1. Manuals
  2. Brands
  3. Furuno Manuals
  4. Sonar
  5. CSH-83
  6. Installation manual

Furuno CSH-83 Installation Manual

Color scanning sonar
Hide thumbs Also See for CSH-83:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Operator's Manual
Back
COLOR SCANNING SONAR
CSH-83/84
MODEL

Advertisement

Table of Contents
loading

Related Manuals for Furuno CSH-83

Summary of Contents for Furuno CSH-83

  • Page 1 Back COLOR SCANNING SONAR CSH-83/84 MODEL...
  • Page 2 Printed in Japan All rights reserved. All rights reserved. Pub. No. IME-13090-H3 Pub. No. IME-13090-H3 ( ( TATA TATA ) ) CSH-83/84 CSH-83/84 The paper used in this manual is elemental chlorine free. FURUNO Authorized Distributor/Dealer FURUNO Authorized Distributor/Dealer FIRST EDITION : FIRST EDITION : OCT.
  • Page 3 The installer of the equipment is solely responsible for the proper installation of the equipment. FURUNO will assume no responsibility for any damage associated with improper installation. WARNING Install the specified transducer tank in accordance with the installation instructions.

  • Page 4: Table Of Contents

    TABLE OF CONTENTS 1. SYSTEM CONFIGURATION ... 2. EQUIPMENT LISTS ... 3. MOUNTING THE EQUIPMENT 3.1 Mounting the Hull Unit and Receiver Unit ... 3-1 3.2 Mounting the Display Unit and Sub-Display Unit (option) ...3-7 3.3 Mounting the Transmitter Unit ...3-8 3.4 Mounting the Power Unit ...3-8 3.5 Mounting the Interface Unit ...3-8 3.6 Mounting the FNZ Joint Box ...
  • Page 5 7.3 DIP Switch Setting in the Display Unit... 7-3 7.4 Setting and Adjustment in the Interface Unit... 7-5 8. WHEN SHIP’S MAINS IS 24 VDC ... 8-1 9. PROCESSOR UNIT CSH-835 (BLACKBOX TYPE FOR CSH-83)... 9-1 SPARE PARTS, INSTALLATION MATERIALS, ACCESSORIES...A-1 OUTLINE DRAWINGS... D-1...
  • Page 6 This page is intentionally left blank.

  • Page 7: System Configuration

    CSH-835 INTERFACE UNIT CS-120A RECEIVER UNIT CSH-820 HULL UNIT CSH-81080 (800 mm stroke) CSH-81120 (1200 mm stroke) SUB DISPLAY * CSH-236 * : CSH-83 110/115/220/230 VAC, STEP-DOWN 1 , 50/60 Hz TRANSFORMER PT-400 SPEED LOG AD CONVERTER NAVIGATOR CURRENT INDICATOR...

  • Page 8: Equipment Lists

    CP10-06600 Accessories FP10-02400 FP10-01900 FP10-03000 Spare Parts SP10-02000 SP10-03600 Type Select For CSH-83 For CSH-84 Blackbox type for CSH-83 w/hull unit stroke 800mm stroke 1200mm 1 set CP10-03010 6 pair cable 1 set CP10-03610 6 pair cable 1 set CP10-06610...
  • Page 9 Code No. Remarks CSH-83 only 200-230 VAC 000-101-006 Specify length 000-101-007 Specify length 000-101-008 Specify length 006-990-040 For CSH-116 See page 8-1. 000-069-996 For extending transceiver cable 000-068-861 006-904-340 006-027-830 For CSH-83 006-997-710 For CSH-83 000-908-560 For CSH-84 006-998-620 006-998-650 Remarks...

  • Page 10: Mounting The Equipment

    • Secure sufficient space for wiring and maintenance. Refer to the hull unit outline drawing for recommended wiring and maintenance space. • If the ambient temperature of the hull unit is below 0 C, provide the sonar compartment with a heater to keep the temperature above 0 C.
  • Page 11 Heater Heat insulator Figure 3-2 Typical sonar compartment...
  • Page 12 Shortening the retraction tank The retraction tank is 900 mm in length when supplied. Shorten the tank as necessary so that the transducer is placed well below the keel when it is lowered. The following table provides guide- lines for shortening the tank. Refer also to the retraction tank installation drawing at the back of this manual.
  • Page 13 Remarks on installation of retraction tank • If possible, the installation location should be of double bottom structure. • If possible, install the tank on the keel, where the tank can be most firmly fixed. • Install the reinforcement rib as near as possible to the top of the retraction tank, allowing space for tightening bolts and nuts.
  • Page 14 Installing hull unit on retraction tank After welding the retraction tank and allowing sufficient time for cooling, install the hull unit as follows: 1. Clean the O-ring and O-ring groove and coat them with a slight amount of grease. Place the O-ring in position on the tank flange.
  • Page 15 Installing stays (anti-vibration measure) Install stays from the top of the hull unit to the ship’s hull. The stays should be angle iron with a size of 75 9 mm or more and at least two pieces should be used; one each to ship’s bow and stern directions.

