Table of Contents
Advertisement
Quick Links
IntelliFire Plus™ Multifunction Remote Control
Hearth & Home Technologies disclaims any responsibility
for, and the warranty will be voided by, the following actions:
• Installation and use of any damaged system component.
• Modification of the system component.
• Installation other than as instructed by Hearth & Home
Technologies.
• Installation and/or use of any component part not approved
by Hearth & Home Technologies.
Any such action may cause a fire hazard.
• Read, understand and follow these instructions for safe
installation and operation.
Introduction
The RC300 multifunctional remote control is designed
to control flame height on your gas appliance. The
RC300 is equipped with thermostat functions which
can automatically control the temperature in the room
in which it is installed. The control is only for use with
the Hearth & Home Technologies IntelliFire Plus™ sys-
tem (IPI).
Installation Precautions
This remote control is tested and safe when installed in
accordance with this installation manual. Do not install
any components that may be damaged.
Do not modify, disassemble, or substitute any of the com-
ponents included with this kit. Installation of this remote
must be done by a qualified service technician.
Placement of this remote control may affect performance.
An assessment of the space should be done prior to in-
stallation for optimum performance.
Determine Location
Determine the location for the remote control. The selected
location should be in the same space as the gas appliance.
Never place this remote in a separate room. The remote
control must be placed within 30 feet (9.14 m) of the appli-
ance but should not be exposed to extreme heat.
The RC300 is approved for interior installation and should
not be used in exterior applications.
• Keep remote control out of reach of children.
Hearth & Home Technologies • RC300-MON-VFL Multifunction Remote Control • 4018-900 Rev. B • 02/21
RC300-MON-VFL
Installation & Operating Instructions
FCC Requirements
WARNING! Risk of Fire! Changes or modifications to
this remote not expressly approved by the party respon-
sible for compliance could void the user's authority to op-
erate the equipment.
Note: This equipment has been tested and found to
comply with the limits for a Class B digital device, pur-
suant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in ac-
cordance with the instructions, may cause harmful in-
terference to radio communications. However, there is
no guarantee that interference will not occur in a partic-
ular installation. If this equipment does cause harmful
interference to radio or television reception, which can
be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit dif-
ferent from that to which the receiver is connected.
• Contact the dealer or an experienced radio TV techni-
cian for help.
Canadian Equipment Requirements
This digital apparatus does not exceed the (Class A/ Class
B) limits for radio noise emissions from digital apparatus
set out in the Radio Interference Regulations of the Cana-
dian Department of Communications. Le present appareil
numerique n'emet pas de bruits radioelectriques depas-
sant les limites applicables aux appareils numeriques (de
la class A/de la class B) prescrites dans le Reglement sur
le brouillage radioelectrique edicte par le ministere des
Communications du Canada.
This device complies with RSS-210 of Industry and Sci-
ence Canada. Operation is subject to the following two
conditions: (1) this device may not cause interference, and
(2) this device must accept any interference, including in-
terference that may cause undesired operation of the de-
vice.
1
Advertisement
Table of Contents
Related Manuals for Hearth and Home Technologies IntelliFire Plus RC300-MON-VFL
Summary of Contents for Hearth and Home Technologies IntelliFire Plus RC300-MON-VFL
- Page 1 RC300-MON-VFL IntelliFire Plus™ Multifunction Remote Control Installation & Operating Instructions FCC Requirements Hearth & Home Technologies disclaims any responsibility WARNING! Risk of Fire! Changes or modifications to for, and the warranty will be voided by, the following actions: this remote not expressly approved by the party respon- •...
-
Page 2: Changing Temperature Scale
Changing Temperature Scale 4. Place remote control inside housing. See Figure 3. To change the temperature display between Celsius and Fahrenheit, remove the battery cover from the back of the remote control and slide the switch to your desired tem- perature scale (see Figure 1). - Page 3 Programming the RC300 to the Control Module CAUTION! Risk of burns! DO NOT program the remote control to the control module when appliance is hot. • Verify the ON/OFF/REMOTE switch is in the REMOTE position. Green LED light will blink three times and control module will beep once 5 seconds later when ready.
- Page 4 PILOT THERMOCOUPLE MODULE RC300 4.5V DC (AAA X 3) Thermocouple Module Wire Assembly CONTROL MODULE FLAME MODULATION BATTERY PACK 6V DC Figure 6. RC300 Wiring Diagram Hearth & Home Technologies • RC300-MON-VFL Multifunction Remote Control • 4018-900 Rev. B • 02/21...
-
Page 5: Display Screen
Display Screen Idle When Remote is in ON Mode The remote control will go into an idle mode if no but- THERMOSTAT DESIRED tons are pressed within 5 seconds. Press any button to APPLIANCE STATUS TEMP SETTING resume full functionality. In idle mode, only active func- tions will show on the screen. -
Page 6: Turning On The Appliance
About ON Mode Adjusting Thermostat • Press the MENU button to activate the menu. • All functions can be accessed when the remote control is in the ON mode. • Using the UP and DOWN arrows highlight the THERMO • Only active functions will be displayed when the remote icon and press SELECT. -
Page 7: Setting The Child Lock
Setting the Child Lock • Press and hold the MENU and UP arrow buttons simul- taneously for 4 seconds to enable or disable the child lock feature. NOTICE: No functions will be usable until child lock feature is disabled. Power Outage •... -
Page 8: Frequently Asked Questions/Troubleshooting
Frequently Asked Questions/Troubleshooting Symptom Possible Cause Corrective Action Batteries Verify batteries are functional and installed correctly. Remote control is in Child Disengage Child Lock mode. Remote control will not transmit Lock mode Buttons not being pressed Press button firmly for one to two seconds to ensure transmis- firmly sion to module. Control module is not in Ensure module switch is set to REMOTE.