Page 1 Table of Contents Introduction Instrument Cluster Warning and control lights Gauges Entertainment Systems AM/FM stereo cassette with CD AM/FM stereo with CD Navigation system Climate Controls Electronic automatic temperature control Lights Headlamps Turn signal control Bulb replacement Driver Controls Windshield wiper/washer control Power windows Mirrors Speed control...
Page 2: Table Of Contents
Table of Contents Seating and Safety Restraints Seating Safety restraints Air bags Child restraints Driving Starting Brakes Traction control/AdvanceTrac Transmission operation Vehicle loading Trailer towing Roadside Emergencies Getting roadside assistance Hazard flasher switch Fuel pump shut-off switch Fuses and relays Changing tires Jump starting Wrecker towing...
Page 3: Table Of Contents
Maintenance and Specifications Hood Engine compartment Engine oil Battery Fuel information Part numbers Refill capacities Lubricant specifications Accessories Index All rights reserved. Reproduction by any means, electronic or mechanical including photocopying, recording or by any information storage and retrieval system or translation in whole or part is not permitted without written authorization from Ford Motor Company.
Page 4: Introduction
State of California to cause cancer and birth defects or other reproductive harm. CONGRATULATIONS Congratulations on acquiring your new Lincoln. Please take the time to get well acquainted with your vehicle by reading this handbook. The more you know and understand about your vehicle the greater the safety and pleasure you will derive from driving it.
Page 5 SAFETY AND ENVIRONMENT PROTECTION Warning symbols in this guide How can you reduce the risk of personal injury and prevent possible damage to others, your vehicle and its equipment? In this guide, answers to such questions are contained in comments highlighted by the warning triangle symbol.
Page 6 Introduction SPECIAL NOTICES Emission warranty The New Vehicle Limited Warranty includes Bumper-to-Bumper Coverage, Safety Restraint Coverage, Corrosion Coverage, and 7.3L Power Stroke Diesel Engine Coverage. In addition, your vehicle is eligible for Emissions Defect and Emissions Performance Warranties. For a detailed description of what is covered and what is not covered, refer to the Warranty Guide that is provided to you along with your Owner’s Guide.
Page 7 Front seat mounted rear facing child or infant seats should NEVER be used in front of a passenger side air bag unless the air bag can be and is turned OFF. Notice to owners of pickup trucks and utility type vehicles Utility vehicles have a significantly higher rollover rate than other types of vehicles.
Page 8 Introduction These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert Fasten Safety Belt Air Bag-Side Child Seat Installation Warning Child Seat Tether Anchor Anti-Lock Brake System Traction Control Master Lighting Switch Fog Lamps-Front Fuel Pump Reset Windshield Defrost/Demist...
Page 9 Vehicle Symbol Glossary Power Windows Front/Rear Child Safety Door Lock/Unlock Panic Alarm Engine Coolant Do Not Open When Hot Avoid Smoking, Flames, or Sparks Explosive Gas Power Steering Fluid Emission System Passenger Compartment Air Filter Check fuel cap 2003 Aviator f/k/a Navigator LS (231) Owners Guide (post-2002-fmt) USA English (fus) Introduction...
Page 10: Instrument Cluster
Instrument Cluster Instrument Cluster WARNING LIGHTS AND CHIMES Warning lights and gauges can alert you to a vehicle condition that may become serious enough to cause expensive repairs. A warning light may illuminate when a problem exists with one of your vehicle’s functions. Many lights will illuminate when you start your vehicle to make sure the bulb works.
Page 11 If the light remains on, have your vehicle serviced at the first available opportunity. Note: The light will illuminate if vehicle refueling is conducted with the engine running. Never refuel vehicle with the engine running. Light is blinking: Engine misfire is occurring which could damage your catalytic converter. You should drive in a moderate fashion (avoid heavy acceleration and deceleration) and have your vehicle serviced at the first available opportunity.
Page 12 Instrument Cluster position to the START position, the light will momentarily illuminate just prior to reaching the START position). If the light remains on, continues to flash or fails to illuminate, have the ABS serviced immediately. If the ABS light remains on, it means the anti-lock brake system has malfunctioned and is disabled, however, the normal brake system will still function unless the brake warning light also remains illuminated and parking brake is off.
Page 13 Speed control Illuminates when the speed control is activated. Engine coolant temperature Illuminates when the engine coolant temperature is high. Stop the vehicle as soon as safely possible, switch off the engine and let it cool. Never remove the coolant recovery cap while the engine is running or hot.
Page 14 Instrument Cluster AWD locked (if equipped) Illuminates when all wheel drive (AWD) is locked. If the light LOCKED continues to flash have the system serviced. Safety belt warning chime Sounds to remind you to fasten your safety belts. BeltMinder chime Sounds intermittently to remind you to fasten your safety belts.
Page 15: Gauges
GAUGES Engine coolant temperature gauge Indicates the temperature of the engine coolant. At normal operating temperature, the needle remains within the normal area (the area between the “H” and “C”). If it enters the red section, the engine is overheating. Stop the vehicle as soon as safely possible, switch off the engine immediately and let the engine cool.
Page 16 Instrument Cluster Fuel gauge Displays approximately how much fuel is in the fuel tank. The fuel gauge may vary slightly when the vehicle is in motion or on a grade. When refueling the vehicle from empty indication, the amount of fuel that can be added will be less than the advertised capacity due to the reserve fuel.
Page 17 Instrument Cluster Tachometer Indicates the engine speed in revolutions per minute. Driving with your tachometer pointer continuously at the top of the scale may damage the engine. 2003 Aviator f/k/a Navigator LS (231) Owners Guide (post-2002-fmt) USA English (fus)
Page 18: Entertainment Systems
Entertainment Systems Entertainment Systems PREMIUM AM/FM STEREO/CASSETTE/SINGLE CD 1. Tape eject control 2. CD eject control 3. Bass/treble control 4. Balance/fade control 5. Compression/shuffle control 6. Select control 7. Side direction/Dolby control 8. Rewind/fast forward control 9. RDS/Mute control Volume/power control Press the control to turn the audio system on or off.
Page 19 If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on. Audio power can also be turned on by pressing the AM/FM select control or the TAPE/CD select control.
Page 20 Entertainment Systems Tune adjust in radio mode • Press to move to the next frequency down the band (whether or not a listenable station is located there). Hold the control to move through the frequencies quickly. • Press to move to the next frequency up the band (whether or not a listenable station is located there).
Page 21 Entertainment Systems Scan function in tape mode Press the SCAN control to hear a short sampling of all selections on the tape. (The tape scans in a forward direction. At the end of the tape’s first side, direction automatically reverses to the opposite side of the tape.) To stop on a particular selection, press the control again.
Page 22 Entertainment Systems If there are less than six strong stations available on the frequency band, the remaining memory preset controls will all store the last strong station available. These stations are temporarily stored in the memory preset controls (until deactivated) and are accessed in the same manner as your original presets.
Page 23 Press the BAL control then press: • to shift sound to the left and • to shift sound to the right. Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers. Press the FADE control then press: •...
Page 24 Entertainment Systems Fast forward The fast forward control works in tape and CD modes. • In the tape mode, tape direction will automatically reverse when the end of the tape is reached. • In CD mode, pressing the control fast forwards the CD within the current track.
Page 25 Compression adjust Compression adjust brings soft and loud CD passages together for a more consistent listening level. Press the COMP control to activate and deactivate compression adjust. Radio data system (RDS) feature This feature allows your audio system to receive station identification or program type from RDS-equipped FM radio stations.
Page 26 Entertainment Systems Program type • Press the RDS control until the FIND program type is displayed. • Use the SEL control to select the program type. With the feature on, use the SEEK or SCAN control to find the desired program type from the following selections: •...
Page 27 Entertainment Systems Soft mute When the vehicle is in reverse, and an obstacle is detected by Rear Park Assist, the radio volume is reduced to a level that allows the warning to be heard. After the obstacle warning is gone, the radio will return to the previously set volume level.
Page 28 Entertainment Systems Speed sensitive volume With this feature, radio volume changes automatically and slightly with vehicle speed to compensate for road and wind noise. The recommended level for speed sensitive volume is from level 1 through level 3. Level 0 turns the speed sensitive volume off and level 7 is the maximum setting.
Page 29 Disc adjust for CD mode • Press to select the previous disc. (Play will begin on the first track of the disc unless shuffle mode is engaged.) Refer to Shuffle feature for more information. Hold the control to continue reversing through the discs. •...
Page 30 Entertainment Systems Scan function in CD mode Press the SCAN control to hear a short sampling of all selections on the CD. (The CD scans in a forward direction, wrapping back to the first track at the end of the CD.) To stop on a particular selection, press the control again.
Page 31 If there are fewer than six strong stations available on the frequency band, the remaining memory preset controls will all store the last strong station available. To deactivate autoset and return to your audio system’s manually set memory stations, press the AM/FM control again. CD select CD mode may be entered by pressing the CD control.
Page 32 Entertainment Systems has been loaded, the door will close and the CD will begin to play. For example, to load a CD into slot 2, press the LOAD control and then press preset 2. Auto load This feature allows you to autoload up to 6 discs into the multi disc CD player internal to the radio.
Page 33 Entertainment Systems When in rewind mode, your audio system will automatically lower the volume level of the playing media. Fast forward The fast forward control works in CD modes. Press and hold the FF control until the desired selection is reached. If the end of the disc is reached, the CD will return to the first track.
Page 34 Entertainment Systems Bass adjust The bass adjust control allows you to increase or decrease the audio system’s bass output. Press the BASS control. Use the SEL control to increase or decrease the amount of bass. Treble adjust The treble adjust control allows you to increase or decrease the audio system’s treble output.
Page 35 Entertainment Systems If RDS is turned ON, you can access the following: • TRAFFIC ON/OFF-Refer to Traffic announcements. • FIND type-Refer to Program type. • SHOW (NAME, TYPE, NONE)- Refer to Radio data system feature. • RDS ON— Refer to Radio data system feature. You can also access COMP ON/OFF.
Page 36 Entertainment Systems RDS traffic scan feature When in traffic mode, you can use the SCAN feature to scan up the frequency band for listenable traffic capable frequencies. With the RDS activated, press the MENU control until TRAFFIC ON is displayed. Press the SCAN control. SCAN TRAFFIC will display. The audio system will scan to all traffic capable frequencies.
Page 37 Program type This feature allows you to search for RDS stations selectively by their program type. Press the MENU control until FIND program type is displayed. Use the SEL control to select the program type. With the feature on, use the SEEK or SCAN control to find the desired program type from the following selections: •...
Page 38 Entertainment Systems Setting the clock Your vehicle is equipped with a separate instrument panel mounted clock. Please refer to Clock in the Driver controls chapter for instructions on setting the clock. Digital signal processing (if equipped) The digital signal processing (DSP) feature allows you to change the signal mode to suit your listening tastes.
Page 39 Press DSP to access the ambiance menu. Press SEL to engage/disengage. Turn the volume control to increase/decrease the level of ambiance. Press the DSP control again to access the occupancy modes. Use the SEL control to optimize the sound based upon the occupants in the vehicle.
Page 40 Entertainment Systems CASSETTE/PLAYER CARE • Use only cassettes that are 90 minutes long or less. • Tighten very loose tapes by inserting a finger or pencil into the hole and turning the hub. • Remove loose labels before inserting tapes. •...
Page 41: Navigation System
LINCOLN NAVIGATION SYSTEM (IF EQUIPPED) Your vehicle may be equipped with a Lincoln Navigation System which allows you to listen to the radio, play CDs and also navigate the vehicle using a navigation DVD.
