Omron H7CX Series Manual page 5

H7CX
Characteristics
item
Insulation resistance 100 M
between non-continuous contacts
Dielectric strength 2,000 VAC, 50/60 Hz for 1 min between current-carrying metal parts and non-current-carrying metal parts
2,000 VAC (for 100 to 240 VAC), 50/60 Hz for 1 min between power supply and input circuit (1,000 VAC for 24 VAC/
12 to 24 VDC)
1,000 VAC (for H7CX-@SD/-@SD1), 50/60 Hz for 1 min between control output, power supply, and input circuit
(2,000 VAC for models other than H7CX-@SD/-@SD1)
1,000 VAC, 50/60 Hz for 1 min between non-continuous contacts
Impulse withstand 3 kV (between power terminals) for 100 to 240 VAC, 1 kV for 24 VAC/12 to 24 VDC and 12 to 24 VDC
voltage 4.5 kV (between current-carrying terminal and exposed non-current-carrying metal parts) for 100 to 240 VAC,
1.5 kV for 24 VAC/12 to 24 VDC and 12 to 24 VDC
–
Noise immunity 1.5 kV (between power terminals) for 100 to 240 VAC and 24 VAC/12 to 24 VDC,
–
600 V (between input terminals)
Square-wave noise by noise simulator (pulse width: 100 ns/1
Static immunity Destruction:
Malfunction:
Vibration resistance Destruction:
Malfunction:
Shock resistance
Destruction:
Malfunction:
Life expectancy Mechanical:
Electrical:
Approved safety UL508/Listing, CSA C22.2 No. 14, conforms to EN61010-1 (Pollution degree 2/overvoltage category II)
standards Conforms to VDE0106/P100 (finger protection).
(See note 1.)
EMC (EMI)
Emission Enclosure:
Emission AC mains:
(EMS)
Immunity ESD:
Immunity RF-interference:
Immunity Conducted
Disturbance:
Immunity Burst:
Immunity Surge:
Immunity Voltage Dip/Interruption
Degree of protection Panel surface: IP66 and NEMA Type 4 (indoors) (See note 2.)
Weight Approx. 140 g
Note: 1. To meet UL listing requirements with the H7CX-A11@ models, an OMRON P2CF-11-@ or P3GA-11 Socket must be mounted
on the H7CX. Otherwise, H7CX-A11@ models are considered to meet UL508 recognition requirements.
2. A waterproof packing is necessary to ensure IP66 waterproofing between the H7CX and installation panel.
8
W
min. (at 500 VDC) between current-carrying terminal and exposed non-current-carrying metal parts, and
15 kV
8 kV
10 to 55 Hz with 0.75-mm single amplitude each in three directions
10 to 55 Hz with 0.35-mm single amplitude each in three directions
2
294 m/s each in three directions
2
98 m/s each in three directions
10,000,000 operations min.
100,000 operations min. (3 A at 250 VAC, resistive load)
EN61326
EN55011 Group 1 class A
EN55011 Group 1 class A
EN61326
EN61000-4-2:
EN61000-4-3:
EN61000-4-6:
EN61000-4-4:
EN61000-4-5:
EN61000-4-11: 0.5 cycle, 100% (rated voltage)
H7CX
–
480 V for 12 to 24 VDC
m
s, 1-ns rise)
4 kV contact discharge (level 2)
8 kV air discharge (level 3)
10 V/m (Amplitude-modulated, 80 MHz to 1 GHz) (level 3);
10 V/m (Pulse-modulated, 900 MHz
10 V (0.15 to 80 MHz) (according to EN61000-6-2)
2 kV power-line (level 3);
1 kV I/O signal-line (level 4)
1 kV line to lines (power and output lines) (level 2);
2 kV line to ground (power and output lines) (level 3)
H7CX
–
5 MHz) (level 3)