Ariston ABS VLS EVO INOX PW 80 Instructions For Installation, Use, Maintenance page 60

EN
• For models equipped with user interface type shown in figure 9: the activation of the anti-legionella cycle
appears as a normal temperature adjustment 70 °C. Activate this function by pressing and holding both the "ECO"
and "+" buttons for 3 s.; once activation is confirmed, LED 60°C (Rif. 4) will flash quickly for 5 s. Permanently de-
activate the function by repeating the above steps; once the deactivation is confirmed, LED 40°C (Rif. 1) will flash
quickly for 4 s.
• For models equipped with user interface type shown in figure 10:
To activate/deactivate the function, press and hold the "mode" button for 4 s. After the "U1" message appears,
press the "set" button.
Select "01" (to activate the function) or "00" (to disable the function), then confirm by pressing the "set" button. To
exit the menu, click "mode" button again.
• For models equipped with user interface type shown in figure 11: the activation of the anti-legionella cycle
appears as a normal temperature adjustment 70°С. Activate this function by pressing and holding both the "FAST"
and "+" buttons for 3 s.; once activation is confirmed, LED 60°С (Rif 4.) will flash quickly for 5 s.
Permanently deactivate the function by repeating the above steps; once the deactivation is confirmed, LED 40°С
(Rif. 1) will flash quickly for 4 s.
Anti-limescale Function
The formation of limescale (calcium carbonate) inside the appliance (in particular on the heating elements) is
linked to the characteristics of the water which may be more or less rich in calcium. It may cause increased noise
in the heating phases and change the sensitivity of the sensors making the control performed by the electronic
control unit more difficult. To decrease this phenomenon first check that the appliance installation conditions are
those recommended (see paragraph "Hydraulic Connections"). The latter is therefore equipped with an "anti-lime-
scale function": it is an automatic protection of the appliance to prevent excessive heating cycles caused by lime-
stone on the heating element. Once the anti-limescale function starts to work, the temperature is lowered to 60
°C (if the temperature set was higher). If the anti-limescale function is activated, the ECO EVO function is disabled.
• For models equipped with a user interface type shown in figure 9 and 11: the anti-limescale function di-
sabled by default and not selectable.
• For models equipped with a user interface type shown in figure 10: the active status of the function is shown
on the display with E70 and "remaining time" that alternate every 3 seconds.
The anti-limescale function is disabled by default, it can be enabled by the user via User Menu; if the alarm occurs
it can be reset by pressing the ON/OFF button to switch on/off the product, but if the problem persists the alarm
will be shown at the next heating cycle.
Wi-Fi Function
• For models equipped with user interface type shown in figure 11:
For detailed information on the Wi-Fi configuration and product registration procedure refer to the enclosed,
dedicated connectivity Quick Start Guide.
Account creation (Fig. 12)
• First download and install the dedicated App on your mobile phone (App name can be found in the quick start
guide).
• Open the APP and click on SIGN UP; Fill in the fields.
• Open the registration reply message received in your mailbox and click on the link to activate the user account.
WI-FI configuration (Fig. 13)
• Press the Wi-Fi Button on the product's control panel to activate the Wi-Fi (Wi-Fi button will blink slow).
• Press the Wi-Fi Button again for 5 seconds on the product's control panel to create the Access Point (Wi-Fi button
will blink fast).
• Log in to Aqua Ariston NET App and follow the wizard to connect and register your product.
Procedure completed (Fig. 14)
The connection is successful when:
• the Wi-Fi button is steady on.
• the App shows the successful registration message
If the connection fails, carefully check and repeat the above steps.
Note: the password cannot be Chinese characters. If there are any Chinese characters, please modify it.
APP LAYOUT (Fig. 15)
• Following functions are included:
• On/off (A)
• Manual mode (B)
• Program mode (C)
• ECO mode (D)
• POWER (E)
• Knob to select temperature(F)
• Remaining time (G)
• Number of showers (H)
60