................30 J111A, COSHM111A, COLFM111A 4 Dimensional Drawings ........................32 BDCOELV00AAE ........................33 Figures ® Figure 1 The Bolts in Milnor Equipment................10 Figure 2 Apply Threadlocker in a Blind Hole.................15 Figure 3 Apply Threadlocker in a Through Hole..............16 Figure 4 Use heat for disassembly of fasteners with threadlocker..........16...
Page 4
Parts List— ....................24 COELV00A Table 19 Parts List—Lift Frame Balancing Assembly ..........26 COELV00A Table 20 Parts List—Air Cylinder Lubricator & Shuttle Valve ......28 COELV00A Table 21 Parts List—Horizontal Beds 42x62 and 44x65 COELV00A111/112, COSHM1LP, ................31 COLFJ111A, COSHM111A, COLFM111A Pellerin Milnor Corporation...
Email: parts@milnor.com BNUUUU02 / 2021104A BNUUUU02 0000158094 3/3/21 9:47 AM Released Trademarks BNUUUU02.R01 0000158093 A.2 F.2 E.2 3/3/21 9:47 AM Released These words are trademarks of Pellerin Milnor ® Corporation and other entities: Table 1. Trademarks AutoSpot™ GreenFlex™ MilMetrix ®...
Keep yourself and others clear of movement areas and paths. � Understand the consequences of placing a system machine on line. � Know the location of all emergency stop switches, pull cords, and/or kick plates and � use them in an emergency to stop machine motion. Pellerin Milnor Corporation...
Do not unlock or open electric box doors. � WARNING: Entangle and Crush Hazards — Guards, covers, and panels—Operating the machine with any guard, cover, or panel removed exposes moving components. Do not remove guards, covers, or panels. � Pellerin Milnor Corporation...
You have total control of machine movement immediately after setting the Manual/Automatic switch to manual. Keep yourself and others clear of movement areas and paths. � Understand the consequences of operating manually. � Pellerin Milnor Corporation...
BNUUUN02.C01 0000222451 A.2 B.3 A.3 1/2/20 2:14 PM Released The document about the assembly gives the torque requirements for other fasteners. If fastener torque specifications or threadlocker requirements in an assembly document are different from this document, use the assembly document. Pellerin Milnor Corporation...
Genereal Service Information Figure 1. The Bolts in Milnor ® Equipment Legend The Marks on Bolt Heads A... SAE Grades 1 and 2, ASTM A307, and stainless steel B... Grade BC, ASTM A354 C... SAE Grade 5, ASTM A449 D...
Do not use flammable material near ignition sources. � 1. Clean all threads with a wire brush or a different tool. 2. Remove the grease from the fasteners and the mating threads with solvent. Make the parts dry. Pellerin Milnor Corporation...
3. Tighten the bolt to the value shown in the correct table (Table 6: Threadlocker by the Diame- ter of the Bolt (see below Note ), page 12 Table 12: Torque Values for Stainless Steel Fas- teners 5/16-inch and Smaller, page 14 Pellerin Milnor Corporation...
For low-strength and moderate-strength threadlocker, disassemble with hand tools. Figure 4. Use heat for disassembly of fasteners with threadlocker. Legend Apply Heat to a Small Area A... How to apply heat to a small fastener B... How to apply heat to a large fastener Pellerin Milnor Corporation...
"all" in the "Used In" column. The numbers shown in the "Item" column are those shown in the illustrations. Description/Nomenclature Used In Item Part Number Comments Components 01 10375B NPLT:ELEC HAZARD SMALL-TCATA 01 10564A NPLT:COSHA HAZARDS-TCATA 01 10699A NPLT:SERV HZRD-PLYEST-TCATA Pellerin Milnor Corporation...
"all" in the "Used In" column. The numbers shown in the "Item" column are those shown in the illustrations. Description/Nomenclature Used In Item Part Number Comments Components 01 10375 NPLTE:"WARNING" 2X2 01 10564X WARNINGS:SHUTTLE ISO Pellerin Milnor Corporation...
Find the assembly for your machine and the letter shown in the "Item" column. The components for your machine will show this letter or the word "all" in the "Used In" column. The numbers shown in the "Item" column are those shown in the illustrations. Description/Nomenclature Used In Item Part Number Comments Components 04 21496 SAFETY PIN-COSHA Pellerin Milnor Corporation...
Mechanical Components BPVIEF01 / 2021422A BPVIEF01.1 0000398753 10/14/21 8:01 AM Released Stand & Air Cylinder 2 Sheet COELV00A Legend D1.. Detail Rod Eye and Clevis D2.. Detail Muffler D3.. Detail Rod End and Clevis D4.. Detail Check Valve Pellerin Milnor Corporation...
1 Sheet COELV00A Legend A... Components shown above and listed on the parts list are correct for the COELV00A, but the pictures are not of the lubricator installed to the COELV00A. Table 20. Parts List—Air Cylinder Lubricator & Shuttle Valve Find the assembly for your machine and the letter shown in the "Item"...
Released Horizontal Bed 42Wx62L, 44Wx65L 2 Sheet COELV00A111/112, COSHM1LP, COLFJ111A, COSHM111A, COLFM111A Legend N1.. To order gear reducers, supply the parts department with your gear reducer’s serial number and gear ratio. An ex- ample is shown here. Pellerin Milnor Corporation...