  • Page 16: Mounting The Display Unit And Sub-Display Unit (Option)

    3.2 Mounting the Display Unit and Sub-Display Unit (option) The display unit and sub-display unit are designed for tabletop mounting. When selecting a mounting location, consider the following conditions: • Place where operating personnel are able to control the unit easily while observing the fish- ing ground or the area surrounding the vessel.

  • Page 17: Mounting The Transmitter Unit

    3.3 Mounting the Transmitter Unit The transmitter unit can be mounted with or without mounting legs. For use without mounting legs remove them and use inside mounting holes. Reinforce the transmitter unit against vibration by stays extending from the eyebolts on the top of the unit.

  • Page 18: Grounding The Equipment

    3.7 Grounding the Equipment Ground all units with a suitable copper strap or ground wire. The location of the ground termi- nal on each unit is shown below. DISPLAY UNIT RECEIVER UNIT Figure 3-12 Location of ground terminals on equipment CAUTION Ground the equipment to prevent electrical shock and...

  • Page 19: Wiring

    4. WIRING This chapter provides the information necessary for wiring the CSH-83/84. Wire the equipment referring to the drawings shown in the table below. Display Unit CN-A5 Interface Unit J201 4.1 Cable Configuration Figure 4-1 Cable configuration...

  • Page 20: How To Use The Crimping Tool And Pin Extractor

    4.2 How to Use the Crimping Tool and Pin Extractor A crimping tool is necessary for connection of wires to the contact pins of the 38P connector. The pin extractor removes the contact pin from the connector body. This paragraph describes how to crimp and extract a contact pin.

  • Page 21: Location Of Connectors

    4.3 Location of Connectors 10S1277,...

  • Page 22: Cable Fabrication And Connector Assembling In Display And Interface Units

    4.4 Cable Fabrication and Connector Assembling in Display and Interface Units Assembling 38P connector (CN-A1, CN-A5, J201) Fabrication of cable 10S1258-1 Shield Vinyl sheath Core Expose cores, and then wind shield around the armor. Figure 4-4 Fabrication of cable 10S1258-1 Assembling the 38P connector Shorten unused wires and wrap their ends with vinyl tape to prevent short circuit.
  • Page 23 Positioning guide pins The guide pins of the connector identify the mating receptacle. Position them as shown in the table below. Table 4-1 Connectors CN-A1, CN-A5, J201 and guide pins Connector Guide Pin Guide Pin A (Large) Guide Pin B (Small) Clamping the cable Fix the cable in the clamp where shield is folded back onto the armor.
  • Page 24 Assembling BNC connector (CN-A7, CN-A8, CN-A9, CN-A10, CN-A11, CN-A12) Housing Clamp Center pin Shield Figure 4-8 Assembling BNC connector 1. Remove vinyl sheath of the cable by 15 mm. Washer 2. Pass the cable through the nut, washer, gasket and clamp. Gasket 3.

  • Page 25: Cable Fabrication And Connector Assembling In Power Unit

    4.5 Cable Fabrication and Connector Assembling in Power Unit Assembling 38P connector (CN-E1) Fabrication of cable 10S1260 Shield Vinyl sheath Armor Figure 4-9 Fabrication of cable 10S1260 Assembling the 38P connector 1. Bundle unused wires outside the connector case. 2. Fix the cover 1, noting the cable outgoing direction. 3.
  • Page 26 Positioning guide pins The guide pins of the connector identify the mating receptacle. Position them as shown in the table below. Table 4-2 Guide pins and connector CN-E1 Connector Guide Pin Guide Pin A (Large) Guide Pin B (Small) Clamping the cable Fabrication of cable 10S1259 (connected to terminal board TB-E1) Figure 4-12 Fabrication of cable 10S1259 Fabrication of cable DPYCY-3.5 (connected to terminal board...

