Kenwood NX-220 Service Manual page 9

When you enter the password and press the [ ] or [ ]
key, "CLONE" is displayed if the entered password is
correct. If the password is incorrect, "CLN LOCK" is re-
displayed.
• How to enter the password using the Selector;
If the Selector is rotated while "CLN LOCK" is displayed,
the Read authorization password input screen is dis-
played.
If the Selector is rotated while the Read authorization
password input screen is displayed, the number (0 to 9)
blinks on the LCD. When you press the [ ] key, the cur-
rently selected number is determined. If you press the
[ ] key after entering the password in this procedure,
"CLONE" is displayed if the entered password is correct.
If the password is incorrect, "CLN LOCK" is redisplayed.
4. Power ON the target transceiver.
5. Connect the cloning cable (part No. E30-3410-05) to the
SP/MIC connectors on the source and target.
6. Press the [ ] key on the source while the source displays
"CLONE". The data of the source is sent to the target.
While the target is receiving the data, "PROGRAM" is
displayed. When cloning of data is completed, the source
displays "END", and the target automatically operates in
the User mode. The target can then be operated by the
same program as the source.
7. The other target can be continuously cloned. When the
[ ] key on the source is pressed while the source displays
"END", the source displays "CLONE". Carry out the op-
eration in step 4 to 6.
Note:
• Cannot be cloned if the password (overwrite password) is
programmed to the target.
• "Model Name" must be same to clone the transceiver.
8. Firmware Version Information
(C model only)
Press and hold the [ ] key while turning the transceiver
power ON and then keep pressing and holding the [ ] key,
the fi rmware version information appears on the LCD.
REALIGNMENT /
Cloning cable / 复制电缆
(E30-3410-05)
Fig. 2 / 图 2
模式组合
输 入 密 码 并 按 [ ] 或 [
确，则显示"C L O N E" 。如果密码错误，则再次显示"C L N
LOCK" 。
• 如何使用选择器输入密码 ；
如果在显示"CLN LOCK"时转动选择器，将显示读取授权
密码输入画面。
如果在显示读取授权密码输入画面时转动选择器，数字 (0
至 9) 将在 L C D 上闪烁。按 [
字。在此步骤输入密码后按 [
确，则显示"CLONE" 。
如果密码错误，则再次显示"CLN LOCK" 。
4. 打开子手持对讲机的电源。
5. 将复制电缆 ( 零件号 E30-3410-05) 连接到主对讲机和子对
讲机的 SP/MIC 连接器上。
6. 主对讲机上显示"C L O N E"时，按主对讲机上的 [
主对讲机的数据被发送到子对讲机上。
子对讲机接收数据时，显示"PROGRAM" 。数据复制完成后，
主对讲机显示"E N D" ，子对讲机自动按用户模式操作。然
后子对讲机便可按与主对讲机相同的程序操作。
7. 可以继续对另一子对讲机进行复制。如果在主对讲机显示
"END"时按主对讲机的 [
执行步骤 4 至 6 的操作。
注意 :
• 如果子对讲机设有密码 ( 改写密码 )，则无法复制。
• "型号名称"必须相同，才能复制手持对讲机。
8. 固件版本信息
( 仅限 C 型号 )
打开手持对讲机电源时按住 [ ] 键， 然后一直按住 [ ] 键，
LCD 上便出现固件版本信息。
NX-220
] 键 时， 如 果 输 入 的 密 码 正
] 键时，确定当前选择的数
] 键时，如果输入的密码正
] 键。
] 键， 主对讲机将显示"CLONE" 。
9