Ryobi RBC254SBSO Operator's Manual page 35

Deutsch (Übersetzung der originalen Anleitungen)
■ Use the tip of string to do the cutting; do not force
string head into uncut grass.
■ Wire and picket fences cause extra string wear, even
breakage. Stone and brick walls, kerbs and wood may
wear string rapidly.
■ Avoid trees and shrubs. Tree bark, wood mouldings,
cladding and fence posts can easily be damaged by
the string.
ADVANCING THE LINE
(See Fig 7)
TM
REELEASY
Line advance is controlled by tapping the string head on
grass while running engine at full throttle.
■ Run engine at full throttle.
■ Tap the knob on ground to advance string. The string
advances each time the knob is tapped. Do not hold
the knob on the ground.
OPERATING THE BRUSHCUTTER (See Fig 5-7)
RBC254SESO: Hold the product with the right hand on the
rear handle and the left hand on the front handle.
RBC254SBSO: Hold the product with the right hand on the
trigger handle and the left hand on the left handle.
Keep a fi rm grip with both hands while in operation. The
product should be held at a comfortable position with the
trigger handle about hip height. Maintain your grip and
balance on both feet. Position yourself so that you will not
be drawn off balance by the kick-back reaction of the cutting
blade.
Adjust the shoulder strap to position the product at a
comfortable operating position and to assure that the
shoulder strap will reduce the risk of operator contact with
the blade.
Exercise extreme caution when using the blade with this
unit. Blade thrust is the reaction which may occur when
the spinning blade contacts anything it cannot cut. This
contact may cause the blade to stop for an instant, and
suddenly "thrust" the unit away from the object that was hit.
This reaction can be violent enough to cause the
operator to lose control of the unit. Blade thrust may
occur without warning if the blade snags, stalls or binds.
This is more likely to occur in areas where it is diffi cult to
see the material being cut. For cutting ease and safety,
approach the weeds being cut from the right to the left.
In the event that an unexpected object or woody stock is
encountered, this could minimise the blade thrust reaction.
English (Original instructions)
TRI-ARC
The Tri-ArcTM blade is suited only for thicker weeds and
pulpy stalks. When the blade becomes dull, it can be
turned over to extend the life of the blade. Do not sharpen
the Tri-ArcTM blade.
CUTTING TECHNIQUE-BLADE
(See Fig 6)
■ Both hands must be used at all times to control this
■ Maintain your grip and balance on both feet. Position
■ Inspect and clear the area of any hidden objects such
■ Never use blades near footpaths, fencing, posts,
■ Never use a blade after hitting a hard object without
■ For cutting ease and safety, approach the weeds
MAINTENANCE
■ The cutting attachment must not work in idle mode.
■ You may make adjustments and repairs described
■ Consequences
33
TM BLADE
WARNING
The blades are very sharp and can injure even
if they are not moving. Exercise extreme caution
when using the blade with the product. Safe
operation of this tool requires that you read and
understand this operator's manual and all labels
affixed to the tool.
product. Keep a firm grip with both hands while in
operation.
yourself so that you will not be drawn off balance by
the kick-back reaction of the cutting blade.
as glass, stones, concrete, fencing, wire, wood, metal,
etc.
buildings or other immovable objects.
first inspecting it for damage. Do not use if any
damage is detected.
being cut from the right to the left.
WARNING
Use only original manufacturer's replacement
parts, accessories and attachments. Failure to
do so can cause possible injury, poor perfor-
mance and may void your warranty.
If this requirement is not satisfied, the clutch has
to be adjusted or the machine needs an urgent
maintenance by a qualified technician.
here. For other repairs, have the product serviced by
an authorized service agent.
of improper
include excess carbon deposits resulting in loss of
performance and discharge of black lubricant residue
maintenance may