  • Page 27: Cable Fabrication And Connector Assembling In Transmitter Unit

    4.6 Cable Fabrication and Connector Assembling in Transmitter Unit Assembling 38P connector (CN-B2, CN-B3, CN-B4) Fabrication of cables 10S1258-1, 10S1260 Shield Vinyl sheath Armor Figure 4-14 Fabrication of cables 10S1258-1, 10S1260 Assembling the 38P connector 1. Bundle unused wires outside the connector case. 2.
  • Page 28 Positioning guide pins Guide pins of the connector are used to identify the mating receptacle. Position them as shown the table below. Table 4-3 Connectors CN-B2, CN-B3, CN-B4 and guide pins Connector Guide Pin Guide Pin A (Large) Guide Pin B (Small) Clamping the cable Fabrication of cable 10S1259 (connected to terminal board TB-B1) Figure 4-17 Fabrication of cable 10S1259...

  • Page 29: Cable Fabrication And Connector Assembling In Hull Unit (Incl. Receiver Unit)

    4.7 Cable Fabrication and Connector Assembling in Hull Unit (incl. receiver unit) Assembling 38P connector (CN-C1, CN-C3, CN-C4) 20P connector (CN-C2) Fabrication of cable for 38P and 20P connectors CN-C1, CN-C3 Shield Vinyl sheath Core Expose cores; wind shield around armor. Figure 4-18 Fabrication of cable for 38P and 20P connectors Assembling the 38P connector 1.
  • Page 30 Positioning guide pins The guide pins of the connector identify the mating receptacle. Position them as shown in the table below. Table 4-4 Connectors CN-C1, CN-C2, CN-C3, CN-C4 and guide pins Connector CN-C1 Guide Pin Guide Pin A (Large) Guide Pin B (Small) Clamping the cable Fabrication of cable 10S1261 (connected to terminal board TB-D1 in raise/lower control box)

  • Page 31: Connection Of Transducer Cables

    Fabrication of cable 10S1259 (connected to terminal board TB-D2 in raise/lower control box) Figure 4-22 Fabrication of cable 10S1259 4.8 Connection of Transducer Cables The transducer cables come with connectors attached. Plug the connectors into the proper re- ceptacles on the receiver unit, referring to the labels on the cables. Transducer cable entrance Lead the cables into the receiver unit and clamp them as shown below.

  • Page 32: Connection Of Interface Unit

    4.9 Connection of Interface Unit CS-120A With connection of navigator, the Interface Unit CS-120A and electronic fishing equipment, the function of the CSH-83/84 series is expanded to include true motion presentation, target lock, echo sounder picture, FNZ marker presentation and digital indication of position, water temperature and depth.
  • Page 33 There are six combinations of CIF/NMEA data input. Combination NMEA port J208 NMEA data NMEA data － NMEA data － － Note: NMEA port and CIF port are not fed a data at the same time. Either CIF current data or NMEA data can be fed to CI/NMEA port.
  • Page 34 Connections for ES picture and FNZ markers To provide echo sounder picture and FNZ markers, connect echo sounder to J203 and net sonde to J202. The signals applied to J202 and J203 are J202: Net sonde signal and trigger signal (keying pulse of echo sounder). A white line signal from an echo sounder may be additionally applied as described on the next page if the digital depth data is not available on J204.
  • Page 35 Connections for digital indication of position, water temperature and depth The data for these readouts are taken from the equipment shown in the table below and input to J208 or J204. Input to J208 if the data is NMEA format, or to J204 if the data is CIF format.
  • Page 36 Assembling 10P and 7P connectors 10P Connector (SRCN6A16-10P) VINYL SHEATH VINYL SHEATH (INNER) (OUTER) SOLDER UNUSED CORES AND EARTH TO BRAIDED SHIELD SOLDERING WIND SHIELDING TAPE VINYL SHEATH ARMOR (OUTER) WIND VINYL TAPE 7P Connector (SRCN6A16-7P) VINYL SHEATH SOLDER UNUSED CORES AND EARTH WIRE TO BRAIDED SHIELD VINYL SHEATH...

  • Page 37: Connection Of Sub-Display Unit (Option)

    One sub-display unit can be connected to three display units. Note: The Sab-Display Unit can be connected to CSH-83 only. Connections Refer to the interconnection diagram on page S-1 and the connector assembling/cable fabrica- tion procedure on page 4-4.

