum listening environment at the listening position in your room.
You should connect the supplied microphone to the SETUP MIC jack so that this receiver can analyze the information from a
series of test tones emitted from speakers at main listening position and can adjust the configuration, distance, sound level
and frequency response of each speaker automatically.
• If you want to personalize your speaker setup and channel level setup by making the settings manually, perform the "When
selecting the CONFIGURATION" on page 45, "When selecting the CROSSOVER" on page 46, "When selecting the
DISTANCE" on page 47 and "SETTING THE CH LEVEL" on page 48.
• After the auto setup has been completed, set the room EQ as desired. (For details, refer to "When selecting the ROOM EQ"
on page 44.)
■Preparations
①. Check that the speakers are securely connected to this receiver.
• If your subwoofer has adjustable volume and crossover frequency, set the volume halfway and set the crossover
frequency to the maximum or the low pass filter off.
②. Connect the supplied microphone to the SETUP MIC jack on the front panel.(For details, refer to "SETUP MIC JACK" on
page 14.)
■Notes :
• Because the microphone for Auto Setup is designed for use with this receiver, to use the auto setup function, do not use a
microphone other than the one supplied with this receiver.
• After you have completed the auto setup procedure, disconnect the microphone.
All manuals and user guides at all-guides.com
AUTO SET
ROOM EQ
MODE : OFF / ON
RETURN
F : LARGE / SMALL
CONFIG
C : LARGE / SMALL / NO
S : LARGE / SMALL / NO
SB : L x 2 / L x 1 / S x 2 / S x 1 / NO
SW : YES / NO
RETURN
X-OVER
FC : 30 / 50 / 80 / 100 / 150 / 200
RETURN
UNIT : FT
DISTANCE
RETURN
/ M
L : 10.0 FT / 0.5 ~ 30.0
C : 10.0 FT / 0.5 ~ 30.0
R : 10.0 FT / 0.5 ~ 30.0
SR : 10.0 FT / 0.5 ~ 30.0
SBR : 10.0 FT / 0.5 ~ 30.0
SBL : 10.0 FT / 0.5 ~ 30.0
SL : 10.0 FT / 0.5 ~ 30.0
SW : 10.0 FT / 0.5 ~ 30.0
RETURN
42
L : 3.0 M / 0.1 ~ 9.0
C : 3.0 M / 0.1 ~ 9.0
R : 3.0 M / 0.1 ~ 9.0
SR : 3.0 M / 0.1 ~ 9.0
SBR : 3.0 M / 0.1 ~ 9.0
SBL : 3.0 M / 0.1 ~ 9.0
SL : 3.0 M / 0.1 ~ 9.0
SW : 3.0 M / 0.1 ~ 9.0
RETURN
Advertisement
Table of Contents
