Omron H7CX Series Manual page 11

H7CX (Counter Function)
Settings for All Functions
Note: At the time of delivery, the H7CX is set to the 1-stage counter (2-stage counter for H7CX-AW@/-A4W@ models) configuration. When using as a 2-
stage (or 1-stage) counter, total and preset counter, batch counter, or dual counter, switch to the configuration using the procedure given on page 31.
Settings that cannot be performed with the DIP switch are performed with the operation keys.
Power ON
See note 1. See note 2.
3 s min.
3 s min.
See note 3.
Input mode
Output mode
See note 6.
One-shot
output
time
Counting
speed
Reset input
signal
width
Decimal
point
position
Prescale
value
NPN/PNP
input mode
Display color
Output
allocation
Key protect
level
14
For details on operations in run mode, refer to page 19.
Note: 1. If the mode is switched to the function setting mode during operation, operation will con-
tinue.
2. Changes made to settings in function setting mode are enabled for the first time when the
mode is changed to run mode. Also, when settings are changed, the counter is reset
(present value initialized and output turned OFF) on returning to run mode.
The characters displayed in reverse video are the default settings.
When performing settings with operation keys only, set pin1 of the DIP switch to OFF (factory setting).
If pin 1 of the DIP switch is set to ON, the setting items indicated by
Set each setting item using the
See note 4. See note 4.
(UP) (DOWN) (UP/DOWN A) (UP/DOWN B) (UP/DOWN C)
Note 4: Displayed for output modes other than K-2, D, L, and H only.
(N) (F) (C) (R) (K-1) (P)
Note 5: Display only when the input mode is UP/DOWN A, B, or
C with 6-digit models (with H7CX-AU@/-AW@ models
only for H).
(0.01s) (0.50s) (99.99s)
Note: Displayed only when the output mode is C, R, K-1, P, Q,
A, or K-2.
(30Hz) (5kHz)
(20ms) (1ms)
See note 7.
One digit after
No decimal
decimal point
point
See note 7.
∼ ∼
(0.001) (1.000) (99.999) [9.999]
(PNP
(NPN
input)
input)
(Red) (Green) (Red-green) (Green-red)
Note: Displayed for terminal-block models (except H7CX-A11@) only.
Note: Displayed for H7CX-AU@ models only.
(KP-1) (KP-2) (KP-3) (KP-4)
H7CX (Counter Function)
will not be displayed.
keys. ( key only for 6-digit models)
See note 5.
See note 5. See note 5. See note 5.
(Q) (A) (K-2) (D) (L) (H)
Note 6:
When using as a 2-stage counter:
When using as a
batch counter:
Two digits after Three digits after
decimal point decimal point
Note 7: The displays for 4-digit models are shown inside
parentheses.
(KP-5)
Note 3:
When using as a dual counter:
Dual count
calculating mode
See note.
(Addition) (Subtraction)
Note: Displayed for output modes
other than K-2, D, L, and H only.
One-
shot
(0.01s) (0.50s) (99.99s)
output
Note: Displayed only when the output
2 time mode is C, R, K-1, P, Q, A, or K-2.
One-
shot
(0.01s) (99.99s)
(Outputs held)
output
If the output time is 0.00, '.+# is
1 time
displayed.
Note 1: Displayed for output modes
other than D, L, and H.
Note 2: HOLD cannot be set when
the output mode is K-2.
One-
shot
output (0.01s) (0.50s) (99.99s)
Note: Displayed only when the output
2 time
mode is C, R, K-1, P, Q, A, or K-2.