  • Page 38: Connection Of Remote Display Unit (Option)

    Note: The Remote-Display Unit can be connected to CSH-83 only. Connections Refer to interconnection diagram on page S-1 and cable fabrication/connector assembling pro- cedure on page 4-11.

  • Page 39: Synchronizing Transmission With Other Sonars Or Echo Sounders

    Set polarity of the KP on the INIT/SET menu. Set transmission cycle to “0” on data setting window. Refer to the operator’s manual for further details. b) For voltage driven KP Display unit CN-A6 EXT KP H <MM< Sonar GND <TT< b) Voltage driven KP output Display unit Sonar INT KP H <KK<...

  • Page 40: Interlocking Operation With Other Sonars

    Set ID code with DIP switches #1 thru #3 on the display unit. Any code is acceptable, provided that it is not the same as that set on the other sonar. For how to access the DIP switches see page 7-3.
  • Page 41 Connections for interlocking remote control A single remote control box can control three display units. Connect it to the display units as shown below. REMOTE CONTROL CONE Board on DISPLAY UNIT 1 Figure 4-36 Connections for remote control of multiple display units Connect same pin numbers.

  • Page 42: Changing Power Specifications

    5. CHANGING POWER SPECIFICATIONS The display unit is set at the factory for connection to ship’s mains of 100 VAC. To power it by 110 VAC or 220 VAC, use step-down transformer PT-400, change the transformer taps on the power unit as below and connect the ship’s mains directly. F Photo No.1747 POWER UNIT Figure 5-1 Changing tap connections on the power unit...

  • Page 43: Installation Of Frp Retraction Tank

    • Use only the tank supplied. • Follow the instructions in this chapter. • If the owner of the equipment elects to use a shipyard-prepared FRP tank, FURUNO will assume no responsibility for any damage caused by water leakage. If the shipyard supplies the FRP tank, do the following: •...
  • Page 44 Waterproofing gasket Figure 6-2 Laying the waterproofing gasket on the tank flange 3. Orient the bow mark (arrow) on the hull unit flange toward ship’s bow. (If the mark cannot be perfectly oriented toward ship’s bow adjust heading after installation as shown in the next chapter.) Figure 6-3 Orienting hull unit flange toward ship’s bow 4.
  • Page 45 6. Set the hull unit on top of the retraction tank. Pass flat washer onto hex bolt and insert them in stud bolt hole from the top of the hull unit flange. At the retraction tank, fasten the bolt with insulation gasket, flat washer, spring washer and nut, in the order shown in the figure below.

  • Page 46: Adjustment And Check

    7. ADJUSTMENT AND CHECK 7.1 Hull Unit Check 1. Press the ON switch to turn on the equipment. Con- firm that the lamps above the ON and c switches light. 2. Confirm that the 5V and UP lamps on the raise/ lower control box are lit.

  • Page 47: Heading Adjustment

    11. Press the d switch. Confirm that the lamp above the switch blinks while the transducer is being lowered, a short beep sounds when the mid limit switch kicks, and the lamp lights when the transducer is fully lowered. 12. Press the c switch. Confirm that the lamp above the switch blinks while the transducer is being raised, a short beep sounds when the mid limit switch kicks, and the lamp lights when the transducer is fully raised.

  • Page 48: Dip Switch Setting In The Display Unit

    INIT SET/TEST MENU Select item with dc[ \ keys and press MENU key. Press END key to close menu. HEADING ADJ 4. Enter heading correction with [ or \, referring to the example in the table below for guidance. 7.3 DIP Switch Setting in the Display Unit Set the DIP switch in display unit, referring to the table shown below.
  • Page 49 DSW Board (10P6722F) Item SW No. ID Code for Set ID code for interlock operation of CSH-23/24/73/83/84 sonar. Interlock Any code is acceptable unless it is used in other interlocked Function sonars. Unit Code CSH-58 (28 kHz) Unit CSH-53 (28 kHz)

