1. Manuals
  2. Brands
  3. Lincoln Manuals
  4. Automobile
  5. 2002 Blackwood
  6. Owner's manual

Lincoln 2002 Blackwood Owner's Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Before driving
Starting and driving
Servicing
All rights reserved. Reproduction by any means, electronic or mechanical including
photocopying, recording or by any information storage and retrieval system or translation
in whole or part is not permitted without written authorization from Ford Motor Company.
Ford may change the contents without notice and without incurring obligation.
Copyright © 2002 Ford Motor Company
Contents
2
6
16
88
124
128
145
166
214
221
233
234
1

Advertisement

Table of Contents
loading

Related Manuals for Lincoln 2002 Blackwood

Summary of Contents for Lincoln 2002 Blackwood

  • Page 1: Table Of Contents

    Before driving Introduction Instrumentation Controls and features Seating and safety restraints Starting and driving Starting Driving Roadside emergencies Servicing Maintenance and care Capacities and specifications Customer assistance Reporting safety defects Index All rights reserved. Reproduction by any means, electronic or mechanical including photocopying, recording or by any information storage and retrieval system or translation in whole or part is not permitted without written authorization from Ford Motor Company.

  • Page 2: Introduction

    Introduction CALIFORNIA Proposition 65 Warning WARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. In addition, certain fluids contained in vehicles and certain products of component wear contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
  • Page 3 INFORMATION ABOUT THIS GUIDE The information found in this guide was in effect at the time of printing. Ford may change the contents without notice and without incurring obligation. EMISSION WARRANTY The New Vehicle Limited Warranty includes Bumper-to-Bumper Coverage, Safety Restraint Coverage, Corrosion Coverage, and 7.3L Power Stroke Diesel Engine Coverage.
  • Page 4 Introduction These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert Fasten Safety Belt Air Bag-Side Child Seat Installation Warning Child Seat Tether Anchor Anti-Lock Brake System Traction Control Master Lighting Switch Fog Lamps-Front Fuel Pump Reset Windshield Defrost/Demist...
  • Page 5 Vehicle Symbol Glossary Power Windows Front/Rear Child Safety Door Lock/Unlock Panic Alarm Engine Coolant Do Not Open When Hot Avoid Smoking, Flames, or Sparks Explosive Gas Power Steering Fluid Emission System Passenger Compartment Air Filter Check fuel cap Introduction Power Window Lockout Interior Luggage Compartment Release Symbol...

  • Page 6: Instrumentation

    Instrumentation Turn signal and wiper/washer control (pg. 50) Headlamp control (pg. 16) Rear window defroster control (pg. 19) Power adjustable Parking brake foot pedals Instrument release (pg. 18) panel (pg. 129) dimmer control (pg. 17) Instrument cluster (pg. 8) Gearshift (includes overdrive button) (pg.
  • Page 7 Instrumentation Clock Audio system (pg. 21) (pg. 23) Auxiliary audio controls Auxiliary Climate Traction control (pg. 55) power point control system (pg. 132) (pg. 19) (pg. 41) Auxiliary climate controls (pg. 55)
  • Page 8 Instrumentation WARNING LIGHTS AND CHIMES Low fuel Illuminates when the fuel level in the fuel tank is at, or near, empty (refer to Fuel gauge in this chapter FUEL for more information). Service engine soon Illuminates briefly to ensure the SERVICE system is functional.
  • Page 9 If the light remains on, have your vehicle serviced at the first available opportunity. Light is blinking: Engine misfire is occurring which could damage your catalytic converter. You should drive in a moderate fashion (avoid heavy acceleration and deceleration) and have your vehicle serviced at the first available opportunity.
  • Page 10 Instrumentation Anti-lock brake system (ABS) To confirm the anti-lock brake system (ABS) warning light is functional it will momentarily illuminate when the ignition is turned to the ON position (alternatively for some vehicles when the ignition is moved from the ON position to the START position, the light will momentarily illuminate just prior to reaching the START position).
  • Page 11 Oil pressure/Engine coolant Illuminates when the engine coolant temperature is above the normal range or the engine oil pressure is below normal range. Check the engine oil and coolant level refer to Adding engine oil and Adding coolant in the Maintenance and care chapter.
  • Page 12 Instrumentation Check air suspension (if equipped) Illuminates when the air suspension switch is turned OFF, the load limit SUSP is exceeded or the air suspension system requires servicing. For information on the air suspension system, refer to the Driving chapter. Low washer fluid Illuminates when the windshield washer fluid is low.
  • Page 13 GAUGES Fuel gauge Displays approximately how much fuel is in the fuel tank. The fuel gauge may vary slightly when the vehicle is in motion or on a grade. When refueling the vehicle from empty indication, the amount of fuel that can be added will be less than the advertised capacity due to the reserve fuel.
  • Page 14 Instrumentation Engine coolant temperature gauge Indicates the temperature of the engine coolant. At normal operating temperature, the needle remains within the normal area (the area between the “H” and “C”). If it enters the red section, the engine is overheating. Stop the vehicle as soon as safely possible, switch off the engine immediately and let the engine cool.
  • Page 15 Instrumentation Tachometer Indicates the engine speed in revolutions per minute. Driving with your tachometer pointer continuously at the top of the scale may damage the engine. RPMX1000 Battery voltage gauge Indicates battery voltage. If the pointer moves and stays outside the normal operating range, have the vehicle’s electrical system checked as soon as possible.

