Related Manuals for Sharp XEA147BK
Summary of Contents for Sharp XEA147BK
- Page 1 XEA147BK And XEA147WH Frequently Asked Questions. XEA147BK and XEA147WH Frequently Asked Questions Page 1 of 21...
- Page 2 AC outlet, wait at least one minute, and then try again. If there were any data from a previous programming attempt, they would have been cleared XEA147BK and XEA147WH Frequently Asked Questions Page 2 of 21...
- Page 3 If the unit is not used for some months, you might not get any warning when you turn it on that the batteries have failed. In this instance, the XEA147 will initialise itself. XEA147BK and XEA147WH Frequently Asked Questions Page 3 of 21...
- Page 4 1. Pull the printer cover forward and detach it. The paper cutter is mounted on the printer cover, be careful not to cut yourself. 2. Lift up the print roller arm. XEA147BK and XEA147WH Frequently Asked Questions Page 4 of 21...
- Page 5 Note: Before placing a new paper roll in the paper roll cradle, cut off the pasted (taped), part of the paper and confirm that the cut end of the paper is straight. XEA147BK and XEA147WH Frequently Asked Questions Page 5 of 21...
- Page 6 If the paper end does not come out. Open the printer cover, and pass the paper end between the paper cutter and the paper guide of the printer cover, and replace the cover. XEA147BK and XEA147WH Frequently Asked Questions Page 6 of 21...
- Page 7 How do I set a 10% GST rate? 1. Set the mode key to the Z/PGM position 2. Enter: #/TM/ST 9 /RCPT SW 1 /RCPT SW 1 0 0 0 0 0 #/TM/ST TL/AT/NS XEA147BK and XEA147WH Frequently Asked Questions Page 7 of 21...
- Page 8 /RCPT SW 0 SHIFT TL/AT/NS Enter 1 before you press the department key to make the department taxable Enter 0 before you press the department key to make the department non-taxable. XEA147BK and XEA147WH Frequently Asked Questions Page 8 of 21...
- Page 9 You can also enter text using 3 digit codes. Please refer to the full instruction manual (pages 43 -44) for details. The character table for using the department and function keys is shown below. XEA147BK and XEA147WH Frequently Asked Questions Page 9 of 21...
- Page 10 This will set the power save time to 100 minutes. This is the maximum time which can be set before the power save mode activates. The default time is 30 minutes. XEA147BK and XEA147WH Frequently Asked Questions Page 10 of 21...
- Page 11 You can also enter text using 3 digit codes. Please refer to the full instruction manual (pages 43 -44) for details. The character table for using the department and function keys is shown on the next page. XEA147BK and XEA147WH Frequently Asked Questions Page 11 of 21...
- Page 12 XEA147BK and XEA147WH Frequently Asked Questions Page 12 of 21...
- Page 13 30 characters #/TM/ST TL/AT/NS 7. Enter the Fifth line do the following: #/TM/ST -1- -0- -4- _/RCPT/SW_ -5- _/RCPT/SW_ use the keyboard to enter up to 30 characters #/TM/ST TL/AT/NS XEA147BK and XEA147WH Frequently Asked Questions Page 13 of 21...
- Page 14 You can also enter text using 3 digit codes. Please refer to the full instruction manual (pages 43 -44) for details. The character table for using the department and function keys is shown below. XEA147BK and XEA147WH Frequently Asked Questions Page 14 of 21...
- Page 15 When the “Flat Battery/No Battery” symbol is displayed the battery must be replace immediately. If not the XEA147 will lose all its programmed settings, and any sales data if the power fails or is turned off. XEA147BK and XEA147WH Frequently Asked Questions Page 15 of 21...
- Page 16 When they are installed correctly, the low battery or no battery message will disappear. 5. Close the battery compartment cover. 6. Replace the printer cover. XEA147BK and XEA147WH Frequently Asked Questions Page 16 of 21...
- Page 17 1. Enter the amount to remove in cents. For example $15.00 is entered as: 5 0 0 2. Press the key. 3. Press the department key you wish to remove the $15.00 from. For example department 2: XEA147BK and XEA147WH Frequently Asked Questions Page 17 of 21...
- Page 18 Transaction totals such as Cash in Drawer. The amounts removed will be added to the Void Mode Transaction totaliser. A Void Mode receipt will print even if the receipt is switched off. XEA147BK and XEA147WH Frequently Asked Questions Page 18 of 21...
- Page 19 #/TM/ST #/TM/ST 2. Turn the mode key to Z/PGM 3. Enter the following: #/TM/ST TL/AT/NS - 4. Turn the mode key back to REG. The “E34” problem should be fixed. XEA147BK and XEA147WH Frequently Asked Questions Page 19 of 21...
- Page 20 To produce a daily X report, do the following: 1. Turn the mode key to X/Flash position 2. Press the TL/AT/NS Your daily X report will print. It will have *X1* printed at the top of the report. XEA147BK and XEA147WH Frequently Asked Questions Page 20 of 21...
- Page 21 XEA147. Please refer to the XEA147 instruction manual for more guidance on functions and programming steps not covered in these “Frequently Asked Questions”. XEA147BK and XEA147WH Frequently Asked Questions Page 21 of 21...