  • Page 50: Setting And Adjustment In The Interface Unit

    7.4 Setting and Adjustment of the Interface Unit CS-120A DIP switch setting Navigation data and fishing data input from external equipment can be turned on or off by DIP switches DP-1 and DP-2 on CPU II board 10P6871 in the Interface Unit CS-120A. DP-2 CI/NMEA port Input format Input format...
  • Page 51 Depth data is selected with S5. *: Use this position for white line pulse when the depth data is taken from an echo sounder. However late model FURUNO echo sounders do not output white line pulse. Normally set to ON.
  • Page 52 10 ms after transmission to avoid false depth indication caused by unwanted noise in short ranges. Readjustment of potentiometer R27 is not required as long as CSH-83/84 series indicates the correct depth. If does not, however turn R27 to the right. Adjustment of white line output level (R55) Improper setting of potentiometer R55 causes the seabed line to be painted in deep blue due to the white line pulse.
  • Page 53 Depth priority Depth is set to CIF/NMEA with S5 on the DIP switch DP-1. 1. SD-DPT from NMEA port 2. SD-DPT from CI/NMEA port 3. SD-DBT from NMEA port 4. SD-DBT from CI/NMEA port 5. <57> from CIF port Ship’s movement data priority (data from GPS/DR) Ship’s movement data is set to GPS·DR with S1/S2 on the DIP switch DP-1 1.

  • Page 54: When Ship's Mains Is 24 Vdc

    8. WHEN SHIP’S MAINS IS 24 VDC When the ship’s mains is 24 VDC, use DC/AC inverter unit TR-2435, TR-24100 and current limiter box CSH-1400. (All units are optional supply.) The system diagram and interconnection diagram are as follows. 10S1277,...
  • Page 55 Transmitter Unit Power Unit CSH-880 TB-E1 CN-E1 TB-01 Current Limiter Box CSH-1400 Figure 8-2 Connection with 24 VDC ship’s mains CSH-810 TB-B1 *DPYCY-3.5 *DPYCY-3.5 TR Inverter TR-24100 100 VAC OUTPUT 1 kVA INPUT 24 VDC *DPYCY-5.5 TB-02 Display Unit CSH-830 CSH-8400 CN-A15 100 VAC...

  • Page 56: Processor Unit Csh-835 (Blackbox Type For Csh-83)

