Related Manuals for Ryobi RBC254FSDSN
Summary of Contents for Ryobi RBC254FSDSN
- Page 1 RBC254FSDSN TRIMMER / BRUSHCUTTER OPERATOR’S MANUAL (Original Instructions) Important! It is essential you read the instructions in this manual before starting, operating and maintaining this machine. Subject to technical modifications.
-
Page 2: General Safety Warnings
GENERAL SAFETY WARNINGS engine and the cutting attachment. ■ Dangerous Environments. To avoid falling, do not WARNING use the product in damp or wet locations. ■ Controlling the Product. During choke adjustments Read and understand all instructions. Failure to the cutting attachment may spin. Therefore, you should follow all instructions may result in serious personal wear protective equipment and observe all safety injury as well as damage to the product. - Page 3 SYMBOLS The following symbols are located on labels on the Use 2-stroke oil for air cooled engines. attachment shaft. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer. Mix the fuel mix thoroughly and also each time before refueling SYMBOL...
-
Page 4: Specifications
SPECIFICATIONS - Equivalent vibration 6.1 m/s 2 4.3 m/s 2 total value Weight without fuel 5.31 Kg and trimmer head Uncertainty 1.5 m/s Weight without fuel with trimmer Noise emission (in accordance with ISO 22868) 5.61 Kg head A-weight emission sound pressure level at the Fuel tank volume 620 cm operator's position... - Page 5 FIGURE 11 ATTACHING THE FRONT HANDLE (FIG. 2) 20. Foam air filter ■ Remove the two securing bolts (item 6) from the front 21. Air filter cover handle (item 5). 22. Cover securing knob ■ Position the front handle (item 5) onto the upper shaft (item 1).
- Page 6 And watch the video; of the line trimmer head and push until line comes out RYOBI: How to install trimming line on a Pro-Cut II™ head through the eyelet on the other side. Continue to push line through the line trimmer head until the middle...
-
Page 7: Operation
OPERATION ■ Remove the cutting head housing (item 30). ■ Align the slot in the upper flange washer (item 31) with FUEL AND REFUELING the hole in the gear head (item 32). Insert the holding pin (item 33) through the slot in the upper flange Handling the fuel safely washer and the hole in the gear head. -
Page 8: To Start A Cold Engine
Note: It is normal for smoke to be emitted from a new NOTE: When the engine starts, let it run for 30 seconds engine during and after first use. prior to operation. TO START A WARM ENGINE WARNING Follow these steps to start a warm engine: Always shut off engine before fueling. -
Page 9: General Maintenance
■ Place the product on the right side of your body with hit. This reaction can be violent enough to cause the the engine behind and away from your body. operator to lose control of the unit. Blade thrust may occur without warning if the blade snags, stalls or binds. -
Page 10: Checking The Fuel Cap
this manual. For other repairs, have the trimmer serviced CAUTION by an authorised service dealer. Be careful not to cross-thread the spark plug. Cross- CLEANING THE AIR FILTER (FIG. 11) threading will seriously damage the engine. A dirty air filter will cause starting difficulty, loss of performance, and shorten the life span of the engine. -
Page 11: Troubleshooting
TROUBLE SHOOTING PROBLEM POSSIBLE CAUSE SOLUTION 1. Switch set to the O (OFF) position. 1. Set switch to the I (ON) position. 2. No spark 2. Remove the spark plug. Reattach the spark plug cap and lay the spark plug on the metal cylinder. Pull the starter cord and watch for a spark at the spark plug tip. - Page 12 Techtronic Industries (Australia) Pty. Ltd. Level 1, 660 Doncaster Road Doncaster, VIC 3108, Australia Techtronic Industries New Zealand Ltd. 18-26 Amelia Earhart Avenue Mangere, Auckland 2022, New Zealand 960710005-03...