Table of Contents
Advertisement
34230-AVR75 Engelsk 03/03/1998 14:19 Side 18
System Setup
Once the speakers have been placed in
the room and connected, the final step
is to enter the configuration information
and balance the speaker output levels.
Before proceeding further this is a good
time to review the installation section
of the manual to make certain that all
connections are properly made.
1. Plug the unit into an AC wall outlet
and press the
button on the front
Power
panel
. Note that the ring surrounding
1
the front panel switch will turn red, then
green, and the front panel display will
illuminate (more details see page 20).
2. Install the supplied AAA batteries in
the remote as shown on page 15.
3. Check to see that the unit is configured
to the video broadcast standard in use in
your country by pressing and holding the
button
$
on the front panel for
OSD
more than three seconds. The front panel
display will indicate the current setting.
If the setting is not correct, press the
button again until the correct standard
(PAL, SECAM or NTSC) is displayed.
4. Turn on the TV connected to the
receiver. Select the appropriate video
input on the TV.
NOTE: Although the unit will switch
S-Video signals, the on-screen menus
control system is NOT visible on the
S-Video output.
5. Press the
button
Select
remote to bring the
MAIN MENU
on your video screen.
System Configuration
6. Press the
button four times until
¤
the on-screen cursor
SETUP MENU
7. Press
Select j
next screen,
SETUP MENU 1
figure #2).
8.
SETUP MENU 1
information that tells the AVR75 which
type of front and surround speakers
will be used. In turn, these settings will
determine which speakers receive low
frequency (bass) information. For the
purposes of establishing proper bass
reproduction, use the
the speaker being used at any position
is a traditional full-range loudspeaker
that is capable of reproducing sounds
below 100Hz. Use the
for smaller, frequency-limited satellite
speakers that are not able to reproduce
sounds below 100Hz. Note that when
"small" front speakers are used it is
advisable to install a separate subwoofer.
9. Enter the information for the
. speaker by using the
CH
i
on the remote to select the type of
front channel speaker that will be used.
Press the buttons so that
is highlighted to match the
SMALL
speaker type you will use as described in
item #8 above. The
a full-range output to the front left/right
speakers, while the
sends low-frequency sounds to the
subwoofer output. When the selection
has been made, press the
j
on the
so that the on-screen cursor
up
pointing to the
SURROUND CH
of the display.
18
is pointing to
>
(see figure #1).
I N P U T
S U R R O U N D
to move to the
T E S T
S E T
(see
S L E E P
M E N U
enters the
Figure 1
F R O N T
S U R R O U N D
settings if
LARGE
G O
R E T U R N
Figure 2
setting
SMALL
C E N T E R
S U B W O O F E R
G O
FRONT
or
buttons
‹
›
R E T U R N
Figure 3
or
LARGE
L F E
setting sends
LARGE
N I G H T
S E T U P
setting
SMALL
R E T U R N
button once
¤
Figure 4
is
>
. line
M A I N
M E N U
S E L E C T O R
M O D E
T O N E
U P
M E N U
T I M E R : O F F
O F F
S E T U P
M E N U
1
S P E A K E R
S E T T I N G
C H .
L A R G E
S M A L L
C H .
L A R G E
S M A L L
N O N E
T O
S E T
U P
M E N U
2
T O
M A I N
M E N U
S E T U P
M E N U
2
C H .
L A R G E
S M A L L
N O N E
O N
O F F
T O
S E T
U P
M E N U
3
T O
M A I N
M E N U
S E T U P
M E N U
3
L E V E L
C O N T R O L
O F F : 0 d B
-
1 0 d B
M O D E
: O F F
O N
L O C K
: L O C K
U N L O C K
T O
M A I N
M E N U
Advertisement
Table of Contents