  • Page 16: Controls And Features

    Controls and features HEADLAMP CONTROL Rotate the headlamp control to the first position to turn on the parking lamps. Rotate to the second position to turn on the headlamps. High beams Push the lever toward the instrument panel to activate. Pull the lever towards you to deactivate.
  • Page 17 Controls and features Foglamp control The headlamp control also operates the foglamps. The foglamps can be turned on only when the headlamp control is in the position and the high beams are not turned on. Pull headlamp control towards you to turn foglamps on.
  • Page 18 Controls and features AUTOLAMP CONTROL The autolamp system provides light sensitive automatic on-off control of the exterior lights normally controlled by the headlamp control. The autolamp system also keeps the lights on for approximately 20 seconds after the ignition switch is turned to the OFF position.
  • Page 19 Controls and features REAR WINDOW DEFROSTER The rear defroster control is located on the instrument panel. Press the rear defroster control to clear the rear window of thin ice and fog. • A small LED will illuminate when the rear defroster is activated. The ignition must be in the ON position to operate the rear window defroster.
  • Page 20 Controls and features • Located on the back side of the center console (Accessible from the rear seats). • Located on the right side rear trim panel next to the rear seat. • Located in the back bed of the truck, underneath the tonneau cover, on the passenger side near the rear doors.
  • Page 21 CLOCK Press H to set the hour. Press M to set the minute. REVERSE SENSING SYSTEM The Reverse Sensing System (RSS) sounds a tone to warn the driver of obstacles near the rear bumper when R (Reverse) is selected. The RSS will assist the driver in detecting certain objects while: •...
  • Page 22 Controls and features To help avoid personal injury, please read and understand the limitations of the reverse sensing system as contained in this section. Reverse sensing is only an aid for some (generally large and fixed) objects when moving in reverse on a flat surface at “parking speeds”.
  • Page 23 The RSS is automatically enabled when the gear selector is placed in R (Reverse) and the ignition is ON. The RSS control allows the driver to disable the RSS only when the ignition is ON, and the gear selector is in R (Reverse). The OFF indicator remains illuminated when the system is disabled.
  • Page 24 Controls and features Volume/power control Press the control to turn the audio system on or off. Turn the control to raise or lower volume. If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on.
  • Page 25 • to increase volume compensation • to decrease or shut off the volume compensation AM/FM select The AM/FM select control works in radio, tape and CD modes (if equipped). AM/FM select in radio mode This control allows you to select AM or FM frequency bands. Press the control to switch between AM, FM1 or FM2 memory preset stations.
  • Page 26 Controls and features Tune adjust for CD changer • Press to select the previous disc in the CD changer. (Play will begin on the first track of the disc unless the CD changer is in shuffle mode.) Refer to Shuffle feature for more information.
  • Page 27 Scan function The scan function works in radio, tape or CD mode. Scan function in radio mode Press the SCAN control to hear a brief sampling of all listenable stations on the frequency band. Press the SCAN control again to stop the scan mode.
  • Page 28 Controls and features Starting autoset memory preset 1. Select a frequency using the AM/FM select controls. 2. Press the control. 3. When the first six strong stations are filled, the station stored in memory preset control 1 will start playing. If there are less than six strong stations available on the frequency band, the remaining memory preset controls will all store the last strong station available.
  • Page 29 Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers. Tape/CD select • To begin tape play (with a tape loaded into the audio system) while in the radio or CD mode, press the TAPE control. Press the button during rewind or fast forward to stop the rewind or fast forward function.
  • Page 30 Controls and features Fast forward The fast forward control works in tape and CD modes (if equipped). • In the tape mode, tape direction will automatically reverse when the end of the tape is reached. • In CD mode, pressing the control for less than three seconds results in slow forward action.
  • Page 31 Shuffle feature The shuffle feature operates in CD mode and plays all tracks on the current disc in random order. If equipped with the CD changer, the shuffle feature continues to the next disc after all tracks are played. Press the SHUFFLE control to start this feature. Random order play will continue until the SHUFFLE control is pressed again.
  • Page 32 Controls and features Program type • Press the RDS control until FIND program type is displayed. • Use the SEL control to select the program type. With the feature on, use the SEEK or SCAN control to find the desired program type from the following selections: •...
  • Page 33 Mute mode Press the control to mute the playing media. Press the control again to return to the playing media. Digital signal processing (if equipped) The digital signal processing (DSP) feature allows you to change the signal mode to suit your listening tastes.
  • Page 34 Controls and features Rear seat controls The Personal Audio System allows front and rear seat passengers to listen to different media sources (radio, cassette or CD) simultaneously. However, the front and rear seat passengers cannot listen to two different radio stations at the same time.
  • Page 35 Adjusting the volume Press the + control to increase volume. Press the - control to decrease volume. From the rear seat controls, volume control can be set no higher than the current radio setting unless the speakers are turned off. Refer to Turning the rear speakers on and off.
  • Page 36 Controls and features Mode select Push the MODE control to toggle between AM, FM1, FM2, tape, CD or CD changer (if equipped). If in the Personal Audio System mode, SHARED illuminates in the radio display when the front and rear modes are set to the same media.
  • Page 37 Controls and features CD changer Your CD changer is located in the center console. 1. Slide the door to access the CD changer magazine. 2. Press to eject the magazine. 3. Turn the magazine (A) over. 4. Using the disc holder release knob (C), pull the disc holder (B) out of the magazine.
  • Page 38 Controls and features If you pull too hard on the disc holder, the disc holder may come completely out of the magazine. If this happens, reinsert the disc holder back into the magazine while pressing on the lever (A). 5. Line up the CD with the groove of the disc holder.
  • Page 39 ONLY use the magazine supplied with the CD changer, other types will damage the unit. Keep the CD changer door closed. Coins and foreign objects will damage the CD player and void your audio system warranty. Do not insert any promotional (odd shaped or sized) discs, or discs with removable labels into the CD player as jamming may occur.
  • Page 40 Controls and features CD units are designed to play commercially pressed 12 cm (4.75 in) audio compact discs only. Due to technical incompatibility, certain recordable and re-recordable compact discs may not function correctly when used in Ford CD players. Irregular shaped CDs, CDs with a scratch protection film attached, and CDs with homemade paper (adhesive) labels should not be inserted into the CD player.
  • Page 41 (24 miles). This range can be affected by “signal modulation.” Signal modulation is a process radio stations use to increase their strength/volume relative to other stations. • Terrain. Hills, mountains and tall buildings between your vehicle’s antenna and the radio station signal can cause FM reception problems. Static can be caused on AM stations by power lines, electric fences, traffic lights and thunderstorms.
  • Page 42 Controls and features Turning the EATC off Press OFF. The Outside Temperature function will continue to operate until the ignition is turned off. AUTOMATIC FLR • DEF Automatic operation Press AUTOMATIC and select the desired temperature. The selected temperature and the word AUTO will appear in the display window. The EATC system will either heat or cool to achieve the selected temperature.
  • Page 43 To control the temperature, select any temperature between 18°C (65°F) and 29°C (85°F) by pressing the blue (cooler) or red (warmer) buttons. For continuous maximum cooling, push the blue button until 16°C (60°F) is shown in the display window. The EATC will continue maximum cooling (disregarding the displayed temperature) until a warmer temperature is selected by pressing the red button.
  • Page 44 Controls and features Fan speed ( When AUTOMATIC is pressed, fan speed is adjusted automatically for existing conditions. You can override fan speed at any time. To control fan speed manually, use the thumbwheel or steering wheel control to cancel automatic fan speed operation.
  • Page 45 • MAX A/C-Uses recirculated air to cool the vehicle. The temperature will display 16°C (60°F). The temperature control becomes non-functional. The EATC will maintain the maximum cooling mode (disregarding the displayed or selected temperature). To exit, press AUTOMATIC or any other override controls. MAX A/C is noisier than normal A/C but more economical and will cool the inside of the vehicle faster.
  • Page 46 Controls and features Displaying outside temperature Press OUTSIDE TEMP to display the outside air temperature. It will be displayed until OUTSIDE TEMP is pressed again. If the selected temperature is changed while the outside temperature is displayed, the new temperature will be displayed for four seconds after it is changed, then the outside temperature will return to the window.
  • Page 47 • Remove any snow, ice or leaves from the air intake area at the base of the windshield. • If your vehicle has been parked with the windows closed during hot weather, the air conditioner will do a much faster job of cooling if you drive for two or three minutes with the windows open.
  • Page 48 Controls and features Turn the fan speed control to the desired position. Select for air to flow through these vents. Select for air to flow through these vents. - VOLUME + MODE SEEK MEMORY – VOLUME BAND SEEK MEMORY – VOLUME BAND SEEK...
  • Page 49 POSITIONS OF THE IGNITION 1. ACCESSORY, allows the electrical accessories such as the radio to operate while the engine is not running. 2. LOCK, locks the steering wheel, automatic transmission gearshift lever and allows key removal. 3. OFF, shuts off the engine and all accessories without locking the steering wheel.
  • Page 50 Controls and features TURN SIGNAL CONTROL • Push down to activate the left turn signal. • Push up to activate the right turn signal. SPEED CONTROL To turn speed control on • Press ON. Vehicle speed cannot be controlled until the vehicle is traveling at or above 48 km/h (30 mph).