Page 42 Entertainment Systems 5. MENU: Press to access system settings such as display, brightness, clock mode, etc. 6. CD OPEN CLOSE: Press to open/close the display screen and access the CD player. Cold temperature advisory When operating the system below 32° Fahrenheit (0° Celsius), the display screen requires 20–30 minutes warm-up to achieve maximum brightness.
Page 43 Entertainment Systems 3. Select AM, FM1 or FM2. 4. Press TUNE to adjust manually up ( ) or down ( ) the frequency band. 5. Press SEEK to find the next strong station up ( ) or down ( Note: If PTY (program type) is selected, the station selection will be limited.
Page 44 Entertainment Systems To use the Navigation system: 1. Ensure that the vehicle ignition is on, and the navigation DVD is loaded into the navigation DVD player. Refer to Loading the map DVD for navigation DVD locations. 2. Press DEST. The warning screen will appear. After reading, press AGREE.
Page 45 Voice activated commands (if equipped) Your Lincoln Navigation System (LNS) may be equipped with a voice activated feature which allows you to “speak” certain commands to the system. Speaking clearly will help to ensure that the system correctly responds to your commands.
Page 46 • Restaurant • Hotel Audio mode Your Lincoln Navigation Audio System has many features including a full range of audio functions. To access these functions, press AUDIO on the main bezel. This will take you into audio mode. Volume/power control Press knob to turn the audio system on/off.
Page 47 To adjust the navigation voice output level, select the NAV MENU button via the map screen. Speed compensated volume (SCV) With this feature, radio volume changes automatically with vehicle speed to compensate for road and wind noise. To engage the SCV feature: 1.
Page 48 Entertainment Systems The AM/FM control works in radio, CD and navigation modes. AM/FM select in radio mode Press AM/FM1/FM2 to switch between AM/FM1/FM2 memory preset stations. AM/FM select in CD mode Press to stop CD play and begin radio play. AM/FM select in navigation mode The radio will continue to play in the background of the navigation screens.
Page 49 Entertainment Systems Bass : Allows you to increase or decrease the audio system’s bass output. Treble : Allows you to raise or lower the audio system’s treble output. Fade : Allows you to adjust sound between the front and rear speakers.
Page 50 Entertainment Systems Setting memory preset stations The radio is equipped with six station memory preset controls. These controls can be used to select up to six preset AM stations and twelve FM stations (six in FM1 and six in FM2). 1.
Page 51 Starting autoset memory preset 1. Select a frequency band using AM/FM1/FM2. 2. Press AUTO SET. 3. When the first six strong stations are filled, the station stored in memory preset control 1 will start playing. If there are less than six strong stations available on the frequency band, the remaining memory preset controls will all store the last strong station available.
Page 52 Entertainment Systems Radio data system (RDS) feature This feature allows your audio system to receive text information from RDS-equipped FM radio stations such as such as station call letters, program type, etc. When in FM mode, press RDS to activate/deactivate. Traffic function Select TRAFFIC for traffic information broadcast from certain...
Page 53 Ensure that the RDS function is turned on. Press PTY to turn the feature on/off. To set/change PTY: Ensure that the RDS function is turned on. Press SET PTY to select from the following program types: • All • Classical •...
Page 54 Entertainment Systems CD mode CD units are designed to play commercially pressed 12 cm (4.75 in) audio compact discs only. Due to technical incompatibility, certain recordable and re-recordable compact discs may not function correctly when used in Ford CD players. Irregular shaped CDs, CDs with a scratch protection film attached, and CDs with homemade paper (adhesive) labels should not be inserted into the CD player.
Page 55 Entertainment Systems 2. The navigation screen will fold down, allowing you access to the in-dash six CD system. 3. Press LOAD and the desired CD slot number. The indicator light will blink slowly at first, then quickly, signaling the system is ready. 4.
Page 56 Entertainment Systems Rewind/fast forward in CD mode Press to reverse or advance ) in the current CD track. Scan feature in CD mode Press SCAN to hear a brief sampling of all tracks on the current CD. Press again to disengage and remain with the current track.
Page 57 Entertainment Systems Pause In CD mode, press PAUSE to pause the current track. Press again to continue playing. Map mode Map display information To access the map display, press MAP on the bezel. Once pressed, the current map display will appear on the screen showing the current vehicle location.
Page 58 Entertainment Systems • touch one of the arrow buttons repeatedly for the map to be displayed again at the final zoom level. • touch one of the segments of the scale indicator for the map to be displayed at the selected zoom level. Additional map function buttons To initiate the display of additional map function buttons, tap the map...
Page 59 Entertainment Systems Screen symbols Navigation symbol — Indicates the current vehicle position and points to the direction in which the vehicle is currently traveling. Destination symbol — Indicates the current route destination. Next turn symbol — Shows the next maneuver that will need to be taken on the current route.
Page 60 Entertainment Systems Way point symbol — Indicates the location of a way point (locations you wish to visit in route to your ultimate destination) on the map. Home position symbol — Indicates the location on the map, currently stored as the home position. Stored location symbol —...
Page 61 Depending upon whether or not a route is active will determine if route options/route preferences is contained on the Navigation Menu. Route options (destination entered) Once in navigation mode and a route is currently active, press “Chng. route” to access the ROUTE OPTIONS screen.
Page 62 Entertainment Systems Route preferences After entering a destination, the Route options will appear on the screen showing what is currently selected. You may choose to activate/deactivate selections which the system will factor in when calculating your route. Those options are: •...
Page 63 Entertainment Systems Average speed settings Allows you to set approximate speeds you drive. These speeds enable the navigation system to aid in calculating timing for routes. Quick POI (Point of Interest) Allows you to change the Quick POI menu settings. Select the desired Quick POI (Gas, ATM, etc.) and then press ’List Categories’...
Page 64 Entertainment Systems Calibration This feature is helpful if the car has been towed, or if you notice it is not registering at the correct vehicle location on the map. Press “Position” to reposition the vehicle location. Press the screen to scroll the map to the desired location and press OK to confirm.
Page 65 Entertainment Systems • Time to destination (Show or Hide) Stored locations The Stored locations screen will allow you to choose from destinations that have been saved into the navigation system. In this screen, you can select from Memory Points, Special Memory Points, Home, Avoid Area, Destination and Way Point, or Previous Destination.
Page 66 Entertainment Systems On route scroll The system automatically scrolls through the entire planned navigation route either forwards or backwards. To activate, press the arrow buttons at the bottom left of the map screen. Voice guidance/volume Allows you to turn the voice guidance option on/off and to determine the volume level of the guidance voice prompts.
Page 67 Initial map display After pressing AGREE to the initial WARNING screen, you will move into the initial map screen which shows the current vehicle location. Pressing the globe icon will take you to the user settings — audible feedback, navigation units, language and clock.
Page 68 Entertainment Systems Ensure that you follow highway code restrictions and do not take any risks. For example, if you are unable to make a U-turn, continue on your journey. The navigation system will recalculate your route to get you back to an appropriate road to your destination. Destination entry Selecting a destination Press DEST to set a destination.
Page 69 Search area Your navigation system uses a regional search area. This area is the area from which navigational directions will be used. To check your area or reset, press CHANGE under the search area listing. The map will open and allow you to select another regional area.
Page 70 Entertainment Systems Deleting previous destination • Press “Delete”. The list of previous destinations is displayed showing “Delete Previous Destination” at the top of the screen. • Select (touch) the entry to be deleted. The item details will be listed. • Press YES to confirm the deletion.
Page 71 Adding a memory point • Once in the Store Memory Point Menu, press ADD. • Select (touch) the desired menu item. • Enter/select any required details. The new point will be added to the stored list of memory points. To give the new memory point a name: •...
Page 72 Entertainment Systems Choosing from the icon list After choosing ICON to edit, 15 normal and three audible icons will be displayed. Press the icon you wish to use. The normal icons will be displayed on the map to indicate the map location identified with that icon.
Page 73 Home To set home for the first time: VOL PUSH AUDIO DEST MENU CD OPEN • CLOSE • Press MAP. • Press “Nav. Menu”. • Press “Stored Locations.” • Press “Home”. • Press “Add”. Set home by selecting the correct address, POI, Previous destination, or selecting from the map.
Page 74 Entertainment Systems Adding a home location • Select the desired menu item you wish to set as Home (Address, Memory Point, Point of Interest, Previous Destination). • Enter the required details. • Press OK to set the home position. To view the set home position: From the stored locations menu with home selected, press LIST to view the location of the stored home position.
Page 75 Freeway Entrance/Exit Select “Freeway Entrance/Exit” from the second page of the Destination Entry menu. Follow these steps: 1. Enter freeway name— Enter the freeway name using the keyboard. Press “List” to select a freeway from those displayed. To enter numbers in the freeway name, press “Sym”.
Page 76 Entertainment Systems Special memory points There are five possible memory points that you can set. To set a memory point: • Press MAP. • Press “Nav Menu”. • Press “Stored locations”. • Press “Special Memory Point”. • Select “Add” and input destination. •...
Page 77 Adding (storing) a destination or way point • Once a destination is entered, press ADD to store the location. The Store Dest. & Way Point menu is displayed. • Select whether you want to store an Address, Point of Interest or Previous Destination.
Page 78 Entertainment Systems Editing and changing order of way points and destination Press “Chg. Order” to change the order in which the way points are visited. The points are listed chronologically from bottom up, the destination being on the top. Press the MAP button to edit the way point location on the map display.
Page 79 Entertainment Systems Route calculation Once the route criteria is selected, the navigation system automatically calculates the selected destination. The route appears on the display screen and a voice prompt provides instructions. The system may calculate up to four routes for the desired destination. Press “Next”...
Page 80 Entertainment Systems Route interruptions In the course of your destination, you may decide to temporarily leave your planned route for gas, food, etc. If you turn off the ignition, the option to continue the route guidance will be displayed when the ignition is turned on again.
Page 81 Listing areas to avoid You can list all areas noted as “avoid”. • Press “Nav Menu”. • Press “Stored locations”. • Press “Avoid area”. • Press LIST to view all previously stored selections. • Select the desired one. The map screen will be displayed, showing the location and address of the selected area.
Page 82 To access menu mode, press the MENU hard control. Menu mode allows you to access: • System Set-up • Information — Gives you the Lincoln Customer Assistance Center information. • Brightness/Contrast — Allows you to adjust the brightness and contrast on the screen.
Page 83 • Screen off — Allows you to turn off the navigation screen. System setup The system set up menu contains the following user settings: • Audible Feedback — Press to activate audible voice navigation commands. Press again to deactivate. • Navigation Units — Press to toggle between Metric/English units.
Page 84 Once in Menu mode, press CLOCK to set the hours/minutes. DVD interaction (if equipped) Your vehicle may be equipped with a DVD player. Your Lincoln Navigation System (LNS) will interact with your DVD player, providing you access and messages to the status of the system.
Page 85 Entertainment Systems At any time, you may say these commands: • AM • FM1 • FM2 • CD • DVD (if equipped) During normal radio operation, you may say: • Seek up • Seek down During CD play with the in-dash 6 disc player: •...
Page 86 Entertainment Systems Wireless headphones Your system is equipped with 2 sets of wireless headphones. (Two AAA batteries are needed to operate the headphones.) Batteries are included. To install the batteries, lightly press down on the top of the left earpiece and slide the cover off.
