Copy Of Safety Decal - Regency Grandview G600C Owners & Installation Manual

Table of Contents

Advertisement

safety decal
This is a copy of the label that accompanies each Grandview™ G600C Direct Vent Gas Fireplace. We have printed a copy of the contents here for your review.
NOTE: Regency
units are constantly being improved. Check the label on the unit and if there is a difference, the label on the unit is the correct one.
®

Copy of Safety Decal

Listed/Nom: Vented Gas Fireplace Heater / Foyer au Gaz à Évacuation
Certified to/Certifi pour:
é
MAY BE INSTALLED IN MANUFACTURED (MOBILE) HOMES AFTER FIRST SALE.
Refer to Intertek's Directory of Building Products for detailed information.
Pour plus de détails , se reporter au Répertoire des produits de construction de Intertek.
C #: 4001172
NATURAL GAS: Model G600C-NG
Minimum supply pressure
5.0"
Manifold pressure high
3.8"
Manifold pressure low
1.1"
Orifice size
#46
Minimum input
11,500
Maximum input
21,000
Altitude
0-4500 ft/pi
PROPANE GAS: Model G600C-LP
Minimum supply pressure
11"
Manifold pressure high
10.5"
Manifold pressure low
2.9"
#55
Orifice size
Minimum input
11,000
Maximum input
20,500
Altitude
0-4500 ft/pi
This appliance must be installed in accordance with local codes, if any; if none, follow the National Fuel Gas Code, ANSI Z223.1.
This appliance must be installed in accordance with the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280, in the United States, or when such a standard is not applicable,
ANSI/NCSBCS A225.1/NFPA 501A, Manufactured Home Installations Standard or ANSI A119.2 ou NFPA 501C Standard for Recreational Vehicles
This appliance is only for use with the type of gas indicated on the rating plate and may be installed in an aftermarket, permanently located, manufactured (mobile) home where not prohibited by local codes. See
owner's manual for details. This appliance is not convertible for use with other gases, unless a certified kit is used. (Kit #776-977). Fan Part # 761-979.
Installer l'appareil selon les codes ou règlements locaux, ou, en l'absence de tels règlements, selon les codes d'installation ANSI Z223.1. Installer l'appareil selon la norme 24 CFR, Part 3280, Manufactured Home
Construction and Safety Standard. Si ces normes ne sont pas pertinentes, utilisez la norme ANSI/NCSBCS A225.1/NFPA 501A, Manufactured Home Installations Standard, ou ANSI A119.2 ou NFPA 501C
Standard for Recreational Vehicles. Cet appareil doit être utilisé uniquement avec le type de gaz indiqué sur la plaque signalétique. Cet appareil peut être installé dans une maison préfabriquée ou mobile (É.-U.
seulement) installée à demeure si les règlements locaux le permettent. Voir la notice de l'utilisateur pour plus de renseignements. Cet appareil ne peut pas être utilisé avec d'autres gaz sauf si une trousse de
conversion certifiée est fournie.
This vented gas fireplace heater is not for use with air filters.
FOR USE WITH GLASS DOORS CERTIFIED WITH THE APPLIANCE ONLY
For Use Only with Barrier (Part # 776-109/P)
Part No. 946-556 HeatWave Kit may be used. La trousse HeatWave (pièce no. 946-556) peut être utilisée.
Electrical supply/Alimentation électrique 115VAC, 1.5A, 60Hz.
NOT FOR USE WITH SOLID FUELS /
CSA P.4.1 Fireplace Efficiency (FE) / Efficacité énergétique des foyers (EEF) CSA P.4.1
Natural Gas / Gaz naturel:
62.13%
Propane Gas / Gaz propane: 64.64%
Part #: 920-269a
Colour: Everything black on grey except what is highlighted is printed red.
Size: File@100% 9.117''W x 6.045''H
For the State of Massachusetts, installation
May 4/20: Created Draft
Mar. 17/21: Updated CSA/ANSI date
and repair must be done by a plumber or
gas fitter licensed in the Commonwealth of
Massachusetts.
*Printer:Start serial sequence @ 000001
For the State of Massachusetts, flexible con-
nectors shall not exceed 36 inches in length.
For the State of Massachusetts, the appli-
ances individual manual shut-off must be a
t-handle type valve.
The State of Massachusetts requires the
installation of a carbon monoxide alarm in
accordance with NFPA 720 and a CO alarm
with battery back up in the same room where
the gas appliance is installed.
6 | Grandview
G600C Gas Fireplace
®
ANSI Z21.88-2019
APPAREIL FONCTIONNANT AU GAZ NATUREL
Modèle G600C-NG
Pression d'alimentation minimale
WC/C.E. (1.25 kPa)
Pression manifold - haute
WC/C.E. (0.94 kPa)
Pression manifold - basse
WC/C.E. (0.27 kPa)
Taille de l'orifice
DMS
D bit calorifique minimal
é
Btu/h
3.37 kWh
D bit calorifique maximal
é
Btu/h
6.15 kWh
(0-1372 m)
Altitude
APPAREIL FONCTIONNANT AU GAZ PROPANE
Modèle
G600C
-LP
Pression d'alimentation minimale
WC/C.E. (2.74 kPa)
Pression manifold - haute
WC/C.E. ( 2.61 kPa)
WC/C.E. (0.72 kPa)
Pression manifold - basse
DMS
Taille de l'orifice
Btu/h
3.22 kWh
D bit calorifique minimal
é
B tu/h
6.01 kWh
D bit calorifique maximal
é
(0-1372 m)
Altitude
NE PAS UTILISER AVEC UN COMBUSTIBLE SOLIDE
Decal Location
DO NOT REMOVE DECAL FROM UNIT.
Duplicate S/N
DO NOT REMOVE THIS LABEL / NE PAS ENLEVER CETTE ÉTIQUETTE
Minimum Clearances to Combustibles / Rear Vent—Clean Finish
Dégagements minimaux par rapport aux matériaux combustibles
D
C
A
DOOR SEAL: Please
check that the door is
properly sealed
(See Instruction Manual for detailed instructions)
Ne pas utiliser de filtre à air avec ce foyer au gaz à évacuation.
POUR UTILISATION UNIQUEMENT AVEC LES PORTES EN VERRE CERTIFIÉES AVEC L'APPAREIL
Utiliser uniquement avec l'écran ( n ° 776-109/P)
FPI Fireplace Products International Ltd. Delta, BC, Canada
542
Serial No./ No de série
542
0" Clearance to combustibles from
Top, sides, and bottom of unit
0.5" Clearance to combustibles from
rear of unit
Mantel Clearances from
Fireplace Opening /
(A) 12" (305 mm) at max. depth
Side Wall Clearance from Fireplace
Opening /
F
B) Min 6" (152 mm)
B
Ceiling from Top of Fireplace
Opening:
C) Min. 44.25" (1124 mm)
Mantel Depth:
D) Max. 12" (305 mm)
Alcove Clearances:
E) Min. Width 84" (2134 mm)
E
F) Max. Depth 36" (914 mm)
Minimum Vent Clearances:
Horizontal Top
2" (51 mm)
Horizontal Side
1-1/2" (38 mm)
Horizontal Bottom
1-1/2" (38 mm)
Vertical Vent
1-1/2" (38 mm)
Made in Canada/ Fabriqué au Canada
920-269a
Remove bottom cover—decal
will be on the floor of the unit

Advertisement

Table of Contents
loading

Table of Contents