NEC NVM-2000 Manual
Installing an expansion drive
Hide thumbs
Also See for NVM-2000:
- Installation manual (40 pages) ,
- Manual (18 pages) ,
- Replacement instructions manual (17 pages)
Related Manuals for NEC NVM-2000
Summary of Contents for NEC NVM-2000
- Page 1 All manuals and user guides at all-guides.com NVM-2000 Installing an Expansion Drive Part No. 17511MINS01 Issue 1-0, June 2001...
- Page 2 All manuals and user guides at all-guides.com This manual has been developed by NEC America, Inc. It is intended for the use of its customers and service person- nel, and should be read in its entirety before attempting to install or program the system. Any comments or sugges- tions for improving this manual would be appreciated.
- Page 3 All manuals and user guides at all-guides.com Table of Contents Installing an Expansion Drive ........1 Introduction .
- Page 4 All manuals and user guides at all-guides.com Table of Contents Issue 1-0...
-
Page 5: Tools And Materials Needed
Installing an Expansion Drive Introduction This supplement provides instructions for installing an expansion (slave) drive in the NVM-2000 Tools and Materials Needed ESD Wrist Strap (to be worn on wrist and attached to a grounded metal object at all times) - Page 6 All manuals and user guides at all-guides.com Installing an Expansion Drive Install the Drive 8. Remove the cabinet cover as follows: If the power switch on your cabinet is mounted on the rear of the cabinet (above the power supply vent fan), slide the cover/front panel assembly 1 3/4 inches towards the front of the cabinet, and lift up.
- Page 7 All manuals and user guides at all-guides.com Installing an Expansion Drive Install the Drive 10. Remove all jumpers from the expansion (slave) hard drive. However, do not change any jumpers on the hard drive (master) that is installed in your cabinet. 11.
- Page 8 All manuals and user guides at all-guides.com Installing an Expansion Drive Install the Drive Set the bucket assembly off to the side. Do not disconnect any wires or ribbon cables from either the floppy drive or the hard drive. Note: You may also see a screw securing a green (chassis ground) to the hard drive/floppy drive bucket assembly (part C on Figure 6).
- Page 9 All manuals and user guides at all-guides.com Installing an Expansion Drive Install the Drive Secure the expansion drive in place with four screws. See Figure 8. DT-expHD-10 cut-away view Figure 8 Refer to Figure 9. Using the screws you previously removed, re-attach the hard drive/ floppy drive bucket assembly to the side of the expansion hard drive.
- Page 10 All manuals and user guides at all-guides.com Installing an Expansion Drive Install the Drive 13. If your desktop has a front cabinet that was secured with spring clips, then perform the follow- ing steps: Use screws to secure the outer two slides (parts A and B on Figure 10) to the to the bottom holes on the expansion hard drive U-brackets.
- Page 11 All manuals and user guides at all-guides.com Installing an Expansion Drive Install the Drive Use Figure 3 as a reference for panel location. To re-attach the front panel to the cabinet, simply push the spring clips into the holes of the cabinet until the clips snap and lock the front panel in place.
- Page 12 All manuals and user guides at all-guides.com Installing an Expansion Drive Install the Drive 16. Plug the middle connector of the ribbon cable into the master hard drive. See Figure 13. IMPORTANT Insert the connector on the ribbon cable so that the red stripe on the rib- bon cable is closest to the power connector on the hard drive.
- Page 13 All manuals and user guides at all-guides.com Installing an Expansion Drive Install the Drive 17. Select one of the three available (extra) power supply connectors and connect the power sup- ply to the expansion hard drive. See Figure 14. Note: You may find that the available (extra) power supply wires with connectors are bundled and secured with pull-ties.
- Page 14 All manuals and user guides at all-guides.com Installing an Expansion Drive Write the Hardware Settings for the New Drive to CMOS Write the Hardware Settings for the New Drive to CMOS Write the Hardware Settings for the New Drive to CMOS You must write the settings for the new expansion (slave) drive to CMOS.
- Page 15 All manuals and user guides at all-guides.com Installing an Expansion Drive Write the Hardware Settings for the New Drive to CMOS Procedure B: Write Expansion Drive Settings to CMOS Note: You should have completed the two steps in Determine the Proper Procedure for Writing to CMOS (on page 10) before you continue with this procedure.
- Page 16 All manuals and user guides at all-guides.com Installing an Expansion Drive Write the Hardware Settings for the New Drive to CMOS Issue 1-0...
- Page 17 All manuals and user guides at all-guides.com NEC America, Inc., Corporate Networks Group 4 Forest Parkway, Shelton, CT 06484 Tel: 800-365-1928 Fax: 203-926-5458 cng.nec.com Other Important Telephone Numbers Sales: ........203-926-5450 Customer Service: .