Table of Contents
Advertisement
K
E
Y
• [3] – Auto-Arm Time
The system can be programmed to Auto-Arm at a
certain time. When programming the auto-arming time,
enter the time (hour and minute) using military format
[HH MM]. For more information, see Section 3.3 –
"Auto-Arming".
• [4] – System Test
When [4] is pressed the panel will test the bell output,
keypad lights and the communicator for two seconds.
The panel will also send a System Test Reporting
code, if programmed (see Section 5.7 – "Communica-
tor – Reporting Codes").
• [5] – Enable DLS (Downloading)
When [5] is pressed, the panel will enable the down-
loading option for one hour. During this time the panel
will answer incoming downloading calls (see Section
5.9 "Downloading").
• [6] – User Initiated Call-Up
When [6] is pressed, the panel will initiate call-out to
the downloading computer.
• [7] – Last Code to Disarm and Arm
Pressing [7] will display the last code to disarm the
system. Then, pressing [9] will display the last code to
arm the system.
• [0] – Walk Test Enable / Disable
The Installer Walk Test can be used to verify that each
zone of the panel is functioning properly. Any zone
violated during a walk test will cause the panel to
activate the Bell Output for two seconds, log the event
to the Event Buffer and communicate the alarm to
central station. Do not tamper or fault zones while in
walk test. You can exit walk test with zones open. You
can cancel walk test by arming with all zones restored.
Additional Features using the LCD Keypad
Additional features, including access to the Event Buffer, are
available using the LCD keypad. Use the arrow keys (< >) to
scroll through the [ ] [6] menu and press the [ ] key to select
the following commands:
Viewing the Event Buffer from an LCD Keypad
Select "View Event Buffer" from the [ ] [6] menu. The
keypad will display the event, event number, time and date
along with the zone number and user code, if applicable.
Press [ ] to toggle between this information and the event
itself. Use the arrow keys (<>) to scroll through the events
in the buffer. When you have finished viewing the Event
Buffer, press the [#] key to exit.
Brightness Control
The LCD keypad will allow you to select from 10 different
backlighting levels. Use the arrow keys (< >) to scroll to the
desired backlighting level and press the [#] key to exit.
Contrast Control
The LCD keypad will allow you to select from 10 different
display contrast levels. Use the arrow keys (< >) to scroll to
the desired contrast level and press the [#] key to exit.
Keypad Beeper Control
The LCD keypad will allow you to select from 21 different
keypad beeper tones. Use the arrow keys (< >) to scroll to
the desired keypad beeper level and press the [#] key to
exit. This featured can be accessed on LED keypads by
holding the [ ] key.
P
A
D
V
C
O
[ ] [7]
There are two output functions available to the user: Utility
Output and Sensor Reset.
To activate Utility Output:
Press [ ] [7] [1][Access Code].
The panel will activate all PGM Outputs programmed as
utility outputs for five seconds (see Section 5.10 – "PGM
Outputs").
To activate Sensor Reset:
Press [ ] [7] [2].
The panel will activate all PGM Outputs programmed as
Sensor Reset for five seconds.
This function can also be performed by pressing and
holding the Reset function key for two seconds on any
PC5506T or LCD5500T keypad.
[ ] [8]
Enter [ ] [8] followed by the Installer's Code to enter this
function. Installer's Programming is outlined in detail in
Sections 4 and 5 of this manual.
[ ] [9]
When the system is armed with the [ ] [9] command, the
panel will cancel the entry delay. Once the exit delay has
expired, Delay 1 and Delay 2 type zones will be instant and
Stay/ Away zones will be bypassed (see Section 5.2 – "Zone
Definitions"). A valid access code must be entered after
pressing [ ] [9].
[ ] [0]
If the Quick Arm option is enabled, the panel can be armed
without a user code by entering [ ] [0] (See Section 5.15
"Arming / Disarming Options").
Quick Arm cannot be used to cancel Auto Arm.
Quick Exit
The Quick Exit function, if enabled, will allow someone to
leave an armed premises through a Delay type zone without
having to disarm and rearm the system (See Section 5.15
"Arming / Disarming Options").
When [ ] [0] is entered, the panel will provide a two minute
window for the user to exit the premises. During this time, the
panel will ignore only one activation of a Delay zone. When
the Delay zone is secured, the panel will end the two minute
quick exit delay.
If a second Delay zone is tripped or if the zone is not restored
after two minutes, the panel will begin the entry delay.
If the Exit Delay is in progress, performing a Quick
Exit will not extend the Exit Delay.
3.5 Function Keys
The function keys only appear on the PC5506T and
LCD5500T keypads
There are five function keys on the PC5506T and LCD5500T
keypads located to the right of the number pad labelled
Stay, Away, Chime, Reset and Exit. Each of these keys are
programmed by default to perform one of the functions
10
M
M
A
Output Functions
Installer's Programming
Arming Without Entry Delay
Quick Arm
N
D
S
Advertisement
Table of Contents
