Operation; Stopping - Stiga Park Series Instruction Manual

(Translation of the Original Instructions)
gine.
5. When the engine is running, gradually acce-
lerate to maximum operating speed (12:E).
Cold Start [B&S Vanguard] [ST.]
1. Engage the transmission (14:A1).
2. Activate the parking brake (12:B).
3. Turn the throttle to full on (12:E).
4. Put the choke on (12:G) (where applicable).
5. Turn the key in the ignition and start the engine.
Before starting work with the machine,
wait a few minutes for the oil to warm up.
Warm Start [B&S Power Built] [B&S Intek]
1. Engage the transmission (14:A1)
2. Activate the parking brake (12:B)
3. Turn the throttle to full on (12:E).
4. Turn the key in the ignition and start the engine.
Warm Start [B&S Vanguard] [ST.]
1. Engage the transmission (14:A1).
2. Activate the parking brake (12:B).
3. Turn the throttle to full on (12:E).
4. Turn the key in the ignition and start the engine.
To proceed see the instructions provi-
ded in heading 7.7.1.
Models 4WD:
Cold Start [B&S Power Built] [B&S Intek]
1. Engage the transmission (15:A1-B1)
2. Activate the parking brake (12:B)
3. Turn the throttle to full on (12:E)
4. Pull the choke out completely
Cold Start [B&S Vanguard] [ST.]
1. Engage the transmission (15:A1-B1).
2. Activate the parking brake (12:B).
3. Turn the throttle to full on (12:E).
4. Put the choke on (12:G) (where applicable).
5. Turn the key in the ignition and start the engine.
Before starting work with the machine,
wait a few minutes for the oil to warm
up.
Warm Start [B&S Power Built] [B&S Intek]
1. Engage the transmission (15:A1-B1)
2. Activate the parking brake (10:B)
3. Turn the throttle to full on (12:E)
4. Turn the ignition key and start the engine.
Warm Start [B&S Vanguard] [ST.]
1. Engage the transmission (15:A1-B1).
2. Activate the parking brake (12:B).
3. Turn the throttle to full on (12:E).
4. Turn the key in the ignition and start the engine.
ENGLISH
To proceed see the instructions provi-
ded in heading 7.6.1.

7.7.1 Operation

To operate with the machine proceed as described
below:
• Press the pedal (12:B) right down then release it.
• Activate the pedal (12:D) to move the machine.
• Go to the work area.
• If front accessories have been installed, activate
the PTO (13:A).
• Commence work.
7.8

STOPPING

To stop the machine, proceed as follows:
• Disengage the PTO (13:A).
• Engage the parking brake (12:B)
• Turn off the engine by turning the ignition key.
• Shut off the petrol cock. This is particularly
important if the machine is to be transported on
a trailer for example.
To avoid backfires, leave the gas lever
in the maximum working position befo-
re turning off the engine.
If you have to leave the machine unat-
tended, disconnect the spark plugs and
remove the key from the ignition.
The engine may be very warm immedia-
tely after it is shut off. Do not touch the
silencer, cylinder or cooling fins. This
can cause burn injuries.
CLEANING
To reduce the risk of fire, keep the engi-
ne, silencer, battery and fuel tank free
from grass, leaves and oil.
To reduce the risk of fire, regularly check
the machine for oil and/or fuel leaks.
Never use high-pressure water jets.
This can damage shaft seals, electrical
components or hydraulic valves.
Never use high-pressure water jets ai-
med directly at the radiator fins. This
could damage the structure of the fins.
Always clean the machine after use. To clean the
machine adhere to the instructions provided below:
• Do not spray water directly onto the engine.
EN
17