Other Functions; Setting The Swing Function; Changing Over Display And Alarm Buzzer (Mute Mode); Energy Saving Functions - Bosch Climate 3000i Operating Instructions For Users

Operation
3.6

Other functions

3.6.1

Setting the swing function

NOTICE
If the louver remain at the lowest position during cooling mode for an
extended period, condensate may form. Adjusting the louver vertically
by hand may cause faults.
▶ Only use the remote control to adjust the louver vertically.
Horizontal swing mode (left/right)
The horizontal position must be set by hand
▶ Switch off the indoor unit and disconnect the power supply.
▶ Flip down the air flow panel ( Fig. 2).
▶ Swivel the louver horizontally by hand into the required position.
▶ Put the air flow panel back in the original position.
Automatic vertical swing mode (up/down)
▶ Press the Swing key for longer than 2 seconds to activate the
automatic vertical Swing mode.
The remote control displays the symbol
▶ To cancel the automatic vertical Swing mode: press the Swing key
again.
Cleaning position
To make cleaning easier, the louver can be brought into a special position
(depending on model).
▶ Press the Mode and Swing keys simultaneously for one second when
the unit is switched off.
▶ To exit the cleaning position: press and hold both keys again.
3.6.2

Changing over display and alarm buzzer (Mute Mode)

▶ To switch on or off the display at the indoor unit and the alarm buzzer:
press LED key.
▶ To display the current room temperature, press the LED key and hold
for 5 seconds.
▶ To display the set temperature: press and hold the LED key for
another 5 seconds.
3.6.3

Energy saving functions

The following energy saving functions can be selected at the unit:
1)
• ECO : operation with fan speed AUTO and set temperature of at
least 24 °C
• GEAR (75%): reduce power consumption by 25 %
• GEAR (50%): reduce power consumption by 50 %
• None of the above symbols: normal operation
▶ To activate an energy saving function, press
required function is displayed.
The ECO function automatically sets a temperature of 24 °C if the
previously set temperature is lower. The function switches off as soon as
the temperature is lowered to less than 24 °C.
1) Only in cooling mode
56
.
key until the
3.6.4

Noise reduction (Silent Mode)

This function reduces the noises emitted by the indoor and outdoor unit
when it is in operation. This is particularly advantageous at night, if you
need to show consideration for your neighbours.
▶ During operation, press the
Exiting the function:
▶ Press the key again for 2 seconds.
-or-
▶ Press the K key, Mode key, Turbo key or Clean key.
When the outdoor unit is in quiet mode, it may not be possible to achieve
the required cooling/heating capacity because the compressor operates
at a low frequency.
3.6.5

Indirect airflow function (Wind avoid me)

This function prevents a direct airflow onto the body.
The function is only available in cooling mode, dehumidification mode
and fan mode.
3.6.6

Turbo cool/Turbo heat

When Turbo cool/Turbo heat is active, the indoor unit operates at
maximum power to heat or cool the room quickly.
▶ Turbo cool: switch on Cooling mode and press the Turbo key.
▶ Turbo heat: switch on heating mode and press the Turbo key.
Exiting the function:
▶ Press the Turbo key again.
3.6.7

Self-cleaning (I clean)

The unit has a self-cleaning function for the evaporator. The self-cleaning
freezes dust, mould and grease. Everything is then quickly defrosted and
dried with hot air.
▶ To activate the self-cleaning: press the Clean key.
CL appears on the display of the indoor unit when self-cleaning is in
progress. Self-cleaning ends automatically after 20 to 45 minutes.
3.6.8 Frost protection (8 °C Heating)
The frost protection can be activated to keep the room temperature at a
minimum of 8 °C.
▶ In heating mode, press the / key 2x within 1 second.
The unit remains off until the temperature falls below 8 °C.
Exiting the function:
▶ Press the K key, Mode key, Turbo key or Clean key.
3.6.9

Key lock function

The keys of the remote control can be locked with the keylock.
▶ To switch the keylock on/off: press the Clean and Turbo keys
simultaneously for 5 seconds.
The symbol appears in the display when the keylock is active.
Climate 3000i – 6721823682 (2021/02)
key for 2 seconds.