  • Page 51 To turn speed control off • Press OFF or • Turn off the vehicle ignition. Once speed control is switched off, the previously programmed set speed will be erased. To set a speed • Press SET ACCEL. For speed control to operate, the speed control must be ON and the vehicle speed must be greater than 48 km/h (30 mph).
  • Page 52 Controls and features If your vehicle slows down more than 16 km/h (10 mph) below your set speed on an uphill, your speed control will disengage. This is normal. Pressing RES will re-engage it. Do not use the speed control in heavy traffic or on roads that are winding, slippery, or unpaved.
  • Page 53 To set a lower set speed • Press and hold COAST. Release the control when the desired speed is reached or • Press and release COAST to operate the Tap-Down function. Each press will decrease the set speed by 1.6 km/h (1 mph) or •...
  • Page 54 Controls and features To disengage speed control • Depress the brake pedal. Disengaging the speed control will not erase the previously programmed set speed. Pressing OFF will erase the previously programmed set speed.
  • Page 55 To return to a previously set speed • Press RESUME. For RESUME to operate, the vehicle speed must be faster than 48 km/h (30 mph). STEERING WHEEL CONTROLS These controls allow you to operate some radio and climate control features. Radio control features •...
  • Page 56 Controls and features Climate control features • Press TEMP up or down to adjust temperature. • Press FAN up or down to adjust fan speed. TILT STEERING Pull the tilt steering control toward you to move the steering wheel up or down.
  • Page 57 Controls and features Push (tap) the end of the stalk briefly for a single swipe (no wash). Push and hold for three swipes with wash. Push and hold for a longer wash (up to ten seconds). Speed dependent wipers When the windshield wiper control is set on the intermittent settings, speed-sensitive front wipers automatically adjust as the vehicle’s speed changes.
  • Page 58 Controls and features The trip computer only works when the ignition is in the ON position. Trip computer features follow: Selectable features English/metric display Press this control to change the trip computer display from metric to English units. Press again to change from English to metric units.
  • Page 59 • To reset the average fuel economy: 1. Press the MODE control repeatedly until AVG F/ECON is displayed (no other display is resettable). 2. Press the E/M and MODE controls simultaneously. Off. In this mode the display will go blank indicating the system is off. Compass zone adjustment The compass in the mirror is set in ZONE eight at the factory.
  • Page 60 Controls and features Compass calibration adjustment The compass may need calibration adjustment if: • the compass ZONE is set correctly and the trip computer display window is not showing the correct heading • “CAL” is displayed in the trip computer display window Perform this adjustment in an open area free from steel structures and high voltage lines.
  • Page 61 One-touch moon roof You can move the glass panel of the moon roof back to open or tilt up to ventilate the vehicle. To open the moon roof: The moon roof is equipped with an automatic, one-touch, express opening feature. Press the rear portion of the control.
  • Page 62 Controls and features Power tonneau cover controls The operation of the left and right tonneau cover controls are identical. Press the portion of the control to fully open the power tonneau cover. Press the portion of the control to fully close the power tonneau. To disable the tonneau cover controls when using your valet key, lock the key switch in the center...
  • Page 63 Rear door lamps The rear door lamps light when: • any door or tonneau cover is opened. • the instrument panel dimmer switch is held up until the courtesy lamps come on. • the remote entry controls are pressed and the ignition is OFF. The rear door lamps can be turned on by pressing the rocker controls next to each lamp.
  • Page 64 Controls and features ILLUMINATED VISOR MIRROR Lift the mirror cover to turn on the visor mirror lamps. HOMELINK UNIVERSAL TRANSCEIVER The HomeLink Universal Transceiver, located on the driver’s visor, provides a convenient way to replace up to three hand-held transmitters with a single built-in device.
  • Page 65 Controls and features also recommended that a new battery be placed in the hand-held transmitter of the device being programmed to HomeLink for quicker training and accurate transmission of the radio-frequency signal. 1. Press and hold the two outside buttons releasing only when the red light begins to flash after 20 seconds.
  • Page 66 Controls and features 7. Press and release the “learn” or “smart” button. (The name and color of the button may vary by manufacturer.) Note: There are 30 seconds in which to initiate step eight. 8. Return to the vehicle and firmly press, hold for two seconds and release the HomeLink button.
  • Page 67 Reprogramming a single HomeLink button To program a device to HomeLink using a HomeLink button previously trained, follow these steps: 1. Press and hold the desired HomeLink button. Do NOT release the button. 2. The red indicator light will begin to flash after 20 seconds. Without releasing the HomeLink button, follow step 2 in the “Programming”...
  • Page 68 Controls and features Window lock The window lock feature allows only the driver to operate the power windows. To lock out all the window controls except for the driver’s press the left side of the control. Press the right side to restore the window controls. One touch down •...
  • Page 69 Controls and features CHILDPROOF DOOR LOCKS When these locks are set, the rear doors cannot be opened from the inside. The rear doors can be opened from the outside when the doors are unlocked. The childproof locks are located on rear edge of each rear door and must be set separately for each door.
  • Page 70 Controls and features Power fold mirrors (if equipped) Press the control to retract or extend the outside rear view mirrors. If the mirrors are extended and are pushed-in manually, they will deploy back out after a short period of time; likewise, if they are retracted and pulled-out manually, they will deploy back in.
  • Page 71 POSITIVE RETENTION FLOOR MAT Position the driver floor mat so that the eyelet is over the pointed end of the retention post and rotate forward to lock in. Make sure that the mat does not interfere with the operation of the accelerator or the brake pedal.
  • Page 72 Controls and features The outside edge of the tonneau cover, or the top edge of the pickup box, must remain clear of excessive ice, snow, dirt, or other debris to ensure proper closure of the tonneau cover and prevent damage to the vehicle. NOTE: Slide-in campers cannot be installed on this vehicle.
  • Page 73 Controls and features The tonneau cover can be operated by the following: • overhead console button • key fob button • keyless entry key pad • manually The Overhead console button and Keyless entry pad features will only operate the tonneau cover with the vehicle in P (Park) or N (Neutral), the ignition in any position and both tailgate dual doors must be closed.
  • Page 74 Controls and features To open the cover Manually: If an electrical or battery failure happens, your vehicle is equipped with a manual release lever that can open the tonneau cover. 1. To open, locate the manual release lever under the right front corner of the pickup box.
  • Page 75 To open the tonneau cover from the inside, pull the “T” shaped handle and push up on the tonneau cover panel. The handle is composed of a material that will glow for hours in darkness following brief exposure to ambient light. With the tonneau cover popped up the right tailgate door can be opened to exit.
  • Page 76 Controls and features • When the ignition is in the OFF position, the indicator will flash once every 2 seconds to indicate the SecuriLock a theft deterrent. • When the ignition is in the ON position, the indicator will glow for 3 seconds to indicate normal system functionality.
  • Page 77 OFF and restart the engine with all other objects on the key ring held away from the ignition key. Check to make sure the coded key is an approved Lincoln coded key. If your keys are lost or stolen you will need to do the following: •...
  • Page 78 Controls and features 1. Insert the first previously programmed coded key into the ignition and turn the ignition from 1 (OFF) to 3 (ON) (maintain ignition in 3 (ON) for at least one second, but no more than ten seconds). 2.
  • Page 79 Controls and features The remote entry system allows you to: • lock or unlock all vehicle doors without a key. • open the power tonneau cover. • activate the personal alarm. The panic alarm feature will only operate with the ignition in the OFF position.
  • Page 80 Controls and features Locking the doors Press this control to lock all doors. The doors will lock and the lamps will flash. To confirm doors are closed and locked, press this control a second time within three seconds. The door(s) will lock again, the horn will chirp once and the lamps will flash.
  • Page 81 Replacing the battery The remote transmitter is powered by one coin type three-volt lithium battery CR2032 or equivalent. Typical operating range will allow you to be up to 10 meters (33 feet) away from your vehicle. A decrease in operating range can be caused by the following factors: •...
  • Page 82 Controls and features Programming remote transmitters It is necessary to have all (maximum of four — original and/or new) of your remote transmitters available prior to beginning this procedure. To program the transmitters yourself: • Place the key in the ignition and turn from 2 (LOCK) to 3 (OFF) and cycle between 3 (OFF) and 4 (ON) eight times in rapid...
  • Page 83 Deactivating/activating the autolock feature Before following the procedure, make sure that the ignition is OFF and all vehicle doors and the tonneau cover are closed. You must complete steps 1-7 within 30 seconds or the procedure will have to be repeated. If the procedure needs to be repeated, you must wait 30 seconds.
  • Page 84 Controls and features • To program position two, repeat the previous procedure using control • To program position three, repeat the previous procedure but press controls 1 and 2 simultaneously. The memory feature also allows you to recall previously stored positions with your remote transmitter(s).
  • Page 85 Controls and features • on the owner’s wallet card in the glove compartment • taped to the computer module • or at your dealer. When pressing the controls on the keyless entry keypad, press the middle of the controls to ensure a good activation. Anti-scan feature The anti-scan feature prevents 7 8 9 0...
  • Page 86 Controls and features If you wish to erase your personal code, use the following instructions: 4. Enter factory set code. 5. Press 1/2 control within five seconds of step one. 6. Press 7/8 control and 9/0 control at the same time within five seconds of step 2.
  • Page 87 Controls and features Locking the doors with the keyless entry system It is not necessary to enter the factory or personal code prior to 7 8 9 0 locking all doors. To lock the doors: • Press the 7/8 control and the 9/0 control at the same time.

