Table of Contents
Advertisement
34230-AVR75 Engelsk 03/03/1998 14:19 Side 29
The following functions of the AVR75
may be controlled through the Menu
Control System:
INPUT SELECTOR
you may change the audio or video input
by using the
or
⁄
¤
position the on-screen cursor
or
. When either input
AUDIO
VIDEO
type is highlighted in reverse video use
the
or
buttons
i
‹
›
source you wish to listen to or view.
Remember that the video source should
be selected first when you wish to watch
one source and listen to another.
To select a digital audio input use the
or
buttons
i
⁄
¤
screen cursor
next to
>
Press
and note that the word
Select j
will be highlighted in reverse
DIGITAL
video. Then use the
or
‹
to select the desired digital source. Note
that when any digital source is selected,
the audio source will indicate
vice versa.
You may also use this menu to turn the
attenuation, or ATT, function on or off
for the selected analog source only by
moving the cursor to the
using the
or
buttons
‹
›
or
. When the ATT function is
ON
OFF
enabled the input level is reduced to
prevent overloading the input circuits
when playing a highly modulated analog
recording.
On-Screen Display
SURROUND MODE
(see figure #15) you may change the
surround mode by using the
buttons
i
: At this menu
cursor
next to
>
or
buttons
‹
›
buttons
to
mode. To change the delay time position
i
next to
the cursor next to
>
and then use the
select desired delay time for the surround
to select the
channels. Note that an adjustment for
the delay time of the center channel is
possible only in the Dolby Digital mode.
TEST TONE
adjust the front, center and surround
speaker output levels. For information
to position the on-
on this procedure, see page 20.
.
DIGITAL
SETUP MENU
using the Setup menus, see page 18.
buttons
i
›
SLEEP TIMER SET
you to set the sleep timer, which will
and
place the unit in a standby mode after a
**
set period of time. To reach this menu,
press the
⁄
position the on-screen cursor
SLEEP TIMER
. At the next screen, the
j
line and
ATT
TIMER SET
to select
the cursor will be next to
i
Use the
or
‹
amount of time before turn off and note
that the time will blink. Press the
button so that the on-screen cursor
is next to
TIMER OFF/ON
or
buttons
‹
›
press
Select j
29
: At this menu
stop flashing indicating that the timer
has been started. Press
or
so that the cursor is next to
⁄
¤
to position the on-screen
TO MAIN MENU
and using the
j
MODE
to select the desired
returns to the screen the time figure
i
will appear next to the words
SURROUND CH
TIMER
or
buttons
to
remaining before shut off at any time
i
‹
›
by pressing the
the remote and viewing the
Information Display ¯
display (see figure #12).
: At this menu you may
Position the on-screen cursor
to
menu system and return to normal
operation.
: For information on
: This enables
or
buttons
to
i
¤
next to
>
Figure 15
and press
Select
SLEEP
menu (see figure #16),
.
TIMER SET
buttons
to select the
i
›
¤
>
. Use the
i
to highlight
and
ON
. The time figure will
Figure 16
one more time
¤
RETURN
and press
Select
. Note that when the
MAIN MENU
SLEEP
. You may check the time
button
z
on
Sleep
Main
or on-screen
next
>
at any time to exit the
MENU OFF
S U R R O U N D
M O D E
M O D E
: P R O
L O G I C
D E L A Y
T I M E
C O N T R O L
C E N T E R
C H
: N O N E
S U R R O U N D
C H
: 2 m s
R E T U R N
T O
M A I N
M E N U
S L E E P
T I M E R
S E T
T I M E R
S E T
1 0 m i n
T I M E R
O F F
O N
R E T U R N
T O
M A I N
M E N U
Advertisement
Table of Contents
