Model Menu(Airplane/Glider) - FUTABA T16IZ Short Manual

MODEL MENU (Airplane/Glider functions)
The dedicated mixes, etc. usable when airplane
or glider model type is selected are displayed
in this Model menu functions section. First use
the Model type function of the Linkage menu to
preset the model type, wing type, and tail type
matched to the fuselage used. Other settings reset
the data used in mixing function, etc.
These dedicated mixes can be set for each
flight condition, as required. When you want to
use the system by switching the settings for each
condition by switch or stick position, use the
Model menu (Airplane/Glider) functions table
Servo monitor
Displays the servo test and operation position
Condition select
Flight conditions addition, deletion, copy, condition renaming, and condition
delay can be set.
AFR
Sets the angle and curve of all the operation functions.
Dual rate
D/R curve which can be switched with a switch, etc. can also be added.
Program. mixes
Program mixing which can be freely customized. Up to 10 mixes can be used for
each condition.
This function adjusts the left and right ailerons. Roll axis correction and fine
Aileron differential
tuning with a VR are also possible. This is convenient when making settings
during flight.
Flap setting
The flaps can be adjusted independently. For a 4 flaps model, the camber flaps
can be mixed with the brake flaps.
AIL → Camber flap
This mix operates the camber flaps in the aileron mode. It improves the
operation characteristic of the roll axis.
AIL → Brake flap
This mix operates the brake flaps in the aileron mode. It improves the operation
characteristic of the roll axis.
Aileron → Rudder
This mix is used when you want to operate the rudder at aileron operation.
Banking at a shallow bank angle is possible.
Elevator → Camber
This mix is used when you want to the mix camber flaps with elevator operation.
Lifting force can be increased at elevators up.
Camber mixing
This mix adjusts the camber and corrects the elevators.
Airbrake → ELE
This mix is used to correct operation of the airbrakes (spoilers) when landing.
Camber flap → ELE
This mix is used to correct for attitude changes when the camber flaps are being
used.
Rudder → Aileron
This function is used to correct roll knife edge, etc. of stunt planes.
Rudder → Elevator
This function is used to correct roll maneuvers, knife edge, etc. of stunt planes.
Butterfly (Crow)
This function is used when powerful brake operation is necessary.
Trim mix 1/2
The ailerons, elevators, and flaps trim offset rate can be called by switch or
condition selection.
Snap roll
This function selects the snap roll switch and adjusts the steering angle of each
rudder. Servo speed can also be adjusted.
Air brake
This function is used when airbrakes are necessary when landing or when diving,
etc. during flight.
Gyro
This is a dedicated mix when a GYA Series gyro is used.
Ailevator
This function adjusts the elevators and ailerons of models with elevator
specifications.
Acceleration
Allows a brief "overload" in response to sudden Elevator, Elevator → Camber,
and Ail → Rudder.
Motor
The operation speed when the motor of F5B and other EP gliders is started by
switch can be set.
V-Tail
This function adjusts the elevators and rudder of V-tail models.
Winglet
This function adjusts the left and right rudders of winglet models.
Condition select function to add flight conditions.
(Up to 8 conditions can be used)
Note: The T16IZ is designed so that the airplane and
glider model types can handle aircraft of the same
wing type.
The functions common to airplanes and gliders,
except some dedicated functions, are summarized
without regard to the model type.
The setting items are different, depending on the
number of servos, etc. according to the wing type
used. The setup screens in the instruction manual
are typical examples.
[Airplane/glider, 2 ailerons or more]
[Airplane/glider, 2 flaps or more]
[Airplane/glider, 2 ailerons + 2 flaps or more]
[Airplane/glider, 4 flaps or more]
[Airplane/glider, 2 ailerons or more]
[Airplane/glider, 2 ailerons or more]
[Airplane/glider, 2 ailerons + 1 flap or more]
[Airplane/glider/multicopter, general]
[Airplane/glider, elevator specifications]
[Airplane/glider, V-tail specifications]
[Airplane/glider, winglet specifications]
[Airplane/glider, general]
[Airplane/glider, general]
[Airplane/glider, general]
[Airplane, general]
[Glider, 2 ailerons or more]
[Glider general]
[Airplane general]
[Airplane, general]
[Glider general]
[Airplane/glider, general]
37