Changing Over Display And Alarm Buzzer; Mode); Energy Saving Functions; Noise Reduction (Silent Mode) - Bosch Climate Line 5000 Operating Instructions For Users

Cleaning position
To make cleaning easier, the louver can be brought into a special position
(depending on model).
▶ Press the Mode and Swing keys simultaneously for one second when
the unit is switched off.
▶ To exit the cleaning position: press and hold both keys again.
3.6.2 Changing over display and alarm buzzer (Mute Mode)
▶ To switch on or off the display at the indoor unit and the alarm buzzer:
press LED key.
▶ To display the current room temperature, press the LED key and hold
for 5 seconds.
▶ To display the set temperature: press and hold the LED key for
another 5 seconds.
3.6.3

Energy saving functions

The following energy saving functions can be selected at the unit:
1)
• ECO : operation with fan speed AUTO and set temperature of at
least 24 °C
• GEAR (75%): reduce power consumption by 25 %
• GEAR (50%): reduce power consumption by 50 %
• None of the above symbols: normal operation
▶ To activate an energy saving function, press
required function is displayed.
The ECO function automatically sets a temperature of 24 °C if the
previously set temperature is lower. The function switches off as soon as
the temperature is lowered to less than 24 °C.
3.6.4

Noise reduction (Silent Mode)

This function reduces the noises emitted by the indoor and outdoor unit
when it is in operation. This is particularly advantageous at night, if you
need to show consideration for your neighbours.
▶ During operation, press the
Exiting the function:
▶ Press the key again for 2 seconds.
-or-
▶ Press the K key, Mode key, Turbo key or Clean key.
When the outdoor unit is in quiet mode, it may not be possible to achieve
the required cooling/heating capacity because the compressor operates
at a low frequency.
3.6.5

Turbo cool/Turbo heat

When Turbo cool/Turbo heat is active, the indoor unit operates at
maximum power to heat or cool the room quickly.
▶ Turbo cool: switch on Cooling mode and press the Turbo key.
▶ Turbo heat: switch on heating mode and press the Turbo key.
Exiting the function:
▶ Press the Turbo key again.
3.6.6

Self-cleaning (I clean)

The unit has a self-cleaning function for the evaporator. The self-cleaning
freezes dust, mould and grease. Everything is then quickly defrosted and
dried with hot air.
▶ To activate the self-cleaning: press the Clean key.
CL appears on the display of the indoor unit when self-cleaning is in
progress. Self-cleaning ends automatically after 20 to 45 minutes.
1) Only in cooling mode
Climate Line 5000 – 6721831691 (2021/02)
key until the
key for 2 seconds.
3.6.7 Frost protection (8 °C Heating)
The frost protection can be activated to keep the room temperature at a
minimum of 8 °C.
▶ In heating mode, press the / key 2x within 1 second.
The unit remains off until the temperature falls below 8 °C.
Exiting the function:
▶ Press the K key, Mode key, Turbo key or Clean key.
3.6.8

Key lock function

The keys of the remote control can be locked with the keylock.
▶ To switch the keylock on/off: press the Clean and Turbo keys
simultaneously for 5 seconds.
The symbol appears in the display when the keylock is active.
3.6.9

Advanced operating functions

▶ Press the Set key.
▶ Press the Set key or ., / keys to select the function.
– = Indirect airflow function
– = Fresh air function
– = Sleep mode function
– = Follow me function
▶ Confirm selection with the OK key.
Exiting the function:
▶ Repeat the above steps.
Indirect airflow function (Wind avoid me)
This function prevents a direct airflow onto the body.
The function is only available in cooling mode, dehumidification mode
and fan mode.
Fresh air function (Ionizer)
Ions are released into the room to counteract airborne contaminants
such as mould, viruses and allergens.
Sleep mode
The purpose of this function is to save energy during idle times.
After an hour, the unit heats or cools less intensely. To do this, the set
temperature is changed by 1 °C. After two hours the set temperature
changes by a further 1 °C. The new temperature then remains constant.
The function is not available in dehumidification mode and fan mode.
Follow Me function (Follow Me)
The function activates the remote control at the current location in order
to measure the temperature at 3-minute intervals. The indoor unit is now
controlled with reference to these measurements.
The Follow Me function is only available in cooling mode, heating mode
and automatic mode.
Operation
7