Other Functions; Setting The Swing Function; Changing Over Display And Alarm Buzzer; Mode) - Bosch Climate Line 2000 CLL2000-Set 23 W Operating Instructions For Users

Combining timers
The two timers can be set at the same time. Either timer can be
programmed to activate prior to the other
▶ Set the on timer and off timer.
The settings will be automatically combined.
Current time
Setting of ON timer
Setting of OFF timer
Switch-on time
Switch-off time
Table 9 Example
You can not program the on timer and off timer to operate the unit at
different temperatures or with other settings.
3.8

Other functions

3.8.1

Setting the swing function

NOTICE
If the louver remain at the lowest position during cooling mode for an
extended period, condensate may form. Adjusting the louver vertically
by hand may cause faults.
▶ Only use the remote control to adjust the louver vertically.
Horizontal swing mode (left/right)
The horizontal position must be set by hand
▶ Switch off the indoor unit and disconnect the power supply.
▶ Flip down the air flow panel ( Fig. 2).
▶ Swivel the louver horizontally by hand into the required position.
▶ Put the air flow panel back in the original position.
Automatic vertical swing mode (up/down)
▶ Press the Swing key for longer than 2 seconds to activate the
automatic vertical Swing mode.
The remote control displays the symbol
▶ To cancel the automatic vertical Swing mode: press the Swing key
again.
Swivelling the louver manually (up/down)
▶ Press the Swing key until the required position is set.
The setting changes in the following sequence:
Cleaning position
To make cleaning easier, the louver can be brought into a special position
(depending on model).
▶ Press the Mode and Swing keys simultaneously for one second when
the unit is switched off.
▶ To exit the cleaning position: press and hold both keys again.
3.8.2 Changing over display and alarm buzzer (Mute Mode)
▶ To switch on or off the display at the indoor unit and the alarm buzzer:
press LED key.
▶ To display the current room temperature, press the LED key and hold
for 5 seconds.
▶ To display the set temperature: press and hold the LED key for
another 5 seconds.
Climate Line 2000 – 6721831694 (2021/02)
13:00 o'clock
4.0 h
8.5 h
17:00 o'clock
21:30 o'clock
.
3.8.3

Restore function

The indoor unit notes the current and previous setting, for e.g. operation
mode, temperature and fan speed. The restore function can switch
between the previous and current setting.
▶ Press the key to switch to the previous setting.
▶ Hold the key pressed for longer than two seconds to switch to the
current setting.
3.8.4

Turbo cool/Turbo heat

When Turbo cool/Turbo heat is active, the indoor unit operates at
maximum power to heat or cool the room quickly.
▶ Turbo cool: switch on Cooling mode and press the Turbo key.
▶ Turbo heat: switch on heating mode and press the Turbo key.
Exiting the function:
▶ Press the Turbo key again.
3.8.5

Self-cleaning (I clean)

The unit has a self-cleaning function for the evaporator. The self-cleaning
freezes dust, mould and grease. Everything is then quickly defrosted and
dried with hot air.
▶ To activate the self-cleaning: press the Clean key.
CL appears on the display of the indoor unit when self-cleaning is in
progress. Self-cleaning ends automatically after 20 to 45 minutes.
3.8.6 Frost protection (8 °C Heating)
The frost protection can be activated to keep the room temperature at a
minimum of 8 °C.
▶ In heating mode, press the / key 2x within 1 second.
The unit remains off until the temperature falls below 8 °C.
Exiting the function:
▶ Press the K key, Mode key, Turbo key or Clean key.
3.8.7

Key lock function

The keys of the remote control can be locked with the keylock.
▶ To switch the keylock on/off: press the Clean and Turbo keys
simultaneously for 5 seconds.
The symbol appears in the display when the keylock is active.
Operation
23