Table of Contents
Advertisement
34230-AVR75 Engelsk 03/03/1998 14:19 Side 27
On-Screen Menus
The AVR75's on-screen menu system
provides both a window into the
operation of the unit and a means of
easily adjusting many system
parameters. In addition to their use in
the setup and configuration of the
AVR75, the menu system provides an easy
means of operating the unit.
To activate the On-Screen display system,
press the
button
OSD
or front panel
. This will cause a
$
status summary display to be shown on
the screen for five seconds (see figure
#6). Once the video displays are enabled,
this status screen will also appear when
the unit is turned on.
If you wish to change the video standard
from the factory preset (PAL), press and
hold the
button
k $
OSD
than 3 seconds until the standard name
appears in the Information Display.
Release the button, then press it again to
change the setting in this sequence:
PAL
SECAM
NOTE: In order to view the on-screen
menu displays the receiver must be
connected to the standard, composite
video input of a TV monitor or projector.
The on-screen displays are NOT visible
via the S-Video output.
The status screen displays the following
information:
AUDIO SOURCE
input currently selected for audio.
VIDEO SOURCE
input currently selected for video.
On-Screen Display
TAPE MONITOR
displayed in this line the output
of the AVR75 is the tape recorder
connected to the
rather than the actual source. This
function is used to monitor a
recording in progress.
DIGITAL INPUT
digital audio source is selected, it
is displayed here.
: This is the currently selected
k
on the remote
MODE
audio/surround mode.
MASTER VOLUME
current volume. The scale uses double
vertical bars
level, while single horizontal dashes
indicate additional range available for
increased volume. The "0dB" reference
point is shown by a solid block
volume is at or above 0dB.
for more
Function Displays and Messages
Once the On-Screen Displays have been
activated, they appear when certain
functions are performed from the front
NTSC
PAL
panel buttons or the remote control.
These messages display the current
function shown on the top line and
information about the selection or
choice on the bottom line.
The following function/operation display
screens are available:
Output Level Display and Adjust
To view an on-screen summary of the
output levels for each channel (see
: This is the
figure #9) press the
: This is the
27
: If "ON" is
Tape1 Inputs §
: If a
Figure 6
: This is the
±
to indicate the volume
Figure 7
-
Í
if the
Figure 8
Figure 9
.
Ch Select m
Figure 10
A U D I O
S O U R C E
:
T U N E R
V I D E O
S O U R C E
:
V C R 2
T A P E
M O N I T O R
:
O F F
D I G I T A L
I N P U T :
* *
M O D E
:
D O L B Y
P R O
L O G I C
M A S T E R
V O L U M E
| | | | | | | | | | | | | | | | | | | | | | | | | |
| |
< F U N C T I O N
S E L E C T >
A U D I O : T U N E R
V I D E O : V C R 1
D I G I T A L : * *
M A S T E R
V O L U M E
| | | | | | | | | | | | | | | | | | | | | | | | | |
| |
F R O N T
L
:
+
1 d B
F R O N T
R
:
-
2 d B
C E N T E R
:
+
1 d B
S U R R O U N D
L
:
- 1 0 d B
S U R R O U N D
R
:
+
3 d B
S U B W O O F E R
:
- 1 0 d B
M O D E
: D O L B Y
P R O
L O G I C
D E L A Y
T I M E : 2 0 m s
Advertisement
Table of Contents
