Table of Contents
Advertisement
F. Brand/Dealer Programming Procedure
This procedure allows the dealer to select the brand input
and dealer information for the consumer's use.
The contact information will be accessible to the consumer
through the "Dealer Info" screen on the secondary menu.
It is also displayed automatically in the event of an issue
with the appliance or as a maintenance reminder.
To access these selections and program your contact
information, please follow these steps.
1. Insert batteries into the IFT-RC400. Wait for a beep to
confirm the remote is on.
2. Locate the programming hole on the back side of the
remote. It is marked as "P" on the right side above the
battery cover as shown in Figure 5.
3. Using a paper clip or similar item, press and release
the programming button. This sequence must be done
while the screen is illuminated.
4. Select your choice of product brand from the list on the
IFT-RC400 screen. See Figure 7.
5. Enter the name of the dealer or service company that
will service this customer by entering the name on the
screen.
6. Enter the telephone number that the customer will use
to contact the service company or dealer.
7. A "splash" screen will appear showing the brand you
selected. "MAIN MENU" will appear next, indicating
that the programming process is complete.
Note: The screen will time out after 7 seconds if a selection
is not made. If this occurs, return to step 2 to access the
selections and continue the programming process.
Figure 7 IFT-RC400 Branding Screen
Hearth & Home Technologies • IFT-RC400 & IFT-ACM Installation Instructions • 2326-982 Rev. Q • 4/21
G. Pairing the IFT-RC400 to the Electronic Con-
trol Module (IFT-ECM)
Note: The display will remain illuminated if you hold a
finger on the screen. When you are ready to
make your next selection, you must remove your
finger and then continue with your next selection.
CAUTION! Risk of Burns! DO NOT program the IFT
Remote Controls to the IFT-ECM when flame or cold
climate function is on or when appliance is hot.
• If adding a new IFT-RC400 to the appliance, follow the
steps in Section F.a.
• If IFT-RC400 is currently paired to IFT-ECM, and add-
ing ACM or other optional accessory feature(s), follow
the steps in Section F.b.
Note: If additional components are added such
as blowers, lights or Power Vent after initial
pairing, the pairing process must be repeated
again to detect additional components.
a. Pairing new IFT-RC400 to Electronic
Control Module (IFT-ECM)
1. On the IFT-ECM, move the ON/OFF/REMOTE switch to
the REMOTE position. The green LED will blink three
times. A few seconds later, an audible "beep" will occur
to indicate that the system is ready.
Note: If the green LED continues to blink slowly (system
is searching for a clear channel), wait until it stops before
proceeding to step 2.
2. Locate the pairing hole on the IFT-ECM. See Figure 9.
Using a paper clip or similar item, press and release
the pairing button. The IFT-ECM will "beep" once and
the green LED will blink for 14 seconds. During the 14
seconds, it is normal for accessories such as lights or
fan to energize momentarily.
While the green LED on the IFT-ECM is blinking, tap anywhere
on the gray indicator bar located at the top of the IFT-RC400
screen. Tap on the pairing function as shown in Figure 10. If
the IFT-RC400 has been paired successfully to the IFT-ECM,
a double audible 'beep" will be heard from the IFT-ECM..
3. If the pairing is unsuccessful, repeat steps 1 & 2.
Note: If additional components are added such
as blowers, lights or Power Vent after initial
pairing, the pairing process must be repeated
again to detect additional components.
NOTICE: Only one IFT-RC400 remote control and one
IFT-RC150 wireless wall switch can be programmed into
an IFT-ECM. To program both an IFT-RC400 and an IFT-
RC150 to an IFT-ECM, repeat the same steps separately
for the IFT-RC400 and the IFT-RC150.
4
Advertisement
Table of Contents
Troubleshooting
