Table of Contents
Advertisement
Quick Links
IntelliFire Plus™ Multifunction Remote Control Systems
Hearth & Home Technologies disclaims any responsibility for,
and the warranty will be voided by, the following actions:
• Installation and use of any damaged system component.
• Modifi cation of the system component.
• Installation other than as instructed by Hearth & Home
Technologies.
• Installation and/or use of any component part not approved
by Hearth & Home Technologies.
Any such action may cause a fi re hazard.
• Read, understand and follow these instructions for safe
installation and operation.
Fireplace Specifi c Information
Standard fi replace features vary. Consult the installation
manual for available options.
The included AUX300CE receiver provides additional fea-
tures: Fan control and two Aux functions.
The REM300-HNG-AU remote control system functions
include: On/Off, Thermostat Mode, Timer Countdown,
and Flame Adjustment (for fi replaces with variable fl ame).
Kit Contents
REM300-HNG-AU
• REM300-HNG-AU Transmitter
• AAA Batteries (3)
• Wall Holder
• Drywall Anchor (2)
• Screws (2)
Hearth & Home Technologies • RC300AU Multifunction Remote Control • 2166-394 Rev. D • 8/11
REM300-HNG-AU
Installation & Operating Instructions
Introduction
The RC300AU multifunctional remote control is de-
signed to control pilot light, fl ame height, blower speed,
and up to two 220-240VAC auxiliary functions on your
gas fi replace. The RC300AU is equipped with thermo-
stat functions which can automatically control the tem-
perature in the room in which it is installed. The control
is only for use with the Hearth & Home Technologies
IntelliFire Plus™ system (IPI). The AUX300CE module
is rated for 220-240VAC, 50-60 Hz, and is required for
operation of this remote control device.
Installation Precautions
The installation of this remote control must be performed
by a qualifi ed service technician. This remote control is
tested and safe when installed in accordance with this in-
stallation manual. Do not install any components that may
be damaged.
Do not modify, disassemble, or substitute any of the com-
ponents included with this kit. Installation of this unit must
be done by a qualifi ed service technician.
Placement of this remote control may affect performance.
An assessment of the space should be done prior to in-
stallation for optimum performance.
Determine Location
Determine the location for the remote control. The selected
location should be in the same space as the gas fi replace.
Never place this unit in a separate room. The remote control
must be placed within 30 feet (9.14 m) of the fi replace but
should not be exposed to extreme heat.
The RC300AU is approved for interior installation and
should not be used in exterior applications.
• Keep remote control out of reach of children.
1
Advertisement
Table of Contents
Related Manuals for Hearth and Home Technologies IntelliFire Plus REM300-HNG-AU
Summary of Contents for Hearth and Home Technologies IntelliFire Plus REM300-HNG-AU
- Page 1 REM300-HNG-AU IntelliFire Plus™ Multifunction Remote Control Systems Installation & Operating Instructions Introduction Hearth & Home Technologies disclaims any responsibility for, The RC300AU multifunctional remote control is de- and the warranty will be voided by, the following actions: signed to control pilot light, fl ame height, blower speed, •...
-
Page 2: Fcc Requirements
FCC Requirements Installation of Remote Control Housing WARNING! Risk of Fire! Changes or modifi cations to CAUTION! Risk of Fire! DO NOT install damaged or this unit not expressly approved by the party responsible modifi ed components Warranty will be voided if damaged for compliance could void the user’s authority to operate or modifi... - Page 3 Programming the RC300AU to the Control Module CAUTION! Risk of burns! DO NOT program the remote control to the control module when fi replace is hot. • Verify the ON/OFF/REMOTE switch is in the REMOTE position. Green LED light will blink three times and wall switch will beep once 5 seconds later when ready.
- Page 4 240V FAN IGNITOR FLAME SENSE 6V DC SUPPLY TRANSFORMER WHITE CONTROL MODULE ORANGE AUX300CE MODULE AUX 1 AUX 2 TO JUNCTION BOX 220-240 VAC 8K1 WIRE HARNESS TO OPTIONAL COMPONENTS OPTIONAL ON/OFF WALL SWITCH GREEN ORANGE (MAIN) BLACK (PILOT) BATTERY PACK BROWN 6V DC (AA X 4) GROUND...
-
Page 5: Display Screen
Display Screen Idle When Remote is in ON Mode The remote control will go into an idle mode if no but- THERMOSTAT DESIRED tons are pressed within 5 seconds. Press any button to FIREPLACE STATUS TEMP SETTING resume full functionality. In idle mode only active func- tions will show on the screen. - Page 6 About ON Mode Adjusting Fan Speed • All functions can be accessed when the remote control • Press the MENU button to activate the menu. is in the ON mode. • Using the UP and DOWN arrows highlight the FAN icon •...
- Page 7 Adjusting Thermostat Power Outage • Press the MENU button to activate the menu. • If fi replace battery backup system IS installed at time of power outage, fi replace operation will not be interrupted. • Using the UP and DOWN arrows highlight the THERMO icon and press SELECT.
-
Page 8: Frequently Asked Questions/Troubleshooting
Frequently Asked Questions/Troubleshooting Symptom Possible Cause Corrective Action Batteries Verify batteries are functional and installed correctly. Remote control is in Child Disengage Child Lock mode. Remote control will not transmit Lock mode Buttons not being pressed Press button fi rmly for one to two seconds to ensure transmis- fi...