  • Page 88: Seating And Safety Restraints

    Seating and safety restraints FRONT SEATS Two-way adjustable head restraints Your vehicle’s seats are equipped with head restraints which are vertically adjustable. The purpose of these head restraints is to help limit head motion in the event of a rear collision. To properly adjust your head restraints, lift the head restraint so that it is located directly behind your head or as close to that position as possible.
  • Page 89 Seating and safety restraints Reclining the seatback can cause an occupant to slide under the seat’s safety belt, resulting in severe personal injuries in the event of a collision. The control is located on the outboard side of the seat cushion. Press to raise or lower the front portion of the seat cushion.
  • Page 90 Seating and safety restraints Memory seats/rearview mirrors/adjustable pedals This system allows automatic positioning of the driver seat, outside rearview mirrors, and adjustable pedals to three programmable positions. The memory seat control is located on the driver door. • To program position one, move the driver seat to the desired position using the seat controls.
  • Page 91 Seating and safety restraints • Slide the control to to heat the seatback and the seat cushion. • Slide the control to to cool the seatback and the seat cushion. In heat mode: • Rotate the thumbwheel to select the desired heat level from 0 (OFF) to 5 (MAX).
  • Page 92 Seating and safety restraints • There is a filter located under both front seats. • It can be accessed from the second row seat. Move the front seat all the way forward and up to ease access. To remove climate control seat air filter: •...
  • Page 93 Seating and safety restraints • Remove filter. To install climate control seat air filter: • First, position the filter in it’s housing making sure that the far forward end is all the way up in the housing. Then push in on the center of the outside edge of the filter and rotate up into the housing until it clips into position.
  • Page 94 Seating and safety restraints Push control to lower head restraint. Folding down the rear seats Each seat can be folded down into the load floor position. 1. Remove the head restraint. • Pull the head restraint up to the highest position. •...
  • Page 95 Seating and safety restraints 2. Pull control to release seat. 3. Pull seatback toward front seat and down into load floor position.
  • Page 96 Seating and safety restraints 4. Make sure seat is pushed all the way down and locks into position. Returning the seat to seating position Always be sure that the seat is in a latched position, whether the seat is occupied or empty. If not latched, the seat may cause injury during a sudden stop.
  • Page 97 Seating and safety restraints 2. Pull control on the side of the seat to release seat cushion from the load floor position. 3. Lift seatback up until it locks into vertical position. 4. Return the head restraint to its original position.
  • Page 98 Seating and safety restraints SAFETY RESTRAINTS Safety restraints precautions Always drive and ride with your seatback upright and the lap belt snug and low across the hips. To reduce the risk of injury, make sure children sit where they can be properly restrained. Never let a passenger hold a child on his or her lap while the vehicle is moving.
  • Page 99 Seating and safety restraints Safety belts and seats can become hot in a vehicle that has been closed up in sunny weather; they could burn a small child. Check seat covers and buckles before you place a child anywhere near them. Combination lap and shoulder belts 1.
  • Page 100 Seating and safety restraints • Front seats • Rear seats The front and rear outboard safety restraints in the vehicle are combination lap and shoulder belts. The front passenger and rear seat outboard safety belts have two types of locking modes described below: Vehicle sensitive mode The vehicle sensitive mode is the normal retractor mode, allowing free shoulder belt length adjustment to your movements and locking in...
  • Page 101 Seating and safety restraints When to use the automatic locking mode • Any time a child safety seat is installed in the vehicle. Children 12 years old and under should be properly restrained in the rear seat whenever possible. Refer to Safety restraints for children or Safety seats for children later in this chapter.
  • Page 102 Seating and safety restraints • Rear seats 2. Grasp the shoulder portion and pull downward until the entire belt is extracted. 3. Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode.
  • Page 103 Seating and safety restraints After any vehicle collision, the front passenger outboard seat belt system must be checked by a qualified technician to verify that the “automatic locking retractor” feature for child seats is still functioning properly. In addition, all seat belts should be checked for proper function.
  • Page 104 Seating and safety restraints Safety belt height adjustment Your vehicle has safety belt height adjustments for the driver, front passenger and rear outboard passengers. Adjust the height of the shoulder belt so the belt rests across the middle of your shoulder. To lower the shoulder belt height, push the button and slide the height adjuster down.
  • Page 105 Seating and safety restraints Do not use extensions to change the fit of the shoulder belt across the torso. Safety belt warning light and indicator chime The safety belt warning light illuminates in the instrument cluster and a chime sounds to remind the occupants to fasten their safety belts. Conditions of operation If...
  • Page 106 Seating and safety restraints If... The driver’s safety belt is not buckled approximately 5 seconds after the safety belt warning light has turned off... The driver’s safety belt is buckled while the safety belt indicator light is illuminated and the safety belt warning chime is sounding...
  • Page 107 Seating and safety restraints Reasons given... “Seat belts don’t work” “Traffic is light” “Belts wrinkle my clothes” “The people I’m with don’t wear belts” “I have an air bag” “I’d rather be thrown clear” Do not sit on top of a buckled safety belt to avoid the Belt Minder chime.
  • Page 108 Seating and safety restraints Before following the procedure, make sure that: • the parking brake is set • the gearshift is in P (Park) (automatic transmission) or the neutral position (manual transmission). • the ignition switch is in the OFF position •...
  • Page 109 Seating and safety restraints three seconds with the safety belt warning light off, then followed by flashing the safety belt warning light four times per second for three seconds again. 9. After receiving confirmation, the deactivation/activation procedure is complete. Safety belt maintenance Inspect the safety belt systems periodically to make sure they work properly and are not damaged.
  • Page 110 Seating and safety restraints event of a collision this module may save information related to the collision including information about the air bag system and impact severity. This information will assist Ford Motor Company in servicing the vehicle and in helping to better understand real world collisions and further improve the safety of future vehicles.
  • Page 111 Do not attempt to service, repair, or modify the air bag supplemental restraint systems or its fuses. See your Ford or Lincoln Mercury dealer. Modifications to the front end of the vehicle, including frame, bumper, front end body structure and tow hooks may affect the performance of the air bag sensors increasing the risk of injury.
  • Page 112 Seating and safety restraints Children and air bags For additional important safety information, read all information on safety restraints in this guide. Children must always be properly restrained. Accident statistics suggest that children are safer when properly restrained in the rear seating positions than in the front seating position.
  • Page 113 Seating and safety restraints The air bags inflate and deflate rapidly upon activation. After air bag deployment, it is normal to notice a smoke-like, powdery residue or smell the burnt propellant. This may consist of cornstarch, talcum powder (to lubricate the bag) or sodium compounds (e.g., baking soda) that result from the combustion process that inflates the...
  • Page 114 Seating and safety restraints impact sensors, the system wiring, the air bag system readiness light, the air bag back up power and the air bag ignitors). Determining if the system is operational The SRS uses a readiness light in the instrument cluster or a tone to indicate the condition of the system.
  • Page 115 Seating and safety restraints Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a collision. Always follow the instructions and warnings that come with any infant or child restraint you might use.
  • Page 116 Seating and safety restraints safety seat you put in your vehicle. If you do not install and use the safety seat properly, the child may be injured in a sudden stop or collision. When installing a child safety seat: • Review and follow the information presented in the Air bag supplemental restraint system (SRS) section in this chapter.
  • Page 117 Seating and safety restraints Installing child safety seats in combination lap and shoulder belt seating positions Air bags can kill or injure a child in a child seat. NEVER place a rear-facing child seat in front of an active air bag. If you must use a forward-facing child seat in the front seat, move the seat all the way back.
  • Page 118 Seating and safety restraints 3. While holding the shoulder and lap belt portions together, route the tongue through the child seat according to the child seat manufacturer’s instructions. Be sure the belt webbing is not twisted. 4. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) for that seating position until...
  • Page 119 The bolt holes are in the bottom of the rear edge of the front passenger seat cushion frame. The anchor bracket must be installed using the instructions provided with the kit. Tether anchorage hardware kits (part number 613D74) including instructions, may be obtained at no charge from any Ford or Lincoln/Mercury dealer.
  • Page 120 Seating and safety restraints Tighten the anchor according to specifications. Otherwise, the safety seat may not be properly secured and the child may be injured in a sudden stop or collision. Attaching child safety seats with tether straps Most new forward-facing child safety seats include a tether strap which goes over the back of the seat and hooks to an anchoring point.
  • Page 121 Seating and safety restraints 1. Position the child safety seat on the seat cushion. 2. Route the child safety seat tether strap over the back of the seat. 3. Locate the correct anchor for the selected seating position. (Shown with the seats folded down.) •...
  • Page 122 Seating and safety restraints 4. Clip the tether strap to the anchor as shown. If the tether strap is clipped incorrectly, the child safety seat may not be retained properly in the event of a collision. 5. Refer to the Installing child safety seats in combination lap and shoulder belt seating positions section of this chapter for...
  • Page 123 Seating and safety restraints Your vehicle may be equipped with LATCH anchors for child seat installation at the seating positions marked with the child seat symbol. Never attach two LATCH child safety seats to the same anchor. In a crash, one anchor may not be strong enough to hold two child safety seat attachments and may break,...

  • Page 124: Starting

    Starting PREPARING TO START YOUR VEHICLE Engine starting is controlled by the powertrain control system. This system meets all Canadian Interference-Causing Equipment standard requirements regulating the impulse electrical field strength of radio noise. When starting a fuel-injected engine, avoid pressing the accelerator before or during starting.
  • Page 125 3. Make sure the gearshift is in P (Park). 4. Make sure the parking brake is set. 5. Turn the key to 4 (ON) without turning the key to 5 (START). Starting...
  • Page 126 Starting Make sure the corresponding lights illuminate or illuminate briefly. If a light fails to illuminate, have the vehicle serviced. • If the driver’s safety belt is fastened, the light may not illuminate. STARTING THE ENGINE Note: Whenever you start your vehicle, release the key as soon as the engine starts.
  • Page 127 Guarding against exhaust fumes Although odorless and colorless, carbon monoxide is present in exhaust fumes. Take precautions to avoid its dangerous effects. If you ever smell exhaust fumes of any kind inside your vehicle, have your dealer inspect and fix your vehicle immediately. Do not drive if you smell exhaust fumes.

