Kenwood NX-220 Service Manual page 8

NX-220
5. Check the connection between the transceiver and the
personal computer, and make sure that the transceiver is
in the Program mode.
6. Press "write" button in the window. When the transceiv-
er starts to receive data, the [LOADING] display lights.
7. If writing ends successfully, the checksum is calculated
and a result is displayed.
8. If you want to continue programming other transceivers,
repeat steps 4 to 7.
6-4. Function
If you press the [Side1] key while "FIRM PRG" is dis-
played, the checksum is calculated, and a result is displayed.
If you press the [Side1] key again while the checksum is
displayed, "FIRM PRG" is redisplayed.
Note:
• This mode cannot be entered if the Firmware Program-
ming mode is set to Disable in the Programming soft-
ware.
• Normally, write in the high-speed mode.
• The text message are displayed for C model only.
7. Clone Mode (C model only)
Programming data can be transferred from one transceiv-
er to another by connecting them via their external SP/MIC
connectors. The operation is as follows (the transmit trans-
ceiver is the source and the receive transceiver is a target).
The following data cannot be cloned.
• Tuning data
• Embedded message with password
• Model name data
• ESN (Electronic Serial Number) data
Note:
The following data can be cloned.
• Fleet (own)/ID (own) for FleetSync
• Unit ID (own) for NXDN
• ID (own) for MDC-1200
1. Press and hold the [
power ON. If the Read authorization password is set to
the transceiver, the transceiver displays "CLN LOCK".
If the password is not set, the transceiver displays
"CLONE".
2. When you enter the correct password, and "CLONE"
is displayed, the transceiver can be used as the cloning
source. The following describes how to enter the pass-
word.
3.
• How to enter the password using the keypad;
If one of keys 0 to 9 is pressed while the "CLN LOCK" is
displayed, the pressed number is displayed on the LCD.
Each press of the key shifts the display in order to the
left.
8
REALIGNMENT /
] key while turning the transceiver
模式组合
5. 检查手持对讲机与个人电脑之间的连接，确认手持对讲机
处于编程模式。
6. 按窗口中的"w r i t e"按钮。手持对讲机开始接收数据时，
显示 [LOADING]。
7. 如果写入操作成功完成，则计算校验和并显示结果。
8. 若要继续为其他手持对讲机编程，请重复步骤 4 至 7。
6-4. 功能
如果在显示"FIRM PRG"时按 [ 侧面 1] 键，则计算校验和
并显示结果。如果在显示校验和时再次按 [ 侧面 1] 键，则重
新显示"FIRM PRG" 。
注意 :
· 如果手持对讲机的固件编程模式设为禁用，则无法进入此
模式。
· 通常以高速模式写入。
· 文本信息显示仅限 C 型号。
7. 复制模式 ( 仅限 C 型号 )
用外部 SP/MIC 连接器连接手持对讲机，可以将编程数据从
一台手持对讲机传输到另一台手持对讲机。具体操作如下 ( 发
射机是主对讲机，接收机是子对讲机 )。
不能复制以下数据。
• 调谐数据
• 带密码的嵌入信息
• 机型数据
• ESN( 电子序列号 ) 数据
注意 :
可以复制以下数据。
• FleetSync 的 Fleet( 自身 )/ID( 自身 )
• NXDN 的 Unit ID( 自身 )
• MDC-1200 的 ID( 自身 )
1. 打开手持对讲机电源时，按住 [
设置了读取授权密码，则手持对讲机显示"CLN LOCK" 。
如果没有设置密码，则手持对讲机显示"CLONE" 。
2. 输入正确的密码后，显示"C L O N E" ，手持对讲机可以用作
复制源。以下介绍如何输入密码。
3.
• 如何使用键盘输入密码 ;
如果在显示"C L N L O C K"时按 0 至 9 当中的某个键，L C D
上将显示按下的数字。
每次按键依次向左移动显示。
] 键。如果手持对讲机