Related Manuals for Mira Advance J97I
Summary of Contents for Mira Advance J97I
- Page 1 MIRA ADVANCE ATLP LOW PRESSURE ADJUSTABLE TEMPERATURE LIMIT THERMOSTATIC PUMPED ELECTRIC SHOWER User Guide These instructions are to be left with the user...
-
Page 2: Important Safety Information
Important Safety Information WARNING - This shower can deliver scalding temperatures, cause fire, electric shock or other personal injury if not operated, or maintained in accordance with the instructions, warnings and cautions contained in this guide and on the appliance. Please read the important safety information and the operation section of this guide before using the shower. - Page 3 14. DO NOT change the handset model. Fit only shower heads recommended by Mira and do no fit any additional device to restrict the water outlet flow. 15. When adjusting the handset mode, point handset away from body and make sure that the water temperature has stabilised before continuing to shower.
-
Page 4: Decommissioning And Recycling
Only Kohler Mira recommended accessories should be used. 23. DO NOT perform any unspecified modifications, or drill or cut holes in the product other than instructed by this guide. -
Page 5: Shower Models
J97K 9.0 kW Guarantee For domestic installations, Mira Showers guarantee the Mira Advance ATLP against any defect in materials or workmanship for a period of two years from the date of purchase (shower fittings for one year). For non-domestic installations, Mira Showers guarantee the Mira Advance ATLP against any defect in materials or workmanship for a period of one year from the date of purchase. -
Page 6: Operation
Operation 1. How Your Shower Works Hot water is produced by pumping cold water through a heating tank. The shower constantly monitors the following conditions: • The incoming cold water temperature. • The showering temperature. • The flow rate of water. •... - Page 7 2. What Affects Shower Performance? The shower's top priority is to keep the desired water temperature constant. To maintain this temperature, the shower may have to automatically change the rate of water flowing through the appliance. Any of the following conditions can cause the shower to change the flow rate (force of the shower) in order to keep the temperature constant.
- Page 8 Thermostatic Performance To maintain thermostatic performance, the shower may override the selected flow condition. The selected flow indicated does NOT change. Continuous Operation (over 30 minutes) The appliance has a built in timer to prevent continuous operation. This feature cannot be altered and switches the shower off automatically after 30 minutes of continuous use.
- Page 9 3. Using the Shower Refer to section: 'Important Safety Information' first. 1. With the electrical supply turned on, 2. Select the desired flow by pushing push Start/Stop. either once or twice. 3. Check water temperature before 4. Allow 10-15 seconds for any entering shower.
-
Page 10: Fault Diagnosis
Only a competent tradesperson should remove the front cover. We recommend any maintenance work is carried out by a Mira service Engineer or qualified tradesperson. Reset the Shower This is the first solution to the appliance not operating (i.e. the reset light is illuminated). - Page 11 • Recommission the shower (refer to section: 'Commissioning' in the 'Mira Advance Installation Guide'). • In rare cases, hot water may be retained within the shower causing a failure to continue even though the underlying cause may have been corrected.
- Page 12 Maximum temperature is set too low. Adjust Maximum Temperature, refer to section: 'Set Maximum Temperature Shower temperature is not hot enough. and Commissioning Cycle' in the 'Mira Advance ATLP Pumped Electric Shower Installation Guide'. Problem with incoming water supply. Hose or showerhead blocked.
-
Page 13: Maintenance
Maintenance User Maintenance - Cleaning Many household cleaners contain abrasives and chemical substances, and should not be used for cleaning plated or plastic fittings. These finishes should be cleaned with a mild washing up detergent or soap solution, and then wiped dry using a soft cloth. Note! If any of the button lights are flashing or pulsing continuously (in excess of 15 seconds) this may indicate that the button is stuck, this can be avoided by keeping the unit clean. - Page 14 Notes...
- Page 15 Notes...
-
Page 16: Customer Support
● Products purchased ex-showroom display. T: 01 531 9337 ● Disinfection or descaling to reduce bacterial E: customerserviceeire@mirashowers.com growth or contamination. www.mirashowers.ie Mira is a registered trade mark Registered Offi ce: EU Importer address of Kohler Mira Limited. Cromwell Road, K/E S.A.S.