Page 87 Do not attempt to service, repair or modify the system. See your Ford or Lincoln Mercury dealer. The driver must not attempt to operate any detailed operation of the navigation system while the vehicle is in motion. Give full attention to driving and to the road.
Page 88 Ford or Lincoln Dealer. Federal Communication Commission (FCC) Compliance Changes or modifications not approved by Ford Lincoln Mercury could void user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Page 89 Radio reception factors There are certain factors that may effect your radio reception. • Distance/strength. The further an FM signal travels, the weaker it is. The listenable range of the average FM station is approximately 40 km (24 miles). This range can be affected by “signal modulation.” Signal modulation is a process radio stations use to increase their strength/volume relative to other stations.
Page 90 Entertainment Systems Ensure that you do not have any metal objects on the rear parcel shelf and that if your windows are tinted, they use non-metal tinting instead of metal oxide tinting. Both of these factors can also interrupt GPS reception.
Page 91 Entertainment Systems Latest map DVDs The map content is constantly changing due to new roads, traffic restrictions, etc. . Therefore, it is not always possible to exactly match the DVD map with the current roadways. For best results, always use the latest version of the map DVD.
Page 92: Climate Controls
Climate Controls DUAL AUTOMATIC TEMPERATURE CONTROL (DATC) SYSTEM 1. A/C control 2. Recirculated air control 3. Passenger temperature control 4. Rear defrost control 5. DUAL control 6. Defrost control 7. Floor & Defrost control 8. Floor control The DATC system will maintain a selected temperature setting and automatically control the fan speed and airflow location.
Page 93 Climate Controls Automatic operation Press AUTO and select the desired temperature. The system will either heat or cool the vehicle to achieve the selected temperature. The system will automatically determine fan speed, airflow location and whether outside or recirculated air is required.
Page 94 Climate Controls Temperature conversion Press the Fahrenheit/Celsius (°F /°C) control to switch between Fahrenheit and Celsius. Displaying outside temperature Press Ext to display the outside temperature. The outside temperature will be displayed until Ext has been pressed again. If the interior temperature or fan speed are adjusted or a manual override is selected while the outside temperature is being displayed, the new temperature, fan speed or override control will appear in the display window for four seconds, the outside temperature will then return to the...
Page 95 Climate Controls Fan speed ( When in automatic operation, fan speed operates as necessary to achieve the selected temperature. If desired, the fan speed can be adjusted manually through the use of the fan speed control. • A/C control (air conditioning) — Used to manually enable or disable air conditioning in all modes except Defrost.
Page 96: Recirculated Air
Climate Controls • Recirculated air (recirculated air) — Used to manually enable or disable the operation of recirculated air in all modes except Defrost. When the air conditioning is operating, recirculated air helps to reduce the amount of time required to cool the inside of the vehicle.
Page 97 • Off-Outside air is shut out and the fan will not operate. This mode will reduce undesirable odors from entering the vehicle but may increase the possibility of interior window fogging. • Panel - Distributes outside or recirculated air through the instrument panel registers.
Page 98 Climate Controls • Do not place objects under the front seat or over the defroster ducts. They may reduce visibility, fall into the ducts, or degrade the performance of your climate control system. Do not place objects on top of the instrument panel, as these objects may become projectiles in a collision or sudden stop.
Page 99 Climate Controls Controls the direction of the airflow in the rear of the vehicle. When Floor is selected, airflow will be directed through the floor registers. When Panel is selected, airflow is directed through the overhead registers. Press the mode selector once to select air distribution through the overhead vents.
Page 100 Climate Controls AIRFLOW CONTROL Controls whether airflow will or will not be distributed through the floor console. To select airflow from the registers of the floor console, slide the airflow control to the top. To select no airflow from the registers of the floor console, slide the airflow control to the bottom.
Page 101: Lights
HEADLAMP CONTROL Rotate the headlamp control clockwise to the first position to turn on the parking lamps. Rotate clockwise to the second position to also turn on the headlamps. Foglamp control The headlamp control also operates the foglamps. The foglamps can be turned on only when the headlamp control is in the position and the high beams are not...
Page 102 Lights Autolamp exit time delay, manual sequence This option allows you to change the length of the autolamp exit delay. To program the auto lamp exit time delay: 1. Start with the ignition in OFF and the autolamps selected. 2. Deselect the auto lamps. 3.
Page 103 • Press the setup button - The message center then displays the next menu selection in its list. (6) • Press the reset button - The message center then proceeds to the next sequence/step (3) below. • The message center sends/issues the “Autolamp Delay Command” to the body security module (BSM).
Page 104 Lights Flash to pass Pull toward you slightly to activate and release to deactivate. PANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel and all applicable switches in the vehicle during headlamp and parklamp operation. Move the control to the full upright position, past detent, to turn on the interior lamps.
Page 105 Lights 2. VOR: Measure the height from the center of your headlamp to the ground and mark a 2.4 meter (8 foot) horizontal reference line on the vertical wall or screen at this height (a piece of masking tape works well). The center of the lamp is marked by a 3.0 mm circle on the headlamp lens.
Page 106: Turn Signal Control
Lights TURN SIGNAL CONTROL • Push down to activate the left turn signal. • Push up to activate the right turn signal. • Turn signal will shut off headlamps, in DRL equipped vehicles, in daytime driving. INTERIOR LAMPS Front row map lights (if equipped) To turn on the map lights, press the edge of the light.
Page 107: Bulb Replacement
Third row courtesy/reading/cargo lamps The dome portion of the lamp, the center light, can be turned on when the headlamp control is rotated fully up or when an door is opened. With the ignition key in the ACC or ON position, the rear dome lamp can be turned ON or OFF by sliding the control.
Page 108 Lights Function Number of bulbs Fog lamp Liftgate lamp High-mount stop lamp Rear license plate lamp Mirror turn signal lamp Approach lamp Cargo lamp Interior overhead lamp Map lamps Front footwell light All replacement bulbs are clear in color except where noted. To replace all instrument panel lights see your dealer.
Page 109 Replacing headlamp bulbs To remove the headlamps from the vehicle to change the HIGH BEAM bulb: 1. Make sure the headlamp switch is in the OFF position, then open the hood. 2. Remove the plastic radiator cover over the headlamps by grasping the rear edge of the cover and pulling up and toward you.
Page 110 Lights 1. Push the bulb straight in, carefully aligning the plastic tabs in the base of the bulb with the openings in the plastic ring. 2. Rotate the bulb clockwise until it stops. 3. Reconnect the electrical connector to the bulb. 4.
Page 111 Lights Replacing front parking lamp/turn signal/sidemarker bulbs To remove the headlamps from the vehicle and to change the front turn signal lamp bulbs: 1. Make sure the headlamp switch is in the OFF position, then open the hood. 2. Remove the plastic radiator cover over the headlamps by grasping the rear edge of the cover and pulling up and toward you.
Page 112 Lights 2. Carefully pull the bulb straight out of the socket and push in the new bulb. 3. Install the bulb socket in the lamp assembly by turning it counterclockwise. To re-install the headlamp on the vehicle: 1. Install the headlamp on the vehicle by aligning the four plastic projections into the four holes, pushing rearward to seat the lamp assembly.
Page 113 Lights Replacing liftgate tail lamp bulb 1. Make sure the headlamp switch is in the OFF position and then open the liftgate to expose the fasteners. 2. Remove the two acorn nuts from the lamp assembly. 3. Pull the lamp off by pulling rearward on the lamp.
Page 114 Lights Replacing license plate lamp bulbs 1. Make sure the headlamp switch is in the OFF position, then remove the screw and pry the license plate lamp lens down. 2. Pull down the lens assembly and rotate the lens counterclockwise. 3.
Page 115 Lights Approach lamp/mirror turn signal bulb removal To change the bulbs: 1. Make sure the headlamp switch is in the OFF position. 2. Remove the approach lamp/turn signal lens from the mirror housing using a standard flat screwdriver to pry the lamp assembly out. 3.
Page 116: Driver Controls
Driver Controls WINDSHIELD WIPER/WASHER CONTROLS Rotate the windshield wiper control to the desired interval, low or high speed position. INT1 The bars of varying length are for intermittent wipers. When in this position rotate the control upward for fast intervals and downward for slow intervals.
Page 117 Driver Controls Changing the wiper blades It is recommended that wiper blades are renewed before winter. To replace the wiper blades: 1. Fold back the wiper arm and position the wiper blade at right angles to the wiper arm. 2. To remove, press the retaining clip (A) to disengage the wiper blade, then pull the blade down toward the windshield to remove it...
Page 118 Driver Controls While holding the steering wheel, find the nearest gear mesh point and pull the lever up to its original position to lock the steering column. Never adjust the steering column when the vehicle is moving. ILLUMINATED VISOR MIRROR Lift the mirror cover to turn on the visor mirror lamps.
Page 119 Moon roof (if equipped) You can move the glass panel of the moon roof back to open or tilt up to ventilate the vehicle. To open the moon roof: The moon roof is equipped with an automatic, one-touch, express opening feature. Press and momentarily hold the rear portion of the control.
Page 120 Driver Controls CLOCK Press the right control to increase the time displayed. Press the left control to decrease the time displayed. AUXILIARY POWER POINT (IF EQUIPPED) Power outlets are designed for accessory plugs only. Do not hang any type of accessory or accessory bracket from the plug. Improper use of the power outlet can cause damage not covered by your warranty.
Page 121: Power Windows
Another auxiliary power point is located on the right rear quarter panel. The power point is accessible from the liftgate. The maximum current draw of any single power point should not exceed it’s fuse rating, otherwise this will result in a blown fuse. Do not use the cigarette/cigar lighter element in any power point.
Page 122 Driver Controls The following views are the driver’s side switches: Normal operation • Push down (to the first detent) and hold the top portion of the switch to open. • Pull up (to the first detent) and hold the top portion of the switch to close.
Page 123 One touch up or down This feature is present on the driver’s window only. To operate ONE TOUCH DOWN: • Press the switch completely down to the second detent and release quickly. The driver’s window will open fully. Momentarily press the switch to any position to stop the window operation.
Page 124: Mirrors
Driver Controls up with no bounce-back protection. If the switch is released before the window reaches fully closed or the ignition is turned OFF (without accessory delay being active), the window will stop. Security override can be used if there is ice on the window or seals, causing a restriction. Window lock The window lock feature allows only the driver to operate the rear power...
Page 125 Driver Controls Press the control to turn the mirror OFF or AUTO. The mirror will automatically return to the normal state whenever the vehicle is placed in R (Reverse)(when the mirror is on) to ensure a clear view when backing Power side view mirrors The ignition must be in the ACC or ON position to adjust the power side view mirrors.
Page 126 Driver Controls Heated outside mirrors Both mirrors are heated automatically to remove ice, mist and fog when the rear window defrost is activated. Do not remove ice from the mirrors with a scraper or attempt to readjust the mirror glass if it is frozen in place. These actions could cause damage to the glass and mirrors.
Page 127 Reverse tilt down mirrors The side mirrors tilt down when the vehicle is put in R (Reverse). The reverse mirror feature can be turned ON and OFF through the Message Center in this chapter or by using the following key sequence. This procedure must be performed within 20 seconds.
Page 128: Speed Control
Driver Controls SPEED CONTROL To turn speed control on • Press ON. Vehicle speed cannot be controlled until the vehicle is traveling at or above 48 km/h (30 mph). Do not shift the gearshift lever into N (Neutral) with the speed control on.
