Utility Output Command; Installer's Programming Commands [ ]+[8]+[Installer's Code]; At Home" Arming; Quick Arm" Command - DSC PC2550 Installation Manual

Utility Output Command

[ ]+[7] OR [ ]+[7]+[ACCESS CODE]
The programmable output (PGM terminal) on the PC2550
can be made to activate by a command from the keypad.
This output can be used for operating other devices such as
garage door opener, special lighting or door strikes.
The programmable output must be selected for keypad
utility using the [ ][8][Installer's Code][30] command and
programming a [2], [3], [4] or [5].
Depending on the option chosen in the programming
section, the programmable output is activated by pressing
the [ ] then [7] keys followed by a Group A access code,
Group B access code, any access code, or no code at all.
When the proper keys are pressed the keypad sounder and
the programmable output are activated for 5 seconds.
Installer's Programming Commands
[ ]+[8]+[INSTALLER'S CODE]
The PC2550 is completely programmed from the keypad by
using commands in the [ ] [8] section. The commands are
described in detail in the programming section of this
manual.

"At Home" Arming

[ ]+[9]+[ACCESS CODE]
Entering [ ], [9] before the arming code, arms the panel
without any entry delay on the delay zones and bypasses
zones that are defined as "Home-Away". This command is
used for arming the system while at home. When the panel
is armed using [ ], [9], the "Armed" light will be on flashing
and the bypass light will be on to indicate that the "Home-
Away" zones are bypassed. Once the panel is Armed in this
mode, using [ ], [1] will remove the bypass from those
zones defined as "Home-Away" if they have NOT been
manually bypassed. The [ ], [1] command used here, only
removes the bypass from zones that have been
Automatically bypassed with the [ ], [9] command."

"Quick Arm" Command

[ ]+[0]
Entering [ ][0] is accepted as a valid arming code when the
"Quick Arm" feature is activated. Quick Arm may be used
as a convenience for regular users or when the system is to
be armed by individuals who are not authorized to disarm
the system. See instructions in the "[ ][6] User's Functions
Command" section for activating the "Quick Arm" feature.
This feature should not be enabled if the One Time Use
Code is enabled. The One Time Use Code must be used for
arming before it is erased.

Quick Exit

[ ]+[0] When Armed
Entering [ ] [0] when the system is fully armed will allow the
user 2 minutes to exit the premises through any delay zone
without altering the status of the system if the Quick Exit
feature is enabled. The Quick Exit feature can be enabled
by turning on light 1 in section [18]. After [ ] [0] is entered
into an armed system, one and only one delay zone may be
tripped. Any additional activity on any other active zone will
cause that zone to begin its alarm sequence.
[ ] [0] for Quick Exit on a partially armed system is not
supported.
Quick Exit is not designed to extend the standard Exit Delay.
It must not be used when auxiliary delay zones are force
armed. Turn light 6 in section [17] off to ensure proper
operation.

Keypad Zones

There are three zones which can be activated from the
keypad. The alarm and restoral codes for keypad zones are
programmed using the [ ][8] command.
Pressing the [F] key or the [1] and [3] keys for 2 seconds
activates a Fire alarm. The fire alarm sounds the siren/bell in
a pulsed mode and is annunciated as a memory condition.
The Fire key can be turned off in section [18].
Pressing the [A] key or the [4] and [6] keys for 2 seconds
activates an Auxiliary keypad zone. If a reporting attempt is
made to an alarm receiver and it is successful the PC2550
will acknowledge the transmission with a short series of
beeps from the keypad.
Pressing the [P] key or the [ ] and [#] keys for 2 seconds
activates the Police (or Panic) alarm. The panic alarm can
be programmed for audible or silent operation (see sections
[15] and [18] in "Programming Guide").
There is no light annunciation from the keypad for the last
two keypad zones, however, the keypad buzzer beeps 3
times to confirm activation on any of the keypad zones.
See section [11] for alarm and restoral codes for all three
keypad zones.
11