    9. PROCESSOR UNIT CSH-835 (BLACKBOX TYPE FOR CSH-83) 9.1 Installing the Unit When selecting a mounting location, consider the following conditions: • Place where operating personnel are able to control the unit easily while observing the fishing ground or the area surrounding the vessel.
  • Page 57 Vertical, TTL level, 60.111 Hz 0.007 Hz, 75 Ω Resolution: VGA, 664 x 481 Mount the monitor in portrait orientation. Note that FURUNO monitor model MU-151C can be used in portrait orientation. 9.3 Connecting cables Fabricate the cables as shown in the section “4.4 Cables Fabrication and Connect Assembling in Display and Interface Units.”...
  • Page 58 Connectors for Monitor There are two kinds of video signal ports: D-sub connector (default) and BNC connectors. • D-sub: Use interconnection cable 3COX-2P-6C (5 m or 10 m) or equivalent commercially available cable. • BNC connector: Use five 75 Ω coaxial cables (shipyard supply). The coaxial cables are preferred in case of longer than 10 m cable run between the processor unit and monitor.
  • Page 59 ＰＡＣＫＩＮＧ ＬＩＳＴ CSH-235/235K/235F/535/585/735/835 N A M E ユニット UNIT 操作制御部 PROCESSOR UNIT 予備品 SPARE PARTS 予備品 SPARE PARTS 工事材料 INSTALLATION MATERIALS 工事材料 INSTALLATION MATERIALS 1.ｺ-ﾄﾞ番号末尾の[**]は、選択品の代表型式/ｺｰﾄﾞを表します。 CODE NUMBER ENDING WITH "**" INDICATES THE CODE NUMBER OF REPRESENTATIVE MATERIAL. （略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.） DESCRIPTION/CODE №...
  • Page 60 SHIP NO. SPARE PARTS LIST FOR ITEM NAME OF OUTLINE PART ﾋｭｰｽﾞ FUSE MFR'S NAME FURUNO ELECTRIC CO.,LTD. （略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.） 006-030-590 CODE NO. SP10-03201 TYPE U S E QUANTITY DWG. NO. WORKING TYPE NO. SPARE FGBO-A 5A AC125V DWG NO.
  • Page 61 工事材料表 INSTALLATION MATERIALS 番 号 名  称 NAME +ﾄﾗｽﾀｯﾋﾟﾝﾈｼﾞ 1種 SELF-TAPPING SCREW ｺﾈｸﾀ(NCS) CONNECTOR(NCS) （略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.） 006-030-600 CODE NO. TYPE CP10-06301 略  図 型名／規格 OUTLINE DESCRIPTIONS 6X20 SUS304 CODE NO. 000-802-084 NCS-253-P CODE NO. 000-506-503 ＦＵＲＵＮＯ ＥＬＥＣＴＲＩＣ ＣＯ ．，ＬＴＤ. 10CJ-X-9401 数量 用途／備考 Q'TY REMARKS 10CJ-X-9401...
  • Page 62 XH.CONNECTOR ASSY. XHｺﾈｸﾀ組品 XH.CONNECTOR ASSY. ﾋｭｰｽﾞ FUSE ｺﾈｸﾀ抜き工具 CONNECTOR PULLER MFR'S NAME MFR'S NAME FURUNO FURUNO ELECTRIC ELECTRIC MFR'S NAME MFR'S NAME FURUNO FURUNO ELECTRIC ELECTRIC （略図の寸法は、参考値です。　DIMENSIONS IN DRAWING FOR REFERENCE ONLY.） （略図の寸法は、参考値です。　DIMENSIONS IN DRAWING FOR REFERENCE ONLY.） （略図の寸法は、参考値です。　DIMENSIONS IN DRAWING FOR REFERENCE ONLY.）...
  • Page 63 XHｺﾈｸﾀ組品 XH.CONNECTOR ASSY. XHｺﾈｸﾀ組品 XH.CONNECTOR ASSY. ｺﾈｸﾀ抜き工具 CONNECTOR PULLER ﾋｭｰｽﾞ FUSE MFR'S NAME FURUNO ELECTRIC CO.,LTD. （略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.） 000-070-211 CODE NO. SP10-03600 TYPE U S E QUANTITY DWG. NO. WORKING SPARE TYPE NO. F-7165 20A...
  • Page 64 工事材料表 工事材料表 工事材料表 工事材料表 INSTALLATION MATERIALS 番 号 名  称 NAME ｺﾈｸﾀ(SRCN) CONNECTOR(SRCN) ｺﾈｸﾀ(8016） CONNECTOR(8016) 貼りﾏｰｸ.J201. STICKER.J201. ｺﾈｸﾀ(54) CONNECTOR(54) ｺﾝﾀｸﾄ ﾋﾟﾝ（8017) CONTACT PIN (8017) ｱｰｽ線組品 GROUNDING WIRE ｺﾈｸﾀ(RM) CONNECTOR(RM) ｺﾈｸﾀ(SRCN） CONNECTOR(SRCN) ｺﾈｸﾀ(SRCN） CONNECTOR(SRCN) ｺﾈｸﾀ(8016） CONNECTOR(8016) （略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.） （略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.）...
  • Page 65 工事材料表 工事材料表 工事材料表 工事材料表 INSTALLATION MATERIALS 番 号 名  称 NAME ｸｰﾗｰﾊﾟﾃ COOLER PUTTY ｲﾗｯｸｽﾁｭｰﾌﾞ(A) INSULATION TUBE(A) ｺﾈｸﾀ(NCS) CONNECTOR ｺﾈｸﾀ(NCS) CONNECTOR(NCS) ｱｰｽ板 COPPER STRAP ｺﾈｸﾀ(8016) CONNECTOR P貼りﾏｰｸ.11. P STICKER.11. ｺﾈｸﾀ(54) CONNECTOR(54) ｺﾝﾀｸﾄ ﾋﾟﾝ（8017) CONTACT PIN (8017) ﾎｰﾙﾌﾟﾗｸﾞ HOLE PLUG （略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.） （略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.）...
  • Page 66 工事材料表 工事材料表 工事材料表 工事材料表 INSTALLATION MATERIALS 番 号 名  称 NAME ｱｰｽ板 COPPER STRAP ｼｰﾙﾄﾞｽﾘｰﾌﾞ SHIELD SLEEVE 圧着端子 CRIMP-ON LUG 圧着端子 CRIMP-ON LUG 圧着端子 CRIMP-ON LUG 貼りﾏｰｸ STICKER ｺﾈｸﾀ(54) CONNECTOR(54) ｺﾝﾀｸﾄ ﾋﾟﾝ（8017) CONTACT PIN (8017) 圧着端子 CRIMP-ON LUG 圧着端子 CRIMP-ON LUG （略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.）...