Page 129 To set a speed • Press SET+. For speed control to operate, the speed control must be ON and the vehicle speed must be greater than 48 km/h (30 mph). If you drive up or down a steep hill, your vehicle speed may vary momentarily slower or faster than the set speed.
Page 130 Driver Controls To set a lower set speed • Press and hold SET −. Release the control when the desired speed is reached or • Press and release SET − to operate the Tap-Down function. Each press will decrease the set speed by 1.6 km/h (1 mph) or •...
Page 131 Driver Controls To disengage speed control • Press CNCL, or • depress the brake pedal. Disengaging the speed control will not erase the previously programmed set speed. Pressing OFF will erase the previously programmed set speed. 2003 Aviator f/k/a Navigator LS (231) Owners Guide (post-2002-fmt) USA English (fus)
Page 132 Driver Controls To return to a previously set speed • Press RES. For RES to operate, the vehicle speed must be faster than 48 km/h (30 mph). Indicator light This light comes on when the vehicle speed control is engaged and actively controlling vehicle speed.
Page 133 In AM, FM1, or FM2 mode: • Press MEM to select preset stations within the selected radio band. In Tape mode: • Press MEM to select the next selection on the tape. In CD mode: • Press MEM to select the next selection on the CD.
Page 134 Driver Controls Press FAN + or - to adjust fan speed. Navigation steering wheel controls (if equipped) These controls allow you to operate some audio and navigation control features when the vehicle is equipped with the navigation feature. Audio control features Press to select: •...
Page 135 Driver Controls Navigation control features Press and hold VOICE until the voice icon appears to use the navigation voice guidance. Press RPT (REPEAT) control to hear previous command repeated from the navigation system. Climate control features Press TEMP + or - to adjust temperature.
Page 136 Driver Controls When programming your HomeLink Wireless Control System to a garage door or gate, be sure that people and objects are out of the way to prevent potential harm or damage. Do not use the HomeLink Wireless Control System with any garage door opener that lacks safety stop and reverse features as required by U.S.
Page 137 Driver Controls 3. Simultaneously press and hold both the HomeLink and hand-held transmitter button. Do not release the buttons until step 4 has been completed. Some entry gates and garage door openers may require you to replace step 3 with procedures noted in the “Gate Operator and Canadian Programming”...
Page 138 Driver Controls Operating the HomeLink Wireless Control System To operate, simply press and release the appropriate HomeLink button. Activation will now occur for the trained product (garage door, gate operator, security system, entry door lock, or home or office lighting etc.).
Page 139: Message Center
Gate Operator & Canadian Programming During programming, your hand-held transmitter may automatically stop transmitting — not allowing enough time for HomeLink to accept the signal from the hand-held transmitter. After completing steps 1 and 2 outlined in the “Programming” section, replace step 3 with the following: Note: If programming a garage door opener or gate operator, it is advised to unplug the device during the “cycling”...
Page 140 Driver Controls Selectable features Reset Press this control to select and reset functions shown in the INFO menu and SETUP menu. Info menu This control displays the following control displays: • Odometer/Compass • Trip odometer/Odometer/Compass • Distance to Empty • Average Fuel Economy •...
Page 141 For optimum calibration, turn off all electrical accessories (heater/air conditioning, wipers, etc.) and make sure all vehicle doors are shut. 1. Turn ignition to the ON position. 2. Start the engine. 3. Determine your magnetic zone by referring to the zone map. 4.
Page 142 Driver Controls Average fuel economy (AFE) Select this function from the INFO menu to display your average fuel economy in liters/100 km or miles/gallon. If you calculate your average fuel economy by dividing liters of fuel used by 100 kilometers traveled (miles traveled by gallons used), your figure may be different than displayed for the following reasons: •...
Page 143 Driver Controls The DTE function will display LOW FUEL LEVEL and sound a tone for one second when you have approximately 80 km (50 miles) to empty. If you RESET this warning message, this display and tone will return within 10 minutes. DTE is calculated using a running average fuel economy, which is based on your recent driving history of 800 km (500miles).
Page 144 Driver Controls The sequence of the system check report and how it appears in the message center is as follows: 1. FUEL LEVEL 2. WASHER FLUID LEVEL 3. OIL LIFE IN XX% 4. PARK ASSIST 5. ENGINE TEMP 6. OIL PRESSURE 7.
Page 145 Driver Controls Reverse mirrors 1. Select this function from the SETUP control for the current display mode. 2. Press the RESET control to turn the reverse mirrors ON or OFF. Autolamp delay 1. Select this function from the SETUP control for the current display mode.
Page 146 Driver Controls 2. Pressing the RESET control cycles the message center through each of the language choices. 3. Press and hold the RESET control to set the language choice. AWD locked (vehicles equipped with AdvanceTrac only) Select this function from the SETUP menu to display the AWD locked function.
Page 147 This acts as a reminder that these warning conditions still exist within the vehicle. Warning display Check park assist AdvTrac ON (if equipped) AdvTrac OFF (if equipped) Change Oil Soon Temporary AWD locked (vehicles equipped with AdvanceTrac AWD lock OFF AWD auto ON (vehicles equipped with AdvanceTrac Warning-tire very low (if equipped) Tire pressure system fault (if equipped)
Page 148 Driver Controls Warning display Low washer fluid level Check AdvTrac (if equipped) Check AWD (vehicles equipped with AdvanceTrac only) AWD Disabled (vehicles equipped with AdvanceTrac only) Check fuel cap Oil change required CHECK PARK ASSIST. Displayed when the transmission is in R (Reverse) and the park assist does not operate properly.
Page 149 Driver Controls AWD DISABLED LOCKED (vehicles equipped with AdvanceTrac only). Displayed when the AWD system begins to overheat placing itself in the autolock mode. If the warning stays on or continues to come on, contact your dealer as soon as safely possible. WARNING-TIRE VERY LOW (if equipped).
Page 150 Driver Controls driving, when driving in a low gear at a high speed for an extended period of time or due to a loss of transmission fluid. Stop the vehicle as soon as safely possible, place the shift lever into P (Park) or N (Neutral) and raise the engine RPM.
Page 151 Driver Controls To reset the oil monitoring system to 100% after each oil change [approximately 8,000 km (5,000 miles) or 180 days] perform the following: 1. Select this function from the SETUP control for current display mode. 2. Press and release the RESET control to display “HOLD RESET TO CONFIRM”.
Page 152 Driver Controls DATA ERR. These messages indicate improper operation of the vehicle network communication between electronic modules. • Fuel computer • Oil life • Charging system • Door sensor • Washer fluid • Brake fluid • Compass • Outside temperature •...
Page 153 such equipment. Mobile Communications can enhance personal safety and security when appropriately used, particularly in emergency situations. Safety must be paramount when using mobile communications equipment to avoid negating these benefits. Mobile Communication Equipment includes, but is not limited to cellular phones, pagers, portable email devices, in vehicle communications systems, telematics devices and portable two-way radios.
Page 154 Driver Controls POSITIVE RETENTION FLOOR MAT Position the driver floor mat so that the eyelet is over the pointed end of the retention post and rotate forward to lock in. Make sure that the mat does not interfere with the operation of the accelerator or the brake pedal.
Page 155 Always close liftgate window before opening liftgate. Liftgate glass and liftgate should never be open at the same time. Failure to observe this warning may result in personal injury or damage to your vehicle. Make sure the liftgate door and/or window are closed to prevent exhaust fumes from being drawn into the vehicle.
Page 156 Driver Controls Vehicles with a higher center of gravity such as utility and four-wheel drive vehicles handle differently than vehicles with a lower center of gravity. Utility and four-wheel drive vehicles are not designed for cornering at speeds as high as passenger cars any more than low-slung sport cars are designed to perform satisfactorily under off-road conditions.
Page 157: Locks And Security
Locks and Security KEYS The key operates all locks on your vehicle. In case of loss, replacement keys are available from your dealer. You should always carry a second key with you in a safe place in case you require it in an emergency. Refer to SecuriLock Passive Anti-Theft System for more information.
Page 158 Locks and Security Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. The remote entry system allows you to lock or unlock all vehicle doors and liftgate and open the liftgate window without a key. The remote entry lock/unlock feature operates in any ignition position.
Page 159 Locks and Security Opening the liftgate window Press the control to unlatch the liftgate window. Sounding a panic alarm Press this control to activate the alarm. The personal panic alarm will cycle the horn and parking lamps on/off. To deactivate the alarm, press the control again or turn the ignition to Memory seat feature The remote entry system can also...
Page 160 Locks and Security Associating the transmitter with the memory seat feature To activate this feature: 1. Select the desired memory position by pressing the memory 1 or 2 button on the memory SET control, located on the instrument panel to the left of the steering wheel.
Page 161 To replace the battery: 1. Twist a thin coin between the two halves of the transmitter near the key ring. DO NOT TAKE THE FRONT PART OF THE TRANSMITTER APART. 2. Place the positive (+) side of new battery in the same orientation. Refer to the diagram inside the transmitter unit.
Page 162 Locks and Security Programming remote transmitters It is necessary to have all (maximum of four — original and/or new) of your remote transmitters available prior to beginning this procedure. To program the transmitters yourself: 1. Ensure the vehicle is electronically unlocked. 2.
Page 163 Locks and Security Illuminated entry The interior lamps illuminate when the remote entry system is used to unlock the door(s). The system automatically turns off after 25 seconds or when the ignition is turned to the ON or ACC position. The dome lamp control (if equipped) must not be set to the OFF position for the illuminated entry system to operate.
Page 164 Locks and Security Deactivating/activating the autolock feature The autolock feature may be deactivated/activated by selecting the autolock function (accessed by pressing the SETUP control). Press the RESET control to turn the autolock function ON or OFF. Refer to Message center in the Driver controls chapter for additional information.
Page 165 Locks and Security Programming your own personal entry code To program your own code: 1. Enter factory set code (keypad will illuminate when pressed). 2. Press 1/2 control within five seconds of step 1. 3. Enter your personal 5 digit code. Enter each digit within five seconds of previous one.
Page 166 Locks and Security Anti-scan feature The anti-scan feature prevents repeated attempts at arriving at a valid key code. The keyless entry pad is disabled for 1 minute after 7 unsuccessful attempts at entering a valid key code. The keypad will flash during this 1 minute mode.
Page 167 Locking the doors with the keyless entry system It is not necessary to enter the factory or personal code prior to locking all doors. To lock the doors: • with the driver’s door closed, press the 7/8 control and the 9/0 control at the same time.
Page 168 Locks and Security The SecuriLock passive anti-theft system is not compatible with non-Ford aftermarket remote start systems. Use of these systems may result in vehicle starting problems and a loss of security protection. THEFT INDICATOR The theft indicator is the flashing red indicator located on the dash panel.
Page 169 OFF and restart the engine with all other objects on the key ring held away from the ignition key. Check to make sure the coded key is an approved Lincoln coded key. If your keys are lost or stolen you will need to do the following: •...
Page 170 Locks and Security 1. Insert the first previously programmed coded key into the ignition and turn the ignition from 1 (OFF) to 3 (ON) (maintain ignition in 3 (ON) for at least one second, but no more than ten seconds). 2.
Page 171 The system is ready to arm whenever the key is removed from the ignition. Any of the following actions will prearm the alarm system: • Open any door, liftgate or liftgate window and press the power door lock control to lock the doors. •...
Page 172 Locks and Security Disarming the system You can disarm the system by any of the following actions: • Unlock the doors by using your remote entry transmitter. • Unlock the doors by using your keyless entry pad. • Unlock the driver’s door with a key. Turn the key full travel (toward the front of the vehicle) to make sure the alarm disarms.