  • Page 128: Driving

    Driving BRAKES Your service brakes are self-adjusting. Refer to the scheduled maintenance guide for scheduled maintenance. Occasional brake noise is normal and often does not indicate a performance concern with the vehicle’s brake system. In normal operation, automotive brake systems may emit occasional or intermittent squeal or groan noises when the brakes are applied.
  • Page 129 ABS warning lamp warning lamp in the instrument cluster momentarily illuminates when the ignition is turned to the ON position. If the light does not illuminate momentarily at start up, remains on or continues to flash, the ABS needs to be serviced. With the ABS light on, the anti-lock brake system is disabled and normal braking is still effective unless the...
  • Page 130 Driving The BRAKE warning lamp in the instrument cluster illuminates and remains illuminated (when the ignition is turned ON) until the parking brake is released. Always set the parking brake fully and make sure that the gearshift is securely latched in P (Park). The parking brake is not recommended to stop a moving vehicle.
  • Page 131 • Do not operate the vehicle with the power steering pump fluid level below the MIN mark on the reservoir. If the power steering system breaks down (or if the engine is turned off), you can steer the vehicle manually, but it takes more effort. If the steering wanders or pulls, check for: •...
  • Page 132 Driving If the light is illuminated while driving and the air suspension system switch is not turned off, safely pull off the road at your earliest convenience. Turn the ignition switch from 4 (On) to 3 (Off) and 4 (On) again.
  • Page 133 TRACTION-LOK AXLE This axle provides added traction on slippery surfaces, particularly when one wheel is on a poor traction surface. Under normal conditions, the Traction-Lok axle functions like a standard rear axle. If a single drive wheel should spin-up, the Traction-Lok axle will transfer torque to the other wheel if it has traction.
  • Page 134 Driving Loaded vehicles, with a higher center of gravity, may handle differently than unloaded vehicles. Extra precautions, such as slower speeds and increased stopping distance, should be taken when driving a heavily loaded vehicle. Your vehicle has the capability to haul more cargo and people than most passenger cars.
  • Page 135 Do not rock the vehicle if the engine is not at normal operating temperature or damage to the transmission may occur. Do not rock the vehicle for more than a few minutes or damage to the transmission and tires may occur or the engine may overheat.
  • Page 136 Driving R (Reverse) With the gearshift lever in R (Reverse), the vehicle will move backward. Always come to a complete stop before shifting into and out of R (Reverse). N (Neutral) With the gearshift lever in N (Neutral), the vehicle can be started and is free to roll.
  • Page 137 Each time the vehicle is started, the transmission will automatically return to normal overdrive mode. Every time the vehicle is shut off and restarted, you must press the transmission control switch to cancel overdrive operation if driving in overdrive is not desired. 2 (Second) Use 2 (Second) to start-up on slippery roads or to provide...
  • Page 138 Driving • GAWR (Gross Axle Weight Rating): Carrying capacity for each axle system. The GAWR is specific to each vehicle and is listed on the Safety Certification Label on the driver’s door pillar. • GCW (Gross Combined Weight): The combined weight of the towing vehicle (including occupants and cargo) and the loaded trailer.
  • Page 139 your vehicle including both gross vehicle weight and front and rear gross axle weight rating limits. Under no circumstance should these limitations be exceeded. Exceeding any vehicle weight rating limitation could result in serious damage to the vehicle loss of vehicle control, vehicle rollover, and/or personal injury.
  • Page 140 Driving Follow these guidelines to ensure safe towing procedure: • Stay within your vehicle’s load limits. If exceeded, cargo should be removed from the trailer and/or the vehicle until all weights are within specified limits. • Thoroughly prepare your vehicle for towing. Refer to Preparing to tow in this chapter.
  • Page 141 Towing trailers beyond the maximum recommended gross trailer weight exceeds the limit of the vehicle and could result in engine damage, transmission damage, structural damage, loss of control and personal injury. Preparing to tow Use the proper equipment for towing a trailer and make sure it is properly attached to your vehicle.
  • Page 142 Driving If you use a rental trailer, follow the instructions that the rental agency gives to you. Do not attach safety chains to the bumper. Trailer brakes Electric brakes and manual, automatic or surge-type trailer brakes are safe if installed properly and adjusted to the manufacturer’s specifications.
  • Page 143 Trailer towing tips • Practice turning, stopping and backing up before starting on a trip to get the feel of the vehicle trailer combination. When turning, make wider turns so the trailer wheels will clear curbs and other obstacles. • Allow more distance for stopping with a trailer attached. •...
  • Page 144 Driving These guidelines are designed to ensure that your transmission is not damaged due to insufficient lubrication. All Rear Wheel Drive (RWD) vehicles: This applies to all cars and 4x2 trucks/sport utilities with rear wheel drive capability. • Place the transmission in N (Neutral) •...

  • Page 145: Roadside Emergencies

    In the United States, this card is found in the Owner Guide portfolio in the glove compartment in Ford vehicles and is mailed to you if you own a Mercury or Lincoln. In Canada, the card is found in the Owner Information Guide in the glove compartment.
  • Page 146 If you need to arrange roadside assistance for yourself, Ford Motor Company will reimburse a reasonable amount. To obtain reimbursement information, U.S. Ford or Mercury vehicles customers call 1-800-241-3673; Lincoln vehicle customers call 1–800–521–4140. Canadian customers who need to obtain reimbursement information, call 1–800–665–2006.
  • Page 147 Roadside emergencies The fuel pump shut-off switch is located in the passenger’s foot well, by the kick panel. Use the following procedure to reset the fuel pump shut-off switch. 1. Turn the ignition to the OFF position. 2. Check the fuel system for leaks. 3.
  • Page 148 Roadside emergencies Note: Always replace a fuse with one that has the specified amperage rating. Using a fuse with a higher amperage rating can cause severe wire damage and could start a fire. Standard fuse amperage rating and color Fuse Mini Standard rating...
  • Page 149 The fuses are coded as follows. Fuse/Relay Fuse Amp Location Rating 7.5A Roadside emergencies Passenger Compartment Fuse Panel Description Radio, Amplifier, I/P fuse 31 Powertrain Control Module (PCM), Instrument cluster, Electronic Automatic Temperature Control (EATC), Overhead Trip Computer Module (OTC), Navigation module, Clock Cigar lighter, Data Link Connector (DLC) Mirrors, Seats, Pedals, (memory)
  • Page 150 Roadside emergencies Fuse/Relay Fuse Amp Location Rating — — Passenger Compartment Fuse Panel Description Speed control module, Reverse lamp, Reverse Sensing System (RSS), E/C mirror, Central security module, Navigation module Cluster, Brake shift interlock solenoid, Generic Electronic Module (GEM), RSS, Air suspension, OTC, Compass, Automatic parking brake release Console blower relay...
  • Page 151 Fuse/Relay Fuse Amp Location Rating — — Relay 1 — Relay 2 — Relay 3 — Relay 4 — Relay 5 — Power distribution box The power distribution box is located in the engine compartment. The power distribution box contains high-current fuses that protect your vehicle’s main electrical systems from overloads.
  • Page 152 Roadside emergencies Always disconnect the battery before servicing high current fuses. Always replace the cover to the power distribution box before reconnecting the battery or refilling fluid reservoirs If the battery has been disconnected and reconnected, refer to the Battery section of the Maintenance and specifications chapter. The high-current fuses are coded as follows.
  • Page 153 Fuse/Relay Fuse Amp Power Distribution Box Description Location Rating 20A* Fuel pump 20A* Alternator field 20A* Rear auxiliary power point 15A* A/C clutch 20A* Box power point – Not used — Not used 10A* Delayed accessory PCM, Fuel injectors, Fuel pump relay, 15A* Idle Air control, Mass air flow sensor 10A*...
  • Page 154 Roadside emergencies Fuse/Relay Fuse Amp Location Rating 40A** — — 40A** — — — — — — — — — — — — — — — — — — — 30A CB 50A** *Mini fuses **Maxi fuses CHANGING THE TIRES If you get a flat tire while driving, do not apply the brake heavily.
  • Page 155 The use of tire sealants is not recommended and may compromise the integrity of your tires. Spare tire information Your vehicle is equipped with a spare tire that may be used as a spare or a regular tire. The spare is identical to the other tires on your vehicle. Location of the spare tire and tools The spare tire and tools for your vehicle are stowed in the following locations:...
  • Page 156 Roadside emergencies Removing the spare tire 1. Attach the spare tire lock key (A) to the jack handle (B). 2. Insert the straight end of the jack handle into the rear access hole located near the license plate. Forward motion will stop and resistance to turning will be felt when properly engaged.
  • Page 157 Tire change procedure To prevent the vehicle from moving when you change a tire, be sure the parking brake is set, then block (in both directions) the wheel that is diagonally opposite (other side and end of the vehicle) to the tire being changed.
  • Page 158 Roadside emergencies 3. Turn OFF the air suspension switch. Refer to Air suspension system in the Driving chapter for more information. 4. Block the diagonally opposite wheel. 5. Obtain the spare tire and jack from their storage locations. 6. Use the tip of the lug wrench to remove any wheel trim.
  • Page 159 • Front • Rear To lessen the risk of personal injury, do not put any part of your body under the vehicle while changing a tire. Do not start the engine when your vehicle is on the jack. The jack is only meant for changing the tire.
  • Page 160 Roadside emergencies 10. Replace the flat tire with the spare tire, making sure the valve stem is facing outward. Reinstall the lug nuts until the wheel is snug against the hub. Do not fully tighten the lug nuts until the wheel has been lowered.
  • Page 161 Roadside emergencies 3. Park the booster vehicle close to the hood of the disabled vehicle making sure the two vehicles do not touch. Set the parking brake on both vehicles and stay clear of the engine cooling fan and other moving parts.
  • Page 162 Roadside emergencies 3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery. 4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle’s engine, away from the battery and the carburetor/fuel injection system.
  • Page 163 Roadside emergencies 3. Once the disabled vehicle has been started, run both engines for an additional three minutes before disconnecting the jumper cables. Removing the jumper cables Remove the jumper cables in the reverse order that they were connected. 1. Remove the jumper cable from the ground metal surface. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery.
  • Page 164 Roadside emergencies 3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’s battery. After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle conditions.
  • Page 165 WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or, if you are a member, your roadside assistance center. It is recommended that your vehicle be towed with a wheel lift or flatbed equipment. Don’t tow with a slingbelt. Ford Motor Company has not approved a slingbelt towing procedure.

