5Th System Option Code; Answering Machine Over-Ride Timer; System Test Code And Tlm Restoral Code; Access Bypass Mask (Codes 1 To 8) - DSC PC2550 Installation Manual

Smoke detectors on the Fire Zone are powered from the
SW AUX terminal. When the [ ][4] Command is entered,
power will be removed from the smoke detectors to allow
them to be reset. When the [ ][4] Command is used,
the Fire Zone Trouble normally generated from a power
supervision relay when power is removed from the
smoke detector is not displayed or communicated.
* Off = Fire Zone Not Connected to SW AUX.
[3] Escort Access Code Options
On = Escort Requires Master Code. The Escort voice
assisted security control module will only allow remote
access to the system if the Master Code is entered.
* Off = Escort Accepts Any Access Code. The Escort
voice assisted security control module will allow remote
access to the system for any valid access code.
[4] - [6] For Future Use
[7] Test Transmission Options
On = Test Transmission Enabled.
The system will automatically call the programmed
telephone numbers and transmit the Test Reporting
Code programmed in the Maintenance Alarms Reporting
Codes Section at the time programmed in the System
Clock Times and at the interval, in days, programmed in
the System Times.
* Off = Test Transmission Disabled.
[8] Periodic Downloading Options
On = Periodic Downloading Enabled.
The system will automatically place a call to the
downloading computer at the time programmed in the
System Clock Times and at the interval, in days,
programmed in the System Times. A Downloading
Telephone Number must be programmed in the
Downloading Computer Telephone Number Section.
* Off = Periodic Downloading Disabled.
* is default condition.
[49] Answering Machine Over-ride
Timer
This timer sets the amount of time that can be taken
between calls when using the answering machine over-ride
(see section [47] light 7 description). Valid entries are from
001 to 249 (in seconds) with a default of 060.
[50] System Test Code and TLM
Restoral Code
This section is programmed the same as section [05].
System Test Code
Once a valid code is programmed into the system test code
it will be sent to the central station every time that a system
test is done ([ ]+[6]+[Master Code]+[8]).
TLM Restoral Code
Once a valid code is programmed into the TLM restoral
code it will be sent to the central station every time that the
phone line trouble is restored. This will also initiate
transmission of all codes unsuccessfully transmitted during
the phone line fault.
[52] Access Bypass Mask (Codes 1 to
8)
Use the same method of programming as used in section
[19]. In this section it is possible to control which access
codes can be used to bypass zones. If the zone light is on
that access code can be used to bypass. Zone light 8 in
section [16] must be on to enable access bypassing with an
access code.
[53] Access Bypass Mask
(Codes 9 to 16)
Use the same method of programming as used in section
[52].
Note: Zone lights 1 to 8 represent codes 9 to 16. Note: Zone lights 1 to 8 represent codes 9 to 16. Note: Zone lights 1 to 8 represent codes 9 to 16. Note: Zone lights 1 to 8 represent codes 9 to 16. Note: Zone lights 1 to 8 represent codes 9 to 16.

[54] TLM Trouble Reporting Code

This reporting code can be transmitted to the monitoring
station through a LINKS 1000 Cellular Alarm Transmitter,
when a TLM trouble occurs on the regular phone lines.
Leave this section blank if there is no LINKS unit connected.
See section [05] for programming reporting codes and
"Trouble Display [ ]+[2]" for a description of TLM trouble.
[55] LINKS Test Transmission
Reporting Code
This reporting code is transmitted to the monitoring station
through a LINKS 1000 Cellular Alarm Transmitter periodically
for testing the cellular communications. The cellular test
transmission occurs at the same time as the regular test
transmission. The test transmission time is programmed in
sections [20] and [23]. After the cellular test transmission is
completed, the periodic test transmission reporting code
programmed in section [12] will be transmitted through the
regular phone lines.
LINKS 1000 Preamble Codes
They are 4-digit codes used with long distance telephone
numbers that are dialled through the LINKS module. These
codes are used for programming area codes in cases
where a land line telephone number may be a local call,
while the cellular telephone number dialled by the LINKS
1000 module is a long distance call.
In the following sections [56], [57] and [58], program 4-digit
Preambles for the Phone Numbers. Program all unused
digits with hexadecimal "F".
[56] LINKS 1000 Preamble for
1st Phone Number
[57] LINKS 1000 Preamble for
2nd Phone Number
[58] LINKS 1000 Preamble for
25