Page 173 • Press the PANIC control on the remote entry transmitter. This will only shut off the horn and parking lamps when the alarm is sounding. The alarm system will still be armed. • Press the liftgate window control on the remote entry transmitter. The liftgate and liftgate window are no longer armed, but the doors and hood are still armed.
Page 174: Seating And Safety Restraints
Seating and Safety Restraints SEATING Adjustable head restraints Your vehicle’s seats may be equipped with head restraints which are vertically adjustable. The purpose of these head restraints is to help limit head motion in the event of a rear collision. To properly adjust your head restraints, lift the head restraint so that it is located directly behind your head or as close to that position as possible.
Page 175 Seating and Safety Restraints Using the power lumbar support The power lumbar control is located on the door panel. Press one side of the control to adjust firmness. Press the other side of the control to adjust softness. Using the manual recline function Never adjust the driver’s seat or seatback when the vehicle is moving.
Page 176 Seating and Safety Restraints Adjusting the power front seats – door mounted controls The controls for the power seats are located on the inside of each front door. Never adjust the driver’s seat or seatback when the vehicle is moving. Do not pile cargo higher than the seatbacks to avoid injuring people in a collision or sudden stop.
Page 177 Seating and Safety Restraints Press to move the rear portion of the seat cushion up or down. Memory seats/rearview mirrors/adjustable pedals This system allows automatic positioning of the driver seat, outside rearview mirrors, and adjustable pedals to two programmable positions. The memory seat control is located on the instrument panel to the left of the steering wheel.
Page 178 Seating and Safety Restraints Deactivating/activating the easy entry/exit feature The easy entry/exit feature may also be turned on and off using the following key sequence. This procedure must be performed within 20 seconds. 1. Remove the key from the ignition (if currently inserted). 2.
Page 179 Seating and Safety Restraints In heat mode: • Rotate the thumbwheel to select the desired heat level from 1 (MIN) to 5 (MAX). In cool mode: • Rotate the thumbwheel to select the desired cooling level from 1 (MIN) to 5 (MAX). When setting 1 is selected, the seat(s) will provide vent cooling only (same temperature as cabin air).
Page 180 Seating and Safety Restraints To remove climate controlled seat air filter: • Remove key from ignition. • Push on the outside rigid edge of the air filter at the center and rotate toward the front of the vehicle once tabs are released. •...
Page 181 Seating and Safety Restraints The head restraints can be raised by lifting. If the head restraint is fully lowered, press the release button to raise it. To raise or lower the head restraint, press the release button located on the side of the metal bar. If the head restraint becomes detached, replace the notched bar into the holes while holding the release button.
Page 182 Seating and Safety Restraints To return the seat to the upright position: 1. Pull the handle down to release the lock position and lift the seatback toward the rear of the vehicle. 2. Rotate the seatback until you hear a click, locking it in the upright position.
Page 183 Seating and Safety Restraints 3. To return the seat to a seating position, flip the seat into the upright position. 4. Make sure the seat is latched to the floor. If the seat is not firmly latched to the floor, the seat back will not lock in the upright position.
Page 184 Seating and Safety Restraints Folding the middle 2nd row seat (If equipped) 1. Locate the lever on the top of the seatback. 2. Pull the lever up and push the seatback toward the front of the vehicle. 3. Press down on the top outboard area of the seatback until a click is heard.
Page 185 Seating and Safety Restraints To put seat in stowed position: 1. Pull the seat release lever located on top of the seatback while pushing the seatback down onto the seat cushion. 2. The seatback will latch into place. 3. Push the closeout panel forward over the space between the seats.
Page 186: Safety Restraints
Seating and Safety Restraints 2. Pull the seat release lever located on top of the seatback while lifting the seatback into the upright position. 3. The seatback will latch into place. The third row seat is equipped with combination lap and shoulder belts in both seating positions.
Page 187 Seating and Safety Restraints In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a safety belt. Each seating position in your vehicle has a specific safety belt assembly which is made up of one buckle and one tongue that are designed to be used as a pair.
Page 188 Seating and Safety Restraints • Front and rear seats All safety restraints in the vehicle are combination lap and shoulder belts. All of the passenger combination lap and shoulder belts have two types of locking modes described below: Vehicle sensitive mode This is the normal retractor mode, which allows free shoulder belt length adjustment to your movements and locking in response to vehicle movement.
Page 189 Seating and Safety Restraints How to use the automatic locking mode 1. Buckle the combination lap and shoulder belt. 2. Grasp the shoulder portion and pull downward until the entire belt is pulled out. 3. Allow the belt to retract. As the belt retracts, you will hear a clicking sound.
Page 190 Seating and Safety Restraints BELT AND RETRACTOR ASSEMBLY MUST BE REPLACED if the safety belt assembly “automatic locking retractor” feature or any other safety belt function is not operating properly. In addition, all safety belts should be checked for proper function. Failure to replace the belt and retractor assembly could increase the risk of injury in collisions.
Page 191 Seating and Safety Restraints Front and second row safety belt height adjustment Your vehicle has safety belt height adjustments for the driver, right front passenger and second row outboard passengers. Adjust the height of the shoulder belt so the belt rests across the middle of your shoulder.
Page 192 Seating and Safety Restraints BeltMinder The BeltMinder feature is a supplemental warning to the safety belt warning function. This feature provides additional reminders to the driver that the driver’s safety belt is unbuckled by intermittently sounding a chime and illuminating the safety belt warning lamp in the instrument cluster.
Page 193 Seating and Safety Restraints Reasons given... “Belts are uncomfortable” “I was in a hurry” “Safety belts don’t work” “Traffic is light” “Belts wrinkle my clothes” “The people I’m with don’t wear belts” “I have an air bag” “I’d rather be thrown clear” 2003 Aviator f/k/a Navigator LS (231) Owners Guide (post-2002-fmt) USA English (fus)
Page 194 Seating and Safety Restraints Do not sit on top of a buckled safety belt to avoid the Belt Minder chime. Sitting on the safety belt will increase the risk of injury in an accident. To disable (one-time) or deactivate the Belt Minder feature please follow the directions stated below.
Page 195 Seating and Safety Restraints 5. Buckle then unbuckle the safety belt three times, ending with the safety belt unbuckled. • After step 5 the safety belt warning light will be turned on for three seconds. 6. Within seven seconds of the safety belt warning light turning off, buckle then unbuckle the safety belt.
Page 196: Air Bags
Seating and Safety Restraints recommends that all safety belt assemblies used in vehicles involved in a collision be replaced. However, if the collision was minor and a qualified technician finds that the belts do not show damage and continue to operate properly, they do not need to be replaced.
Page 197 Do not attempt to service, repair, or modify the air bag supplemental restraint systems or its fuses. See your Ford or Lincoln Mercury dealer. Modifying or adding equipment to the front end of the vehicle (including frame, bumper, front end body structure and tow hooks) may affect the performance of the air bag system, increasing the risk of injury.
Page 198 Seating and Safety Restraints Children and air bags Children must always be properly restrained. Accident statistics suggest that children are safer when properly restrained in the rear seating positions than in the front seating position. Failure to follow these instructions may increase the risk of injury in a collision.
Page 199 Seating and Safety Restraints The air bags inflate and deflate rapidly upon activation. After air bag deployment, it is normal to notice a smoke-like, powdery residue or smell the burnt propellant. This may consist of cornstarch, talcum powder (to lubricate the bag) or sodium compounds (e.g., baking soda) that result from the combustion process that inflates the...
Page 200 Do not attempt to service, repair, or modify the Safety Canopy system, its fuses, the A, B, or C pillar trim, or the headliner on a vehicle containing a Safety Canopy . See your Ford or Lincoln Mercury dealer. All occupants of the vehicle including the driver should always...
Page 201 Seating and Safety Restraints How does the Safety Canopy The design and development of the Safety Canopy system included recommended testing procedures that were developed by a group of automotive safety experts known as the Side Airbag Technical Working Group. These recommended testing procedures help reduce the risk of injuries related to the deployment of side airbags (including the Safety...
Page 202 Seating and Safety Restraints The Safety Canopy is mounted to the roof side-rail sheet metal, behind the headliner, above the first and second row seats. In certain lateral collisions or rollover events, the Safety Canopy activated, regardless of which seats are occupied. The Safety Canopy designed to inflate between the side window area and occupants to further enhance protection provided in side impact collisions and rollover events.
Page 203: Child Restraints
Seating and Safety Restraints Any difficulty with the system is indicated by one or more of the following: • The readiness light (same light as for front air bag system) will either flash or stay lit. • The readiness light will not illuminate immediately after ignition is turned on.
Page 204 Seating and Safety Restraints Children and safety belts If the child is the proper size, restrain the child in a safety seat. Children who are too large for child safety seats (as specified by your child safety seat manufacturer) should always wear safety belts. Follow all the important safety restraint and air bag precautions that apply to adult passengers in your vehicle.
Page 205 Seating and Safety Restraints Booster seats should be used until you can answer YES to ALL of these questions: • Can the child sit all the way back against the vehicle seat back with knees bent comfortably at the edge of the seat without slouching? •...
Page 206 Seating and Safety Restraints The shoulder belt should cross the chest, resting snugly on the center of the shoulder. The lap belt should rest low and snug across the hips, never up high across the stomach. If the booster seat slides on the vehicle seat, placing a rubberized mesh sold as shelf or carpet liner under the booster seat may improve this condition.
Page 207 Seating and Safety Restraints When installing a child safety seat: • Review and follow the information presented in the Air bag supplemental restraint system (SRS) section in this chapter. • Use the correct safety belt buckle for that seating position (the buckle closest to the direction the tongue is coming from).
Page 208 Seating and Safety Restraints Installing child safety seats with combination lap and shoulder belts Air bags can kill or injure a child in a child seat. NEVER place a rear-facing child seat in front of an active air bag. If you must use a forward-facing child seat in the front seat, move the seat all the way back.
Page 209 Seating and Safety Restraints 3. While holding the shoulder and lap belt portions together, route the tongue through the child seat according to the child seat manufacturer’s instructions. Be sure the belt webbing is not twisted. 4. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) for that seating position until...
Page 210 Seating and Safety Restraints 7. Pull the lap belt portion across the child seat toward the buckle and pull up on the shoulder belt while pushing down with your knee on the child seat. 8. Allow the safety belt to retract to remove any slack in the belt.
Page 211 Seating and Safety Restraints • 40/20/40 second row seats • second row bucket seats Attach the tether strap only to the appropriate tether anchor as shown. The tether strap may not work properly if attached somewhere other than the correct tether anchor. 1.
Page 212 Seating and Safety Restraints • At the rear of the cargo area 4. Clip the tether strap to the anchor. If the tether strap is clipped incorrectly, the child safety seat may not be retained properly in the event of a collision. 5.
Page 213 Seating and Safety Restraints Attaching safety seats with LATCH (Lower Anchors and Tethers for Children) attachments for child seat anchors Some child safety seats have two rigid or webbing mounted attachments that connect to two anchors at certain seating positions in your vehicle. This type of child seat eliminates the need to use seat belts to attach the child seat.