  • Page 67 工事材料表 工事材料表 工事材料表 工事材料表 INSTALLATION MATERIALS 番 号 名  称 NAME ﾎｰﾙﾌﾟﾗｸﾞ HOLE PLUG ｱｰｽ板 COPPER STRAP 貼りﾏｰｸ.1. STICKER.1. ｺﾈｸﾀ(54) CONNECTOR(54) ｺﾝﾀｸﾄ ﾋﾟﾝ（8017) CONTACT PIN (8017) 圧着端子 CRIMP-ON LUG 圧着端子 CRIMP-ON LUG ﾎｰﾙﾌﾟﾗｸﾞ HOLE PLUG ｱｰｽ板 COPPER STRAP （略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.） （略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.）...
  • Page 68 A-10...
  • Page 69 工事材料表 工事材料表 工事材料表 工事材料表 INSTALLATION MATERIALS 番 号 名  称 NAME ｺﾈｸﾀ(8016） CONNECTOR(8016) 貼りﾏｰｸ.J201. STICKER.J201. ｺﾈｸﾀ(54) CONNECTOR(54) ｺﾝﾀｸﾄ ﾋﾟﾝ（8017) CONTACT PIN (8017) ｺﾈｸﾀ(RM) CONNECTOR(RM) ｺﾈｸﾀ(SRCN） CONNECTOR(SRCN) ｺﾈｸﾀ(SRCN） CONNECTOR(SRCN) ｺﾈｸﾀ(SRCN) CONNECTOR(SRCN) ｺﾈｸﾀ(8016） CONNECTOR(8016) M8化粧ﾋﾞｽ PANEL SCREW （略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.） （略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.）...
  • Page 70 工事材料表 工事材料表 工事材料表 工事材料表 INSTALLATION MATERIALS 番 号 名  称 NAME ｸｰﾗｰﾊﾟﾃ COOLER PUTTY ｲﾗｯｸｽﾁｭｰﾌﾞ(A) INSULATION TUBE(A) ｺﾈｸﾀ(NCS) CONNECTOR ｺﾈｸﾀ(NCS) CONNECTOR(NCS) ｱｰｽ板 COPPER STRAP ｺﾈｸﾀ(8016) CONNECTOR P貼りﾏｰｸ.11. P STICKER.11. ｺﾈｸﾀ(54) CONNECTOR(54) ｺﾝﾀｸﾄ ﾋﾟﾝ（8017) CONTACT PIN (8017) ﾎｰﾙﾌﾟﾗｸﾞ HOLE PLUG （略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.） （略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.）...
  • Page 71 工事材料表 工事材料表 工事材料表 工事材料表 INSTALLATION MATERIALS 番 号 名  称 NAME ｱｰｽ板 COPPER STRAP ｼｰﾙﾄﾞｽﾘｰﾌﾞ SHIELD SLEEVE 圧着端子 CRIMP-ON LUG 圧着端子 CRIMP-ON LUG 圧着端子 CRIMP-ON LUG 貼りﾏｰｸ STICKER ｺﾈｸﾀ(54) CONNECTOR(54) ｺﾝﾀｸﾄ ﾋﾟﾝ（8017) CONTACT PIN (8017) 圧着端子 CRIMP-ON LUG 圧着端子 CRIMP-ON LUG （略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.）...
  • Page 72 工事材料表 工事材料表 工事材料表 工事材料表 INSTALLATION MATERIALS 番 号 名  称 NAME ﾎｰﾙﾌﾟﾗｸﾞ HOLE PLUG ｱｰｽ板 COPPER STRAP ｺﾝﾀｸﾄ ﾋﾟﾝ（8017) CONTACT PIN (8017) 圧着端子 CRIMP-ON LUG ﾎｰﾙﾌﾟﾗｸﾞ HOLE PLUG 貼りﾏｰｸ.1. STICKER.1. ｺﾈｸﾀ(54) CONNECTOR(54) 圧着端子 CRIMP-ON LUG ｱｰｽ板 COPPER STRAP （略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.） （略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.）...
  • Page 73 工事材料表 INSTALLATION MATERIALS 番 号 名  称 NAME ｺﾈｸﾀ(8016） CONNECTOR(8016) ｱｰｽ線組品 GROUNDING WIRE 貼りﾏｰｸ.J201. STICKER.J201. ｺﾈｸﾀ(54) CONNECTOR(54) ｺﾝﾀｸﾄ ﾋﾟﾝ（8017) CONTACT PIN (8017) ｺﾈｸﾀ(RM) CONNECTOR(RM) ｺﾈｸﾀ(SRCN) CONNECTOR(SRCN) ｺﾈｸﾀ(SRCN） CONNECTOR(SRCN) ｺﾈｸﾀ(SRCN） CONNECTOR(SRCN) ｺﾈｸﾀ(8016) CONNECTOR （略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.） 006-030-670 CODE NO. TYPE CP10-06610 型名／規格...
  • Page 74 工事材料表 INSTALLATION MATERIALS 番 号 名  称 NAME P貼りﾏｰｸ.11. P STICKER.11. ｺﾈｸﾀ(54) CONNECTOR(54) ｺﾝﾀｸﾄ ﾋﾟﾝ（8017) CONTACT PIN (8017) ﾎｰﾙﾌﾟﾗｸﾞ HOLE PLUG ｱｰｽ板 COPPER STRAP ｼｰﾙﾄﾞｽﾘｰﾌﾞ SHIELD SLEEVE 圧着端子 CRIMP-ON LUG 圧着端子 CRIMP-ON LUG 圧着端子 CRIMP-ON LUG 貼りﾏｰｸ STICKER （略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.） 006-030-670 CODE NO.
  • Page 75 工事材料表 INSTALLATION MATERIALS 番 号 名  称 NAME ｺﾈｸﾀ(54) CONNECTOR(54) ｺﾝﾀｸﾄ ﾋﾟﾝ（8017) CONTACT PIN (8017) 圧着端子 CRIMP-ON LUG 圧着端子 CRIMP-ON LUG ﾎｰﾙﾌﾟﾗｸﾞ HOLE PLUG ｱｰｽ板 COPPER STRAP 貼りﾏｰｸ.1. STICKER.1. ｺﾈｸﾀ(54) CONNECTOR(54) ｺﾝﾀｸﾄ ﾋﾟﾝ（8017) CONTACT PIN (8017) 圧着端子 CRIMP-ON LUG （略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.） 006-030-670 CODE NO.
  • Page 76 工事材料表 INSTALLATION MATERIALS 番 号 名  称 NAME 圧着端子 CRIMP-ON LUG ﾎｰﾙﾌﾟﾗｸﾞ HOLE PLUG ｱｰｽ板 COPPER STRAP （略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.） 006-030-670 CODE NO. TYPE CP10-06610 略  図 型名／規格 OUTLINE DESCRIPTIONS FV5.5-4 CODE NO. 000-538-123 NO.4567 CODE NO. 000-800-729 WEA-1004-0 CODE NO.
  • Page 77 A-19...
  • Page 78 A-20...
  • Page 79 A-21...
  • Page 80 A-22...
  • Page 81 A-23...
  • Page 82 A-24...
  • Page 83 A-25...
  • Page 84 A-26...
  • Page 89 Oct.31'03...
  • Page 90 Dec. 10, '02...
  • Page 94 D-10...
  • Page 95 D-11...
  • Page 96 D-12...
  • Page 97 D-13...
  • Page 98 D-14...
  • Page 99 D-15...
  • Page 100 D-16...
  • Page 101 D-17...
  • Page 102 D-18...
  • Page 103 D-19...
  • Page 104 D-20...

