Table of Contents
Advertisement
34230-AVR75 Engelsk 03/03/1998 14:19 Side 23
When manually tuning stations, observe
the
indicator
Signal Level
the
indicators
Tuned
bars that are visible on the
indicator, the stronger the signal
Level
and the better the station will sound. A
station is properly tuned when the
indicator is illuminated.
Tuned
Tuner Mode
Pressing the
Mode Ó
button on the front panel or remote
selects how a station will be received.
When the button is pressed so that the
indicator
is lit, stations
M
Auto
broadcasting in stereo will be received in
stereo. You may note stereo broadcasts by
observing that the
Stereo
will illuminate. When the
Ó r
is pressed until the
M
goes out, all stations will be received
in a monaural mode regardless of the
method of transmission.
NOTE: When a station is broadcasting in
stereo, but has a weak signal level, the
reproduction may not be acceptable. In
this case, select the Auto Off mode, as
monaural reception is less susceptible to
noise in weak reception areas.
Tuner Presets
There are thirty preset positions that may
be used to store your favorite stations in
any order. These may be used to
memorize the station's frequency and
reception mode. Stations may be preset
automatically or manually, and then
recalled in a variety of ways.
Automatic Station Preset Selection
This process automatically scans the
AM and FM bands and enters all stations
with proper signal strength into the
memory. To automatically preset the
tuner's memory, follow these steps:
1. Select the tuner as the unit's input by
pressing the
button
AM/FM
Basic Operation
2. Using the
and
the first station you wish to preset at the
R
. The more
low end of the AM or FM band.
L
Signal
3. Start the automatic tuning preset by
simultaneously pressing
on the front panel
Tune
⁄
station tuned in step #2 will be entered
into the tuner's memory as
The
Memo
or
FM Mode r
display will show increasing frequencies
to indicate that the auto scan is in
progress.
4. Each time the tuner finds a station the
scanning will pause and the station will
be played for five seconds. During this
time you have the following options:
indicator
K
button
Mode
a. To enter the station in the next
light
open memory position, no action is
Auto
needed. After five seconds the tuner
will enter the station and the preset
number will be visible at the far left
side of the main information display.
b. The frequency band may be
changed by pressing the
button
c. If the tuner is scanning FM
stations, the
from
Auto
Mode
d. If you do not wish to enter the
current station into the preset
memory, press the
Ùs
5. After the desired action is completed,
or five seconds elapse, the tuner scan will
continue. The operation will stop
automatically when all 30 preset
positions are filled or when both
frequency bands have been completely
tuned, whichever comes first. To stop the
automatic preset process at any time
press the
Clear
.
2d
input selection button.
23
buttons
, select
Ùs
Tune
and
Memo
. The
* Ù
.
PRESET 1
indicator
N
will flash. The
AM/FM
2 h
.
may be changed
Mode
to mono by pressing the
button
.
Ó r
button
Tune
⁄
on the front panel or remote.
button
( x
or any
Manual Tuner Preset
Stations may be manually entered into
the tuner's memory in any order. Manual
entry is performed from the remote
control only.
1. Tune to the desired station as outlined
in the Tuner Operation Section.
2. Press the
button
* v
Memo
note that the
indicator
will
N
Memo
flash.
3. While the indicator is flashing for the
next 5 seconds, enter a number from
1 to 30 using the number buttons on the
remote
x
. Any number may be used,
but if another station has already been
programmed into the location number
selected, the previous setting will be lost.
a. To enter a single digit memory
location, press
before the number,
0
or enter the number and wait a few
seconds.
b. If an invalid number (other
than 1–30) is entered, the preset
number in the
Main Information
will flash to alert you
Display J
that the entry is invalid and it will
return to the previous number.
4. When the preset memory has been
properly programmed the
Memo
indicator
N
will stop blinking and the
appropriate preset number will appear in
the
Main Information Display J
Station Name Preset
In addition to identifying stations by
their broadcast frequency, each preset
station without RDS may be assigned a
name using alphanumeric characters.
This enables you to identify a station by
its call letters, program format or any
other five character phrase.
and
.
Advertisement
Table of Contents