Page 214 Follow the child seat manufacturer’s instructions to properly install a child seat with LATCH attachments. Two plastic LATCH guides may be obtained at no charge from any Ford or Lincoln Mercury dealer. They snap onto the latch lower anchor in the vehicle to help attach a child seat with rigid latch attachments.
Page 215: Driving
STARTING Positions of the ignition 1. OFF/LOCK, shuts off the engine and all accessories/locks the steering wheel, gearshift lever and allows key removal. 2. ACC, allows the electrical accessories such as the radio to operate while the engine is not running.
Page 216 Driving If you smell exhaust fumes inside your vehicle, have your dealer inspect your vehicle immediately. Do not drive if you smell exhaust fumes. Important safety precautions A computer system controls the engine’s idle revolutions per minute (RPM). When the engine starts, the idle RPM runs higher than normal in order to warm the engine.
Page 217 3. Turn the key to 3 (ON) without turning the key to 4 (START). Make sure the corresponding lights illuminate or illuminate briefly. If a light fails to illuminate, have the vehicle serviced. • If the driver’s safety belt is fastened, the Starting the engine Note: Whenever you start your vehicle, release the key as soon as the engine starts.
Page 218: Brakes
Driving try again. If the engine does not start in two attempts, press the accelerator pedal all the way to floor and hold. Turn the key to START position. 4. When the engine starts, release the key, then release the accelerator pedal gradually as the engine speeds up.
Page 219 squeal or groan noises when the brakes are applied. Such noises are usually heard during the first few brake applications in the morning; however, they may be heard at any time while braking and can be aggravated by environmental conditions such as cold, heat, moisture, road dust, salt or mud.
Page 220 Driving Brake Assist (if equipped) The Brake Assist system provides full braking force during panic braking situations. It detects a rapid application of the brake pedal and maximizes the amount of brake booster assist, helping the driver to achieve maximum braking pressure. Once a panic brake application is detected, the system will remain activated as long as the brake pedal is depressed.
Page 221 Always set the parking brake fully and make sure that the gearshift is securely latched in P (Park). The parking brake is not recommended to stop a moving vehicle. However, if the normal brakes fail, the parking brake can be used to stop your vehicle in an emergency.
Page 222 Driving A limited AdvanceTrac function using only engine power reduction will still help control the wheels from over-spinning. When the brakes have cooled down, the system will again function normally. Anti-lock braking is not affected by this condition and will function normally during the cool-down period.
Page 223 when the system is active and an indicator light in the control button that will illuminate when the system is turned off. In vehicles with a message center, the message “ADVANCETRAC OFF” will be displayed. If a failure is detected in the AdvanceTrac indicator light in the instrument cluster will stay on.
Page 224 Driving STEERING Your vehicle is equipped with power steering. Power steering uses energy from the engine to decrease the driver’s effort in steering the vehicle. To prevent damage to the power steering pump: • Never hold the steering wheel to the extreme right or the extreme left for more than a few seconds when the engine is running.
Page 225: Transmission Operation
Loaded vehicles, with a higher center of gravity, may handle differently than unloaded vehicles. Extra precautions, such as slower speeds and increased stopping distance, should be taken when driving a heavily loaded vehicle. Your vehicle has the capability to haul more cargo and people than most passenger cars.
Page 226 Driving 3. Using the screwdriver (or equivalent), push the white plastic override mechanism (located behind the bracket) toward the roof of the vehicle as shown in the illustration. 4. Move the gearshift lever back to N (Neutral) (two places from P [Park]).
Page 227 Driving with a 5–speed automatic transmission Your transmission is equipped with an adaptive learning strategy found in the vehicle computer. This feature is designed to increase durability, and provide consistent shift feel over the life of the vehicle. A new vehicle or transmission may have firm and/or soft shifts.
Page 228 Driving R (Reverse) With the gearshift lever in R (Reverse), the vehicle will move backward. Always come to a complete stop before shifting into and out of R (Reverse). N (Neutral) With the gearshift lever in N (Neutral), the vehicle can be started and is free to roll.
Page 229 D (Overdrive) can be deactivated by pressing the transmission control switch on the side of the gearshift lever. This will illuminate the O/D OFF lamp and activate Drive. Drive (not shown) Drive is activated when the transmission control switch is pressed. •...
Page 230 Driving 2 (Second) Use 2 (Second) to start-up on slippery roads or to provide additional engine braking on downgrades. 1 (First) • Provides maximum engine braking. • Allows upshifts by moving gearshift lever. • Will not downshift into 1 (First) at high speeds;...
Page 231 To help avoid personal injury, always use caution when in reverse and when using the system. This system is not designed to prevent contact with small or moving objects. The system is designed to provide a warning to assist the driver in detecting large stationary objects to avoid damaging the vehicle.
Page 232 Driving dirt (do not clean the sensors with sharp objects). If the sensors are covered, it will affect the accuracy of the system. If your vehicle sustains damage to the rear bumper/fascia, leaving it misaligned or bent, the sensing zone may be altered causing inaccurate measurement of obstacles or false alarms.
Page 233 SETUP, AWD <LOCKED> will be displayed. AWD <LOCKED> provides power to all four wheels constantly which allows you to operate your vehicle in severe winter or off-road conditions such as deep snow, ice or shallow sand. It is not recommended that you use AWD <LOCKED> on dry pavement.
Page 234 Driving • To disable AWD, press RESET. The system will go back to AWD AUTO mode momentarily, then the AWD LOCKED indicator light will flash in the instrument cluster eight times every two minutes. The display will then show AWD <DISABLED> LOCKED for four seconds and then turn off.
Page 235 Basic operating principles • Drive slower in strong crosswinds which can affect the normal steering characteristics of your vehicle. • Be extremely careful when driving on pavement made slippery by loose sand, water, gravel, snow or ice. If your vehicle goes off the edge of the pavement •...
Page 236 Driving Always set the parking brake fully and make sure the gearshift is latched in P (Park). Turn the ignition to the LOCK position and remove the key whenever you leave your vehicle. If the parking brake is fully released, but the brake warning lamp remains illuminated, the brakes may not be working properly.
Page 237 Driving AWD Systems (if equipped) AWD uses all four wheels to power the vehicle. This increases traction, enabling you to drive over terrain and road conditions that a conventional two-wheel drive vehicle cannot. Sand When driving over sand, try to keep all four wheels on the most solid area of the trail.
Page 238 Driving If the transmission, transfer case or front axle are submerged in water, their fluids should be checked and changed, if necessary. Driving through deep water may damage the transmission. If the front or rear axle is submerged in water, the axle lubricant should be replaced.
Page 239 Driving Descend a hill in the same gear you would use to climb up the hill to avoid excessive brake application and brake overheating. Do not descend in neutral; instead, disengage overdrive or manually shift to a lower gear. When descending a steep hill, avoid sudden hard braking as you could lose control.
Page 240 If you have questions regarding tire replacement, see an authorized Ford or Lincoln Mercury dealer. If you nevertheless decide to equip your AWD for off-road use with tires larger than what Ford Motor Company recommends, you should not use these tires for highway driving.
Page 241 Driving Each day before you drive, check your tires. If one looks lower than the others, use a tire gauge to check pressure of all tires, and adjust if required. Check tire pressure with a tire gauge every few weeks (including spare).
Page 242: Vehicle Loading
Driving If driving through deep or standing water is unavoidable, proceed very slowly. Never drive through water that is higher than the bottom of the hubs (for trucks) or the bottom of the wheel rims (for cars). Once through the water, always try the brakes. Wet brakes do not stop the vehicle as effectively as dry brakes.
Page 243 • Maximum Trailer Weight: Maximum weight of a trailer the loaded vehicle (including occupants and cargo) is permitted to tow. It is determined by subtracting the weight of the loaded trailer towing vehicle from the GCWR for the towing vehicle. •...
Page 244: Trailer Towing
Driving Loaded vehicles, with a higher center of gravity, may handle differently than unloaded vehicles. Extra precautions, such as slower speeds and increased stopping distance, should be taken when driving a heavily loaded vehicle. Your vehicle has the capability to haul more cargo and people than most passenger cars.
Page 245 • Service your vehicle more frequently if you tow a trailer. Refer to the severe duty schedule in the scheduled maintenance guide. • Do not tow a trailer until your vehicle has been driven at least 800 km (500 miles). •...
Page 246 Driving AWD w/automatic transmission GCWR (Gross Combined Weight Rating)/Trailer Weight Engine Rear axle ratio Maximum 4.6L 3.73 Maximum frontal area of trailer is 3.72 square meters (40 square feet). Notes: For high altitude operation, reduce GCW by 2% per 300 meters (1000 ft) elevation.
Page 247 Driving Trailer hitch cover Your vehicle is equipped with a removable trailer hitch trim cover. To remove the trim cover: 1. Loosen the two push pins in the bottom of the cover by turning them counterclockwise with a flathead screwdriver or similar object. 2.
Page 248 Driving Trailer brakes Electric brakes and manual, automatic or surge-type trailer brakes are safe if installed properly and adjusted to the manufacturer’s specifications. The trailer brakes must meet local and Federal regulations. Do not connect a trailer’s hydraulic brake system directly to your vehicle’s brake system.
Page 249 Servicing after towing If you tow a trailer for long distances, your vehicle will require more frequent service intervals. Refer to your scheduled maintenance guide for more information. Trailer towing tips • Practice turning, stopping and backing up before starting on a trip to get the feel of the vehicle trailer combination.
Page 250 Driving RECREATIONAL TOWING (ALL WHEELS ON THE GROUND) Follow these guidelines for your specific powertrain combination to tow your vehicle with all four wheels on the ground (such as behind a recreational vehicle). These guidelines are designed to ensure that your transmission is not damaged due to insufficient lubrication.
Page 251: Roadside Emergencies
In the United States, this card is found in the Owner Guide portfolio in the glove compartment in Ford vehicles and is mailed to you if you own a Mercury or Lincoln. In Canada, the card is found in the Owner Information Guide in the glove compartment.
Page 252: Fuel Pump Shut-Off Switch
If you need to arrange roadside assistance for yourself, Ford Motor Company will reimburse a reasonable amount. To obtain reimbursement information, U.S. Ford or Mercury vehicles customers call 1-800-241-3673; Lincoln vehicle customers call 1–800–521–4140. Canadian customers who need to obtain reimbursement information, call 1–800–665–2006.
Page 253: Fuses And Relays
Roadside Emergencies The fuel pump shut-off switch is located in the passenger’s foot well, by the kick panel. Use the following procedure to reset the fuel pump shut-off switch. 1. Turn the ignition to the OFF position. 2. Check the fuel system for leaks. 3.
Page 254 Roadside Emergencies Note: Always replace a fuse with one that has the specified amperage rating. Using a fuse with a higher amperage rating can cause severe wire damage and could start a fire. Standard fuse amperage rating and color Fuse Mini Standard rating...
Page 255: Fuse Panel Description
The fuses are coded as follows: Fuse/Relay Fuse Amp Location Rating 2003 Aviator f/k/a Navigator LS (231) Owners Guide (post-2002-fmt) USA English (fus) Roadside Emergencies Passenger Compartment Fuse Panel Description Moonroof, Driver seat switch VAPS module, Memory seat module, Body security module, TPMS Radio, Navigation Front wiper module Flasher relay (turn/hazards)
Page 256 Roadside Emergencies Fuse/Relay Fuse Amp Location Rating 2003 Aviator f/k/a Navigator LS (231) Owners Guide (post-2002-fmt) USA English (fus) Passenger Compartment Fuse Panel Description Heated backlight relay coil, Climate seat modules, Auxiliary A/C temperature blend/mode actuator, A/C clutch relay contact Not used (spare) Restraints module Brake shift interlock...
Page 257 The relays are located on the reverse side of the passenger compartment fuse panel. To access the relays, you must remove the fuse panel. Fuse/Relay Location Relay 1 Flasher relay Relay 2 Heated backlight relay Relay 3 Delayed accessory relay Relay 4 Open Relay 5...