  • Page 105: Interconnection Diagrams

    DPYC-1.5 TRANSFORMER PT-400 WEA1004 W=50,1.2m TITLE T.YAMASAKI CSH-81/82/83 名称 T.TAKENO カラースキャニングソナー T.Matsuguchi 相互結線図 MASS NAME COLOR SCANNING SONAR C1290-C01- K INTERCONNECTION DIAGRAM 外部ｲﾝﾀｰﾌｪｲｽ INTERFACE UNIT CS-120A -313-761HV J201 他端に同じ SAME AS THE OTHER SIDE CS-120C -313-761HV CN-A1/A2/A3 副指示器 SUB DISPLAY...
  • Page 106 チャ アオ 10S1258,φ18.6 30m MAX. チャ ムラ チャ (CN-A4/7/10) ECX3C-2V-T,φ13.7 (CN-A5/8/11) (14S4382)30m MAX. (CN-A6/9/12) TITLE CSH-235/235F/235K/835/585/535/735 E. MIYOSHI NAME カラースキャニングソナー操作制御部 TAKAHASHI. T 相互結線図 Y. Hatai MASS REMARK COLOR SCANNING SONAR PROCESSOR UNIT INTERCONNECTION DIAGRAM C1304-C01- B FURUNO ELECTRIC CO., LTD.

This manual is also suitable for:

Csh-84

Table of Contents