Installation With Separate Generator - Siemens MAMMOMAT 1000 Nova Installation And Start-Up Instructions Manual

2 2 1 1 - - 2 2
2. 2. Drill
NOTICE NOTICE

Installation with separate generator

Installation with separate generator
The separate generator The separate generator
means of the enclosed wall brackets. For bolting the separate generator to the floor, means of the enclosed wall brackets. For bolting the separate generator to the floor,
the same procedure as for generator with integrated control panel and radiation shield the same procedure as for generator with integrated control panel and radiation shield
applies, see page 21 - 1 applies, see
For attaching the wall brackets to the generator, the uppermost screw hole for the lead- For attaching the wall brackets to the generator, the uppermost screw hole for the lead-
glass stanchions shall be used. Ensure that the wall brackets are secured to the wall with glass stanchions shall be used. Ensure that the wall brackets are secured to the wall with
adequate safety margins. Dowels and screws are not supplied. Please obtain these adequate safety margins. Dowels and screws are not supplied. Please obtain these
locally and ensure that they are suitable for the material used in the wall. locally and ensure that they are suitable for the material used in the wall.
9 9
0 0
2 2
0 0
0 0
M M
A A
M M
Base plate for separate generator Base plate for separate generator
Fig. 3 Fig. 3 Base p Base plate a
M M 1 1 0 0 0 0 0 0 / / 3 3 0 0 0 0 0 0 N N o o v v a a
I I n n s s t t a a l l l l a a t t i i o o n n a a n n d d S S t t a a r r t t - - U U p p
B B o o l l t t i i n n g g t t h h e e s s t t a a n n d d / / g g e e n n e e r r a a t t o o r r t t o o t t h h e e f f l l o o o o r r
Drill the ho the holes a les and in nd insert d sert dowels
and washer DIN 9021B, ISO 7093 or equ and washer DIN 902 1B, ISO 7093 or equivalent. Tighten th
The screws must not come in The screws must not come in contact with any conductive mate-
rial such as reinforcing iron, since the grounding could be com- rial such as reinforcing iron, since the
promised. promised.
Make sure to stay clear of conductive material when fastening the Make sure to stay clear of conductive material when fastening the
screws. screws.
must must
page 21 - 1. .
late and wal nd wall brac l bracket kets for s s for separ
R R e e g g i i s s t t e e r r 3 3
owels and s and screws crews (use L
ivalent. Tighten the screws to 10
be bolted to the floor and/or be secured to the wall by be bolted to the floor and/or be secured to the wall by
Predrilled Predrilled
fixing holes fixing holes
∅ ∅
eparate gen ate generato erator r
S S P P B B 7 7 - - 2 2 3 3 0 0 . . 0 0 3 3 3 3 . . 1 1 1 1
R R e e v v . . 0 0 6 6 0 0 5 5 . . 0 0 6 6
(use Liebi iebig saf g safety do ety dowel M6
e screws to 10 Nm.
contact with any conductive mate-
grounding could be com-
SIEMENS SIEMENS
8 mm 8 mm
Generator secured with wall brackets Generator secured with
P P a a g g e e 2 2 o o f f 4 4
C C S S P P S S S S P P
wel M6 S10/ S10/35 35
Nm.
21 21
0 0
1 1
2 2
0 0
0 0
M M
A A
M M
wall brackets
S S i i e e m m e e n n s s A A G G
M M e e d d i i c c a a l l S S o o l l u u t t i i o o n n s s