  • Page 166: Maintenance And Care

    Maintenance and care SERVICE RECOMMENDATIONS To help you service your vehicle: • We highlight do-it-yourself items in the engine compartment for easy location. • We provide a scheduled maintenance guide which makes tracking routine service easy. If your vehicle requires professional service, your dealership can provide the necessary parts and service.
  • Page 167 Maintenance and care OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the bottom left corner of the instrument panel. 2. Go to the front of the vehicle and release the auxiliary latch located under the front of the hood, just above the passenger side headlamp.
  • Page 168 Maintenance and care IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 5.4L 4V V8 engine 1. Battery 2. Automatic transmission fluid dipstick 3. Engine oil filler cap 4. Power steering fluid reservoir 5. Engine oil dipstick 6. Brake fluid reservoir 7. Power distribution box 8.
  • Page 169 3. Set the parking brake and ensure the gearshift is securely latched in P (Park). 4. Open the hood. Protect yourself from engine heat. 5. Locate and carefully remove the engine oil level indicator (dipstick). 6. Wipe the indicator clean. Insert the indicator fully, then remove it again.
  • Page 170 Maintenance and care 7. Put the indicator back in and ensure it is fully seated. Adding engine oil 1. Check the engine oil. For instructions, refer to Checking the engine oil in this chapter. 2. If the engine oil level is not within the normal range, add only certified engine oil of the recommended viscosity.
  • Page 171 Ford production and aftermarket (Motorcraft) oil filters are designed for added engine protection and long life. If a replacement oil filter is used that does not meet Ford material and design specifications, start-up engine noises or knock may be experienced. It is recommended you use the appropriate Motorcraft oil filter (or another brand meeting Ford specifications) for your engine application.
  • Page 172 Maintenance and care Do not let the fluid level in the reservoir for the master cylinder fall below the MIN mark. If master cylinder runs dry, this may cause the brakes to fail. WINDSHIELD WASHER FLUID Windshield washer fluid Check the washer fluid whenever you stop for fuel.
  • Page 173 coolant reservoir. If the level falls below, add coolant per the instructions in the Adding engine coolant section. Your vehicle was factory-filled with a 50/50 engine coolant and water concentration. If the concentration of coolant falls below 40% or above 60%, the engine parts could become damaged or not work properly.
  • Page 174 Maintenance and care Adding engine coolant When adding coolant, make sure it is a 50/50 mixture of engine coolant and distilled water. Add the mixture to the coolant reservoir, when the engine is cool, until the appropriate fill level is obtained. Do not add engine coolant when the engine is hot.
  • Page 175 • Do not use alcohol, methanol, brine or any engine coolants mixed with alcohol or methanol antifreeze (coolant). Alcohol and other liquids can cause engine damage from overheating or freezing. • Do not add extra inhibitors or additives to the coolant. These can be harmful and compromise the corrosion protection of the engine coolant.
  • Page 176 Maintenance and care Whenever coolant has been added, the coolant level in the coolant reservoir should be checked the next few times you drive the vehicle. If necessary, add enough 50/50 concentration of engine coolant and distilled water to bring the liquid level to the proper level. If you have to add more than 1.0 liter (1.0 quart) of engine coolant per month, have your dealer check the engine cooling system.
  • Page 177 • Refer to the chart on the coolant container to ensure the coolant concentration in your vehicle will provide adequate freeze protection at the temperatures in which you drive in the winter months. If you drive in extremely hot climates: •...
  • Page 178 Maintenance and care How fail-safe cooling works If the engine begins to overheat: • The engine coolant temperature gauge will move to the red (hot) area. • The and the symbol will illuminate. • The “Service Engine Soon” indicator light will illuminate. If the engine reaches a preset over-temperature condition, the engine will automatically switch to alternating cylinder operation.
  • Page 179 5. Restart the engine and take your vehicle to a service facility. Driving the vehicle without repairing the engine problem increases the chance of engine damage. Take your vehicle to a service facility as soon as possible. CHECKING AND ADDING POWER STEERING FLUID Check the power steering fluid.
  • Page 180 Maintenance and care However, the fluid level should be checked if the transmission is not working properly, i.e., if the transmission slips or shifts slowly or if you notice some sign of fluid leakage. Automatic transmission fluid expands when warmed. To obtain an accurate fluid check, drive the vehicle until it is at normal operating temperature (approximately 30 km [20 miles]).
  • Page 181 Maintenance and care The transmission fluid should be in this range if at normal operating temperature (66°C-77°C [150°F-170°F]). The transmission fluid should be in this range if at ambient temperature (10°C-35°C [50°F-95°F]). High fluid level Fluid levels above the safe range may result in transmission failure.
  • Page 182 Maintenance and care intervals. If the original universal joints are replaced with universal joints equipped with grease fittings, lubrication will also be necessary. BATTERY Your vehicle is equipped with a Motorcraft maintenance-free battery which normally does not require additional water during its life of service.
  • Page 183 When lifting a plastic-cased battery, excessive pressure on the end walls could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the vehicle or battery. Lift the battery with a battery carrier or with your hands on opposite corners.
  • Page 184 Maintenance and care • Always dispose of automotive batteries in a responsible manner. Follow your local authorized standards for disposal. Call your local authorized recycling center to find out more about recycling automotive batteries. AIR FILTER MAINTENANCE Refer to the scheduled maintenance guide for the appropriate intervals for changing the air filter element.
  • Page 185 Maintenance and care 2. Loosen the clamp that secures the air filter cover to the air filter housing and carefully separate the cover from housing. 3. Remove the air filter element from the air filter housing. 4. Install a new air filter element. Be careful not to crimp the filter element edges between the air filter housing and cover.
  • Page 186 Maintenance and care Changing the wiper blades To replace the wiper blades: 1. Pull the wiper arm away from the windshield and lock into the service position. 2. Turn the blade at an angle from the wiper arm. Push the lock pin manually to release the blade and pull the wiper blade down toward the windshield to remove it from the...
  • Page 187 government test course. For example, a tire graded 150 would wear one and one-half (1 1/2) times as well on the government course as a tire graded 100. The relative performance of tires depends upon the actual conditions of their use, however, and may depart significantly from the norm due to variations in driving habits, service practices, and differences in road characteristics and climates.
  • Page 188 Maintenance and care • Adjust tire pressure to recommended specifications found on the Certification Label inside of driver’s door. Tire pressure information can also be found on the Tire Information label located on the inside of the fuel filler door. Improperly inflated tires can affect vehicle handling and can fail suddenly, possibly resulting in loss of vehicle control, vehicle rollover and/or personal injury.