Page 258 Roadside Emergencies Always replace the cover to the power distribution box before reconnecting the battery or refilling fluid reservoirs If the battery has been disconnected and reconnected, refer to the Battery section of the Maintenance and specifications chapter. The high-current fuses are coded as follows: Fuse/Relay Fuse Amp Location...
Page 259 Fuse/Relay Fuse Amp Location Rating 10A* 20A* 20A* 20A* 30A** 30A** 30A** 20A** 30A** 20A* 20A* 20A* 20A* 20A* 60A** 30A** 30A** 30A** 30A** 20A** 20A** 40A** 15A* 15A* 15A* 2003 Aviator f/k/a Navigator LS (231) Owners Guide (post-2002-fmt) USA English (fus) Roadside Emergencies Power Distribution Box Description...
Page 260 Roadside Emergencies Fuse/Relay Fuse Amp Location Rating 15A* 25A* 10A* 10A* 15A* 20A* — — — — — — — — — — — — — — — 30A*** * Mini Fuses ** Maxi Cartridge Fuses *** Circuit breaker 2003 Aviator f/k/a Navigator LS (231) Owners Guide (post-2002-fmt) USA English (fus) Power Distribution Box...
Page 261 Auxiliary relay box The relay box is located on the front right fender well underneath the speed control module. The relays are coded as follows: Fuse/Relay Location Relay 64 Right HID relay Relay 65 Left HID relay Relay 66 EDF relay Rear relay box The relay box is located on the rear passenger side quarter trim panel.
Page 262 Roadside Emergencies The relays are coded as follows: Fuse/Relay Location Relay 1 Liftgate release solenoid Relay 2 Open Relay 3 Open Relay 4 Trailer tow back-up lamps Relay 5 Open Relay 6 Open Relay 7 Trailer tow battery charge Relay 8 Trailer tow park lamps Relay 9 Open...
Page 263 The use of tire sealants is not recommended and may compromise the integrity of your tires. The use of tire sealants may also affect your tire pressure monitoring system (if equipped). If your vehicle is equipped with a tire pressure monitoring system, refer to Tire Pressure Monitoring System (if equipped) in the Maintenance and specifications section for important information.
Page 264 Roadside Emergencies Note: Passengers should not remain in the vehicle when the vehicle is being jacked. 4. Block the wheel that is diagonally opposite of the flat tire using the wheel chock provided with your vehicle. Location of the spare tire and tools The spare tire and tools for your vehicle are stowed in the following locations: Tool...
Page 265 Roadside Emergencies 3. Remove the tools from the provided bag. Rotate the wrench socket out from the handle. Removing the spare tire Do not use an impact wrench on the winch drive nut. This will damage the spare tire winch. 1.
Page 266 Roadside Emergencies 2. Insert the lug wrench on the winch drive nut. The wrench will stop moving and forward resistance to turning will be felt when properly engaged. 3. Turn the wrench counterclockwise until the tire is lowered to the ground and the cable has slack.
Page 267 Roadside Emergencies 1. Use the tip of the lug wrench to remove the beauty cap by twisting the tip under the cap. The carpeted floor lid can be used as a kneeling pad. 2. Loosen each wheel lug nut by half a turn, but do not remove them until the wheel is raised off the ground.
Page 268 Roadside Emergencies 4. Position the jack according to the illustrated guides and turn the jack handle clockwise until the tire is a maximum of 25 mm (1 inch) off the ground. To lessen the risk of personal injury, do not put any part of your body under the vehicle while changing a tire.
Page 269 Roadside Emergencies 8. Remove the jack and fully tighten the lug nuts in the order shown. Stowing the flat/spare tire 1. Lay the tire on the ground with the valve stem facing up, toward the vehicle. 2. Slide the wheel partially under the vehicle and install the retainer through the wheel center.
Page 270: Jump Starting
Roadside Emergencies JUMP STARTING YOUR VEHICLE The gases around the battery can explode if exposed to flames, sparks, or lit cigarettes. An explosion could result in injury or vehicle damage. Batteries contain sulfuric acid which can burn skin, eyes and clothing, if contacted.
Page 271 Roadside Emergencies Connecting the jumper cables 1. Connect the positive (+) jumper cable to the positive (+) terminal of the discharged battery. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. 2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery.
Page 272 Roadside Emergencies 3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery. 4. Make the final connection of the negative (-) cable to the exposed ground metal surface accessible on the side of the power steering pump reservoir bracket, facing the battery.
Page 273 Roadside Emergencies Removing the jumper cables Remove the jumper cables in the reverse order that they were connected. 1. Remove the jumper cable from the ground metal surface. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. 2.
Page 274 Roadside Emergencies 3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’s battery. After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle conditions.
Page 275: Wrecker Towing
Roadside Emergencies WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or, if you are a member of a roadside assistance program, your roadside assistance service provider. It is recommended that your vehicle be towed with a wheel lift or flatbed equipment.
Page 276: Customer Assistance
Customer Assistance GETTING THE SERVICES YOU NEED At home Ford Motor Company and Ford of Canada have authorized dealerships to service your vehicle. It is preferred that you return to the authorized dealer where your vehicle was purchased when warranty repairs are needed.
Page 277 Oakville, Ontario L6J 5E4 1-800-565-3673 (FORD) www.ford.ca If you own a Lincoln vehicle and are away from home when your vehicle needs service, or if you need more help than the dealership could provide, after following the steps described above, contact the Ford Customer Relationship Center to find an authorized dealership to help you.
Page 278 • Protection against covered repair costs after your Bumper-to-Bumper Warranty expires. You may purchase Ford ESP from any participating Ford and Lincoln Mercury and Ford of Canada dealer. There are several plans available in various time, distance and deductible combinations which can be tailored to fit your own driving needs.
Page 279 What kinds of cases does the Board review? Unresolved warranty repair concerns or vehicle performance concerns as on Ford and Lincoln Mercury cars and Ford and Lincoln Mercury light trucks which are within the terms of any applicable written new vehicle warranty are eligible for review, except those involving: •...
Page 280 • A Ford or Lincoln Mercury dealership representative Consumer candidates for Board membership are recruited and trained by an independent consulting firm. The dealership Board member is chosen from Ford and Lincoln Mercury dealership management, recognized for their business leadership qualities. What the Board needs...
Page 281 Customer Assistance Oral presentations If you would like to make an oral presentation, indicate YES to question 6 on the application. While it is your right to make an oral presentation before the Board, this is not a requirement and the Board will decide the case whether or not an oral presentation is made.
Page 282 Customer Assistance UTILIZING THE MEDIATION/ARBITRATION PROGRAM (CANADA ONLY) In those cases where you continue to feel that the efforts by Ford and the dealer to resolve a factory-related vehicle service concern have been unsatisfactory, Ford of Canada participates in an impartial third party mediation/arbitration program administered by the Canadian Motor Vehicle Arbitration Plan (CAMVAP).
Page 283 Customer Assistance If your vehicle must be serviced while you are traveling or living in Central or South America, the Caribbean, or the Middle East, contact the nearest Ford dealership. If the dealership cannot help you, write or call: FORD MOTOR COMPANY WORLDWIDE DIRECT MARKET OPERATIONS 1555 Fairlane Drive Fairlane Business Park #3...
Page 284 Customer Assistance IN CALIFORNIA (U.S. ONLY) California Civil Code Section 1793.2(d) requires that, if a manufacturer or its representative is unable to repair a motor vehicle to conform to the vehicle’s applicable express warranty after a reasonable number of attempts, the manufacturer shall be required to either replace the vehicle with one substantially identical or repurchase the vehicle and reimburse the buyer in an amount equal to the actual price paid or payable by the consumer (less a reasonable allowance for consumer...
Page 285: Reporting Safety Defects (U.s. Only)
Customer Assistance REPORTING SAFETY DEFECTS (U.S. ONLY) If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Ford Motor Company. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.
Page 286: Cleaning
Cleaning WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutral Ph shampoo, such as Motorcraft Detail Wash (ZC-3–A), which is available from your dealer. • Never use strong household detergents or soap, such as dish washing or laundry liquid.
Page 287 PAINT CHIPS Your dealer has touch-up paint and sprays to match your vehicle’s color. Take your color code (printed on a sticker in the driver’s door jam) to your dealer to ensure you get the correct color. • Remove particles such as bird droppings, tree sap, insect deposits, tar spots, road salt and industrial fallout before repairing paint chips.
Page 288 Cleaning • Cover the highlighted areas to prevent water damage when cleaning the engine. • Never wash or rinse the engine while it is running; water in the running engine may cause internal damage. PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts. These products are available from your dealer.
Page 289 • Wiper blades can be cleaned with isopropyl (rubbing) alcohol or windshield washer solution. Be sure to replace wiper blades when they appear worn or do not function properly. INSTRUMENT PANEL AND CLUSTER LENS Clean the instrument panel with a damp cloth, then dry with a dry cloth. •...
Page 290 FORD, LINCOLN AND MERCURY CAR CARE PRODUCTS Your Ford, Lincoln or Mercury dealer has many quality products available to clean your vehicle and protect its finishes. These quality products have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and appearance of your vehicle.
Page 291 Cleaning Motorcraft Vinyl Conditioner (Canada only) (CXC-94) Motorcraft Deluxe Leather and Vinyl Cleaner (not available in Canada) (ZC-11–A) Ford Extra Strength Tar and Road Oil Remover* (not available in Canada) (B7A-19520–AA) Ford Extra Strength Upholstery Cleaner (not available in Canada) (E8AZ-19523–AA) Motorcraft Custom Bright Metal Cleaner (ZC-15) Motorcraft Wheel and Tire Cleaner (ZC-37–A)
Page 292: Maintenance And Specifications
Maintenance and Specifications SERVICE RECOMMENDATIONS To help you service your vehicle: • We highlight do-it-yourself items in the engine compartment for easy location. • We provide a scheduled maintenance guide which makes tracking routine service easy. If your vehicle requires professional service, your dealership can provide the necessary parts and service.
Page 293: Hood
Maintenance and Specifications OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle. 2. Go to the front of the vehicle and release the latch located in the grille. 3. Lift the hood. 2003 Aviator f/k/a Navigator LS (231) Owners Guide (post-2002-fmt) USA English (fus)
Page 294: Engine Compartment
Maintenance and Specifications IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 4.6L V8 engines 1. Engine oil dipstick 2. Brake fluid reservoir 3. Power distribution box 4. Battery 5. Power steering fluid reservoir 6. Engine oil filler cap 7. Engine coolant reservoir 8.
Page 295: Engine Oil
Maintenance and Specifications WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if the level is low. In very cold weather, do not fill the reservoir completely. Only use a washer fluid that meets Ford specification WSB-M8B16–A2. Refer to Lubricant specifications in this chapter.
Page 296 Maintenance and Specifications 4. Open the hood. Protect yourself from engine heat. 5. Locate and carefully remove the engine oil level indicator (dipstick). 6. Wipe the indicator clean. Insert the indicator fully, then remove it again. • If the oil level is between the MIN and MAX marks, the oil level is acceptable.
Page 297 Maintenance and Specifications • If the oil level is below the MIN mark, add enough oil to raise the level within the MIN-MAX range. • Oil levels above the MAX mark may cause engine damage. Some oil must be removed from the engine by a service technician. 7.
Page 298 Maintenance and Specifications Engine oil and filter recommendations Look for this certification trademark. Use SAE 5W-20 engine oil. Only use oils “Certified For Gasoline Engines” by the American Petroleum Institute (API). To protect your engine’s warranty use Motorcraft SAE 5W-20 or an equivalent 5W-20 oil meeting Ford specification WSS-M2C153–H.
Page 299: Battery
Maintenance and Specifications BATTERY Your vehicle is equipped with a Motorcraft maintenance-free battery which normally does not require additional water during its life of service. However, for severe usage or in high temperature climates, check the battery electrolyte level. Refer to the scheduled maintenance guide for the service interval schedules.
Page 300 Maintenance and Specifications When lifting a plastic-cased battery, excessive pressure on the end walls could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the vehicle or battery. Lift the battery with a battery carrier or with your hands on opposite corners.
Page 301 Maintenance and Specifications If the battery has been disconnected or a new battery has been installed, the clock and the preset radio stations must be reset once the battery is reconnected. • Always dispose of automotive batteries in a responsible manner. Follow your local authorized standards for disposal.
Page 302 Maintenance and Specifications When the engine is cold, check the level of the engine coolant in the reservoir. • The engine coolant should be at the “cold fill level” or within the “cold fill range” as listed on the engine coolant reservoir (depending upon application).
Page 303 Only a qualified technician should add engine coolant to your vehicle. If the coolant level is LOW or if there are any coolant system problems, contact you local Lincoln dealer. Do not put engine coolant in the windshield washer fluid container.
Page 304 Maintenance and Specifications Severe climates If you drive in extremely cold (less than –36° C [–34° F]) or extremely hot climates, it may be necessary to adjust the coolant concentration levels. • Extreme cold: increase the coolant concentration above 50%. NEVER increase the coolant concentration above 60%.
Page 305 Maintenance and Specifications Continued operation will increase the engine temperature: • The engine will completely shut down. • Steering and braking effort will increase. Once the engine temperature cools, the engine can be re-started. Take your vehicle to a service facility as soon as possible to minimize engine damage.
Page 306 Maintenance and Specifications If you do not use the proper fuel filler cap, excessive pressure or vacuum in the fuel tank may damage the fuel system or cause the fuel cap to disengage in a collision, which may result in possible personal injury.
Page 307 Maintenance and Specifications splashed on the skin, promptly wash skin thoroughly with soap and water. Consult a physician immediately if you experience an adverse reaction. When refueling always shut the engine off and never allow sparks or open flames near the filler neck. Never smoke while refueling.
Page 308 Maintenance and Specifications after some fuel is used (fuel gauge drops below full). Once the fuel filler cap is properly secured, “CHECK/TIGHTEN FUEL CAP” will turn off after a short period of driving. If you must replace the fuel filler cap, replace it with a fuel filler cap that is designed for your vehicle.
Page 309 Maintenance and Specifications with the recommended octane rating, see your dealer or a qualified service technician to prevent any engine damage. Fuel quality If you are experiencing starting, rough idle or hesitation driveability problems during a cold start, try a different brand of gasoline. If the problems persist, see your dealer or a qualified service technician.
Page 310 Maintenance and Specifications ESSENTIALS OF GOOD FUEL ECONOMY Measuring techniques Your best source of information about actual fuel economy is you, the driver. You must gather information as accurately and consistently as possible. Fuel expense, frequency of fill-ups or fuel gauge readings are NOT accurate as a measure of fuel economy.
Page 311 Maintenance and Specifications Calculating fuel economy 1. Fill the fuel tank completely and record the initial odometer reading (in kilometers or miles). 2. Each time you fill the tank, record the amount of fuel added (in liters or gallons). 3. After at least three to five tank fill-ups, fill the fuel tank and record the current odometer reading.
Page 312 Maintenance and Specifications • You may want to turn off the speed control in hilly terrain if unnecessary shifting between gears occurs. Unnecessary shifting of this type could result in reduced fuel economy. • Warming up a vehicle on cold mornings is not required and may reduce fuel economy.
Page 313 Maintenance and Specifications EPA window sticker Every new vehicle should have the EPA window sticker. Contact your dealer if the window sticker is not supplied with your vehicle. The EPA window sticker should be your guide for the fuel economy comparisons with other vehicles.
Page 314 Maintenance and Specifications Exhaust leaks may result in entry of harmful and potentially lethal fumes into the passenger compartment. Do not make any unauthorized changes to your vehicle or engine. By law, vehicle owners and anyone who manufactures, repairs, services, sells, leases, trades vehicles, or supervises a fleet of vehicles are not permitted to intentionally remove an emission control device or prevent it from working.
Page 315 Maintenance and Specifications 1. Start the engine and let it run until it reaches normal operating temperature (the engine coolant temperature gauge indicator will be near the center of the normal area between H and C). 2. While the engine idles, turn the steering wheel left and right several times.
Page 316 Maintenance and Specifications TRANSMISSION FLUID Checking automatic transmission fluid The automatic transmission does not have a transmission fluid dipstick. Refer to your scheduled maintenance guide for scheduled intervals for fluid checks and changes. Your transmission does not consume fluid. However, the fluid level should be checked if the transmission is not working properly, (i.e., if the transmission slips or shifts slowly) or if you notice some sign of fluid leakage.
Page 317 Maintenance and Specifications government test course. For example, a tire graded 150 would wear one and one-half (1 1/2) times as well on the government course as a tire graded 100. The relative performance of tires depends upon the actual conditions of their use, however, and may depart significantly from the norm due to variations in driving habits, service practices, and differences in road characteristics and climate.
Page 318 Maintenance and Specifications • Adjust tire pressure to recommended specifications found on the Certification Label. Tire pressure information can also be found on the Tire Information label located on the inside of the fuel filler door. • Check tires for proper air pressure monthly. Check spare tire for proper air pressure every six months.
Page 319 Maintenance and Specifications Replacing the tires Replace the tires when the wear band is visible through the tire treads. Due to exposure to the elements and exhaust you should replace the spare tire when you replace the other tires. When replacing full size tires, never mix radial bias-belted, or bias-type tires.
Page 320: Part Numbers
Maintenance and Specifications Follow these guidelines when using snow tires and chains: • Use only cable type chains or chains offered by Ford as an accessory or equivalent. Other conventional link type chains may contact and cause damage to the vehicle’s wheel house and/or body. •...
Page 321: Refill Capacities
Maintenance and Specifications REFILL CAPACITIES Fluid Ford Part Name Brake fluid Motorcraft High Performance DOT 3 Motor Vehicle Brake Fluid Engine oil Motorcraft SAE (including filter 5W-20 Premium change) Synthetic Blend Motor Oil (US) Motorcraft SAE 5W-20 Super Premium Motor Oil (Canada) Fuel tank Power steering...
Page 322 Maintenance and Specifications Fluid Ford Part Name Front axle Motorcraft SAE lubricant 80W-90 Premium Rear Axle Lubricant Rear axle Motorcraft SAE lubricant 75W-140 High Performance Synthetic Rear Axle Lubricant Windshield Motorcraft washer fluid Ultra-Clear Windshield Washer Concentrate Ensure the correct automatic transmission fluid is used. MERCON and MERCON V are not interchangeable.
Page 323: Lubricant Specifications
Maintenance and Specifications LUBRICANT SPECIFICATIONS Ford Part Item Name or equivalent Body hinges, latches, door striker plates and rotors, seat Multi-Purpose tracks, fuel filler Grease or door hinge and Multi-Purpose spring, hood Grease Spray latch, auxiliary latch, seat tracks Motorcraft High Performance Brake fluid DOT 3 Motor...
Page 324 Maintenance and Specifications Ford Part Item Name or equivalent Motorcraft Automatic MERCON V transmission Motorcraft Power steering MERCON fluid Multi-Purpose 75W-140 High performance Rear axles synthetic rear axle lubricant Motorcraft SAE Front axle 80W-90 (AWD) Premium Rear Axle Lubricant Motorcraft Transfer case MERCON (AWD)
Page 325: Table Of Contents
Maintenance and Specifications ENGINE DATA VEHICLE DIMENSIONS Vehicle dimensions (1) Overall length (2) Vehicle width (body) (3) Vehicle width (including mirrors) (4) Maximum height* (5) Wheelbase (6) Track width, front (6) Track width, rear * P245 tire with roof rack 2003 Aviator f/k/a Navigator LS (231) Owners Guide (post-2002-fmt) USA English (fus)
Page 326 Maintenance and Specifications IDENTIFYING YOUR VEHICLE Certification label The National Highway Traffic Safety Administration Regulations require that a Certification label be affixed to a vehicle and prescribe where the Certification label may be located. The Certification label is located on the front door latch pillar on the driver’s side.
Page 327 Maintenance and Specifications Vehicle identification number (VIN) The vehicle identification number is attached to a metal tag and is located on the driver side XXXXXXXXXXXXXXXXX instrument panel. (Please note that in the graphic XXXX is representative of your vehicle identification number.) Engine number The engine number (the last eight numbers of the vehicle identification number) is stamped on the engine block and transmission.
Page 328: Accessories
FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of genuine Ford accessories are available for your vehicle through your local authorized Ford, Lincoln, Mercury or Ford of Canada dealer. These quality accessories have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and aerodynamic appearance of your vehicle.
Page 329 Accessories Home link Keyless entry Navigation system Rear park assist Remote start system Seat back organizer Tire step Video entertainment system (DVD) Travel equipment Ash cup Automatic headlamp system with DRL Canoe carrier Daytime running lights (DRL) First aid kit Highway safety kit Interior mirror, electrochromatic with compass (with and without temperature display)
Page 330 Accessories Cargo liners, interior Carpet floor mats Door edge guards Flat splash guards Fog lamps Front end covers (full and sport) Front hood deflectors Locking gas cap Molded splash guards Secure start — emergency battery start Side window air deflectors Universal floor mats For maximum vehicle performance, keep the following information in mind when adding accessories or equipment to your vehicle:...
Page 331: Index
Index ABS (see Brakes) ...219 Accessory delay ...124 Air bag supplemental restraint system ...196, 200 and child safety seats ...198 description ...196, 200 disposal ...203 driver air bag ...198, 201 indicator light ...12, 202 operation ...198, 201 passenger air bag ...198, 201 side air bag ...200 Air cleaner filter ...320 Air conditioning ...92...
Page 332 Index Child safety seats ...206 attaching with tether straps ..210 in front seat ...208 in rear seat ...208 Cleaning your vehicle engine compartment ...287 instrument panel ...289 interior ...289–290 interior trim ...290 plastic parts ...288 washing ...286 waxing ...286 wheels ...287 wiper blades ...288 Clock ...27, 38, 120 Compass, electronic...
Page 333 fail-safe coolant ...304 idle speed control ...299 lubrication specifications ...323, 325 refill capacities ...321 service points ...294 starting after a collision ...252 Engine block heater ...218 Engine oil ...295 change oil soon warning, message center ...295 checking and adding ...295 dipstick ...295 filter, specifications ...298, 320 recommendations ...298...
Page 334 Index Head restraints ...174 Headlamps ...101 aiming ...104 autolamp system ...101 bulb specifications ...107 daytime running lights ...103 flash to pass ...104 high beam ...13, 103 replacing bulbs ...109 turning on and off ...101 warning chime ...14 Heating heating and air conditioning system ...92 HomeLink universal transceiver (see Garage...
Page 335 turn signal indicator ...13 Load limits ...242 GAWR ...242 GVWR ...242 trailer towing ...242 Loading instructions ...243 Locks childproof ...157 doors ...157 Lubricant specifications ...323, 325 Lumbar support, seats ...175 Manual transmission fluid capacities ...321 lubricant specifications ...325 Message center ...139–140 english/metric button ...144 system check button ...143 warning messages ...146...
Page 336 Index Remote entry system ...157, 159 illuminated entry ...163 locking/unlocking doors ...157–158, 162 opening the trunk ...159 panic alarm ...159 replacement/additional transmitters ...161 replacing the batteries ...160 Roadside assistance ...251 Roof rack ...155 Safety Belt Maintenance ...195 Safety belts (see Safety restraints) ...14, 186–189, 191 Safety Canopy ...201 Safety defects, reporting ...285...
Page 337 Trip odometer ...16 Trunk ...159 Turn signal ...13, 106 Vehicle dimensions ...325 Vehicle Identification Number (VIN) ...327 Vehicle loading ...242 Ventilating your vehicle ...218 Warning chimes ...14 Index Warning lights (see Lights) ...10 Washer fluid ...295 Water, Driving through ...241 Windows power ...121 rear wiper/washer ...116...

This manual is also suitable for:

2003 navigator ls

Lincoln Aviator 2003 Owner's Manual

Introduction

Instrument Cluster

Entertainment Systems

Climate Controls

Lights

Driver Controls

Quick Links

Table of Contents

Related Manuals for Lincoln Aviator 2003

Summary of Contents for Lincoln Aviator 2003

This manual is also suitable for:

Table of Contents