  • Page 189 • Five tire rotation Replacing the tires Replace the tires when the wear band is visible through the tire treads. Due to exposure to the elements and exhaust you should replace the spare tire when you replace the other tires. When replacing full size tires, never mix radial bias-belted, or bias-type tires.
  • Page 190 Maintenance and care Failure to follow these precautions, your vehicle handling may be adversely affected which can lead to loss of vehicle control, vehicle rollover and/or personal injury. Tires that are larger or smaller than your vehicle’s original tires may also affect the accuracy of your speedometer and the performance of your Traction Control Sytem.
  • Page 191 The fuel system may be under pressure. If the fuel filler cap is venting vapor or if you hear a hissing sound, wait until it stops before completely removing the fuel filler cap. Otherwise, fuel may spray out and injure you or others. If you do not use the proper fuel filler cap, excessive pressure or vacuum in the fuel tank may damage the fuel system or cause the fuel cap to disengage in a collision, which may result in possible...
  • Page 192 Maintenance and care clothing and wash skin thoroughly with soap and water. Repeated or prolonged skin contact with fuel liquid or vapor causes skin irritation. • Be particularly careful if you are taking “Antabuse” or other forms of disulfiram for the treatment of alcoholism. Breathing gasoline vapors, or skin contact could cause an adverse reaction.
  • Page 193 Maintenance and care Octane recommendations Your vehicle is designed to use “Premium” unleaded gasoline with an (R+M)/2 octane rating of 91 or higher for optimum performance. (R+M)/2 METHOD The use of gasolines with lower octane ratings may degrade performance. The use of gasolines labeled as “Premium”...
  • Page 194 Maintenance and care Running out of fuel Avoid running out of fuel because this situation may have an adverse affect on powertrain components. If you have run out of fuel: • You may need to cycle the ignition from OFF to ON several times after refueling, to allow the fuel system to pump the fuel from the tank to the engine.
  • Page 195 If you do not use the proper fuel filler cap, excessive pressure or vacuum in the fuel tank may damage the fuel system or cause the fuel cap to disengage in a collision, which may result in possible personal injury. Fuel Filter For fuel filter replacement, see your dealer or a qualified service technician.
  • Page 196 Maintenance and care For consistent results when filling the fuel tank: • Turn the engine/ignition switch to the off position prior to refueling, an error in the reading will result if the engine is left running. • Use the same filling rate setting (low — medium — high) each time the tank is filled.
  • Page 197 Habits • Smooth, moderate operation can yield up to 10% savings in fuel. • Steady speeds without stopping will usually give the best fuel economy. • Idling for long periods of time (greater than one minute) may waste fuel. • Anticipate stopping; slowing down may eliminate the need to stop. •...
  • Page 198 Maintenance and care • Adding certain accessories to your vehicle (for example bug deflectors, rollbars/light bars, running boards, ski/luggage racks) may reduce fuel economy. • To maximize the fuel economy, drive with the tonneau cover installed (if equipped). • Using fuel blended with alcohol may lower fuel economy. •...
  • Page 199 • Have the items listed in your scheduled maintenance guide performed according to the specified schedule. The scheduled maintenance items listed in the scheduled maintenance guide are essential to the life and performance of your vehicle and to its emissions system. If other than Ford, Motorcraft or Ford-authorized parts are used for maintenance replacements or for service of components affecting emission control, such non-Ford parts should be equivalent to genuine...
  • Page 200 Maintenance and care condition. To ready the on-board diagnostics system for I/M testing, a minimum of 30 minutes of city and highway driving is necessary as described below: • First, at least 10 minutes of driving on an expressway or highway. •...
  • Page 201 Maintenance and care 3. At the back of the headlamp, remove the headlamp assembly retainers by pushing rearward and pulling up. 4. Pull the headlamp assembly forward slightly to expose the electrical connectors. 5. Rotate the bulb cover counterclockwise and remove. 6.
  • Page 202 Maintenance and care 8. Without turning, carefully pull the bulb out of the headlamp assembly. Handle a halogen headlamp bulb carefully and keep out of children’s reach. Grasp the bulb only by its plastic base and do not touch the glass. The oil from your hand could cause the bulb to break the next time the headlamps are operated.
  • Page 203 Maintenance and care 5. Release clip and disconnect the electrical connector from the bulb socket. 6. Rotate the bulb socket counterclockwise and remove. 7. Pull the bulb straight out of the socket and push in the new bulb. 8. To complete installation of the parking lamp/turn signal assembly, follow the removal procedures in reverse order.
  • Page 204 Maintenance and care Replacing tail/turn/backup lamp bulbs 1. Open the tailgate dual doors to expose the lamp assembly nuts. 2. Remove the nuts from the lamp assembly. 3. Carefully pry the lamp assembly away from the vehicle to expose the bulb socket.
  • Page 205 Replacing high-mount brakelamp bulbs 1. Remove the two screws from the high-mount brakelamp assembly. 2. Remove the bulb from the lamp assembly by turning counterclockwise. 3. Carefully pull the bulb straight out of the socket and push in the new bulb. 4.
  • Page 206 Maintenance and care Function Number of bulbs Rear cornering lamp Backup lamp License lamp High-mount brake lamp All replacement bulbs are clear in color except where noted. To replace all instrument panel lights - see your dealer AIMING THE HEADLAMPS Your vehicle is equipped with a Vehicle Headlamp Aim Device (VHAD) on each headlamp.
  • Page 207 Horizontal aim adjustment 1. Park the vehicle on a level surface. 2. With the hood open, locate the horizontal indicator and the adjusting screw. They are located below the viewing hole at the rear of the headlamp assembly. 3. Use a 4 mm wrench or socket to turn the horizontal adjusting screw until the “0”...
  • Page 208 Ph shampoo, such as Detail Wash (ZC-3–A), which is available from your authorized Ford, Lincoln or Mercury dealer. Always use a clean sponge or carwash mitt with plenty of water for best results. Dry the vehicle with a chamois or soft terry cloth towel in order to eliminate water spotting.
  • Page 209 Minor scratches or paint damage from road debris may be repaired using the Ultra Touch Prep and Finishing Kit (F7AZ-19K507–BA), which is available at your authorized Ford, Lincoln or Mercury dealer. This kit contains: • Lacquer Touch-Up Paint (ALBZ-19500–XXXXA) •...
  • Page 210 Agitate the area with a sponge and rinse off with plenty of water. Use Extra Strength Tar and Road Oil Removal (B7A-19520–AA), available from your authorized Ford, Lincoln or Mercury dealer, in order to remove tar and grease from wheel rims and covers.
  • Page 211 Clean the outside of the windshield or rear window with a non-abrasive cleaner such as Ultra Clear Spray Glass Cleaner (E4AZ-19C507–AA), available from your authorized Ford, Lincoln or Mercury dealer. If after...
  • Page 212 Maintenance and care cleaning the glass surface, the water sheets from the glass (e.g., does not bead), then the window is clean. The windshield, rear window and wiper blades should be cleaned regularly. Wiper blades can be cleaned with isopropyl (rubbing) alcohol or windshield washer solution.
  • Page 213 Extra Strength Upholstery Cleaner (E8AZ-19523–AA). Cleaning leather seats (if equipped) All Ford, Lincoln and Mercury vehicles with leather seating surfaces have a clear, protective coating over the leather. To clean the leather seats, simply use a soft cloth with Deluxe Leather and Vinyl Cleaner (F2AZ-19521–WA).

  • Page 214: Capacities And Specifications

    Capacities and specifications MOTORCRAFT PART NUMBERS Component Air filter element Fuel filter Oil filter PCV valve Battery Spark plugs-platinum* * Refer to Vehicle Emissions Control Information (VECI) decal for spark plug gap information. REFILL CAPACITIES Fluid Ford Part Name Brake fluid High Performance DOT 3 Motor...
  • Page 215 Capacities and specifications Fluid Ford Part Name Rear axle Motorcraft SAE 75W-140 Synthetic Rear Axle Lubricant Windshield Ultra-Clear washer fluid Windshield Washer Concentrate Add the coolant type originally equipped in your vehicle. Ensure the correct automatic transmission fluid is used. Transmission fluid requirements are indicated on the dipstick or on the dipstick handle.
  • Page 216 Capacities and specifications Add 118 ml (4 oz.) of Additive Friction Modifier C8AZ-19B546-A or equivalent meeting Ford specification EST-M2C118–A, for complete fill of 9.75 inch axles. LUBRICANT SPECIFICATIONS Ford part Item name Hinges, latches, Multi-Purpose striker plates Grease and rotors, seat tracks, fuel filler door hinge and spring...
  • Page 217 Capacities and specifications Ford part Item name Automatic Motorcraft transmission MERCON ATF Power steering Motorcraft fluid MERCON ATF Rear axle Motorcraft SAE 75W-140 High Performance Synthetic Rear Axle Lube Windshield Ultra-clear washer fluid Windshield Washer Concentrate Ensure the correct automatic transmission fluid is used. Transmission fluid requirements are indicated on the dipstick or on the dipstick handle.
  • Page 218 Capacities and specifications ENGINE DATA Engine Cubic inches Required fuel Firing order Spark plug gap Ignition system Compression ratio BLACKWOOD DIMENSIONS Dimension (1) Overall length (2) Overall width (closed mirrors) (3) Overall height (4) Wheel base (5)Track front/rear Vehicle width, including mirrors (extended): 2 363 mm (93 in) 5.4L (4V) V8 engine 91 octane 1-3-7-2-6-5-4-8...
  • Page 219 Capacities and specifications...
  • Page 220 Capacities and specifications IDENTIFYING YOUR VEHICLE Certification label The National Highway Traffic Safety Administration Regulations require that a Certification label be affixed to a vehicle and prescribe where the Certification label may be located. The Certification label is located on the front door latch pillar on the driver’s side.

  • Page 221: Customer Assistance

    • Protection against covered repair costs after your Bumper-to-Bumper Warranty expires. You may purchase Ford ESP from any participating Ford and Lincoln Mercury and Ford of Canada dealer. There are several plans available in various time, distance and deductible combinations which can be tailored to fit your own driving needs.
  • Page 222 Oakville, Ontario L6J 5E4 1-800-565-3673 (FORD) www.ford.ca If you own a Lincoln vehicle and are away from home when your vehicle needs service, or if you need more help than the dealership could provide, after following the steps described above, contact the Ford Customer Relationship Center to find an authorized dealership to help you.
  • Page 223 P.O. Box 2000 Oakville, Ontario L6J 5E4 1-800-565-3673 (FORD) www.ford.ca In order to help you service your Ford or Lincoln Mercury vehicle, please have the following information available when contacting a Customer Relationship Center: • Your telephone number (home and business) •...
  • Page 224 What kinds of cases does the Board review? Unresolved warranty repair concerns or vehicle performance concerns as on Ford and Lincoln Mercury cars and Ford and Lincoln Mercury light trucks which are within the terms of any applicable written new vehicle warranty are eligible for review, except those involving: •...
  • Page 225 • A Ford or Lincoln Mercury dealership representative Consumer candidates for Board membership are recruited and trained by an independent consulting firm. The dealership Board member is chosen from Ford and Lincoln Mercury dealership management, recognized for their business leadership qualities. What the Board needs...
  • Page 226 Customer assistance Oral presentations If you would like to make an oral presentation, indicate YES to question 6 on the application. While it is your right to make an oral presentation before the Board, this is not a requirement and the Board will decide the case whether or not an oral presentation is made.
  • Page 227 Customer assistance UTILIZING THE MEDIATION/ARBITRATION PROGRAM (CANADA ONLY) In those cases where you continue to feel that the efforts by Ford and the dealer to resolve a factory-related vehicle service concern have been unsatisfactory, Ford of Canada participates in an impartial third party mediation/arbitration program administered by the Canadian Motor Vehicle Arbitration Plan (CAMVAP).
  • Page 228 Ford accessories for your vehicle A wide selection of genuine Ford accessories are available for your vehicle through your local authorized Ford, Lincoln Mercury or Ford of Canada dealer. These quality accessories have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and aerodynamic appearance of your vehicle.
  • Page 229 Customer assistance Vehicle Security Styled wheel locks Vehicle security systems Comfort and convenience Air filtration systems Cargo nets Cargo organizers (interior) Cargo trays (interior) Celluar phone holder Engine block heaters Tire step Travel equipment Daytime running lights (DRL) Hitch mount bike carrier Inside mirror with compass display Inside mirror with compass and temperature display Running boards (molded, diamond plate, tubular and stirrup step)
  • Page 230 Customer assistance Carpet floor mats Flat splash guards Front end covers (full) Hood deflectors Locking gas cap Molded “all weather” vinyl floor mats Side window air deflectors Spare tire lock Truck cover Underbody vehicle lighting Universal floor mats Wheels For maximum vehicle performance, keep the following information in mind when adding accessories or equipment to your vehicle: •...
  • Page 231 Customer assistance ORDERING ADDITIONAL OWNER’S LITERATURE To order the publications in this portfolio, contact Helm, Incorporated at: HELM, INCORPORATED P.O. Box 07150 Detroit, Michigan 48207 Or call: For a free publication catalog, order toll free: 1-800-782-4356 Monday-Friday 8:00 a.m. - 6:00 p.m. EST Helm, Incorporated can also be reached by their website: www.helminc.com.
  • Page 232 Customer assistance In the case of 1 or 2 above, the consumer must also notify the manufacturer of the need for the repair of the nonconformity at the following address: Ford Motor Company 16800 Executive Plaza Drive Mail Drop 3NE-B Dearborn, MI 48126...

  • Page 233: Reporting Safety Defects

    Reporting safety defects REPORTING SAFETY DEFECTS (U.S. ONLY) If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Ford Motor Company. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.

  • Page 234: Index

    Index ABS (see Brakes) ...128 Accessory delay ...68 Air bag supplemental restraint system ...109–110 and child safety seats ...112 description ...110 disposal ...114 driver air bag ...112 indicator light ...9, 114 operation ...112 passenger air bag ...112 Air cleaner filter ...184, 214 Air conditioning ...41 rear seat controls ...47 Air suspension ...131...
  • Page 235 instrument panel ...212 interior ...212 plastic parts ...211 safety belts ...213 washing ...208 waxing ...209 wheels ...209 windows ...212 wiper blades ...211 woodtone trim ...212 Climate control (see Air conditioning or Heating) ...41 Clock ...21, 31 Compass, electronic calibration ...60 set zone adjustment ...59 Console overhead ...57...
  • Page 236 Index recommendations ...170 refill capacities ...214 specifications ...216, 218 Exhaust fumes ...127 Fail safe cooling ...177 Floor mats ...71 Fluid capacities ...214 Foglamps ...17 Four-Wheel Drive vehicles preparing to drive your vehicle ...133 Fuel ...190 calculating fuel economy ...195 cap ...194 capacity ...214 choosing the right fuel ...192 comparisons with EPA fuel...
  • Page 237 HomeLink universal transceiver (see Garage door opener) ...64, 66–67 Hood ...167 Ignition ...49, 218 Infant seats (see Safety seats) 115 Inspection/maintenance (I/M) testing ...199 Instrument panel cleaning ...212 cluster ...8, 212 lighting up panel and interior .17 location of components ...8 Jack ...154 positioning ...154 storage ...154...
  • Page 238 Index english/metric button ...58 menu button ...58 Mirrors ...64 automatic dimming rearview mirror ...63 heated ...70 programmable memory ...83 side view mirrors (power) .69–70 Moon roof ...61 Motorcraft parts ...195, 214 Octane rating ...193 Odometer ...14 Oil (see Engine oil) ...168 Overdrive ...57 Panic alarm feature, remote entry system ...80...
  • Page 239 Spare tire (see Changing the Tire) ...155 Spark plugs, specifications ...214, Special notice ...3 ambulance conversions ...3 utility-type vehicles ...3 Specification chart, lubricants ...216, 218 Speed control ...50 Speedometer ...13 Starting your vehicle ...124, 126 jump starting ...160 Steering wheel controls ...50, 55–56 tilting ...56 Tachometer ...15...

  • Page 240: Filling Station Information

    Filling station information Item Required fuel-5.4L 4V V8 engine Fuel tank capacity Tire size and pressure Hood release Engine oil capacity (includes filter change) Coolant capacity Power steering fluid capacity Transmission fluid capacity Use either green-colored Motorcraft Premium Engine Coolant or yellow-colored Motorcraft Premium Gold Engine Coolant.

Table of Contents