Motorola ASTRO XTL 5000 Basic Service Manual page 9

List of Figures xiii
Figure 8-9. Front Panel Reassembly...................................................................................................... 8-9
Figure 8-10. Removing the Control Head Screws .................................................................................. 8-10
Figure 8-11. Removing the Control Head............................................................................................... 8-10
Figure 8-12. Removing the Flex (Control Head Connector) ................................................................... 8-11
Figure 8-13. Removing the Headbridge ................................................................................................. 8-11
Figure 8-14. Removing the Flex (Main-Board Connector)...................................................................... 8-12
Figure 8-15. Removing the Headbridge Seal ......................................................................................... 8-12
Figure 8-16. Removing the Secure Interface Board ............................................................................... 8-13
Figure 8-17. Removing the Top Cover Screws....................................................................................... 8-14
Figure 8-18. Lifting the Top Cover .......................................................................................................... 8-14
Figure 8-19. Removing the J2 Rear Accessory Flex from the Main Board ............................................ 8-15
Figure 8-20. Removing the PA Screws................................................................................................... 8-16
Figure 8-21. Removing the RF/DC Retention Clips................................................................................ 8-16
Figure 8-22. Pushing Up the Main Board ............................................................................................... 8-17
Figure 8-23. Removing the J2 Rear Accessory Connector .................................................................... 8-17
Figure 8-24. Removing the Transceiver Interface Board Screws ........................................................... 8-18
Figure 8-25. Removing the Transceiver Interface Board Assembly ....................................................... 8-19
Figure 8-26. Removing the Flex (Transceiver Interface Board Connector) ............................................ 8-19
Figure 8-27. Removing the Flex (Main-Board Connector)...................................................................... 8-20
Figure 8-28. Removing the Front Panel Seal ......................................................................................... 8-20
Figure 8-29. Removing the Secure Interface Board ............................................................................... 8-21
Figure 8-30. Removing the Top Cover Screws....................................................................................... 8-22
Figure 8-31. Lifting the Top Cover .......................................................................................................... 8-22
Figure 8-32. Removing the PA Screws................................................................................................... 8-23
Figure 8-33. Removing the RF/DC Retention Clips................................................................................ 8-23
Figure 8-34. Pushing Up the Main Board ............................................................................................... 8-24
Figure 8-35. Inspecting the Chassis Shield Gasketing and Thermal Pads ............................................ 8-25
Figure 8-36. Inserting the J2 Rear Accessory Connector....................................................................... 8-26
Figure 8-37. Inserting the Main Board into the Chassis ......................................................................... 8-27
Figure 8-38. Connecting the J2 Rear Accessory Connector Flex to the Main Board ............................. 8-28
Figure 8-39. Inserting the RF/DC Retention Clips .................................................................................. 8-29
Figure 8-40. Inserting the RF/DC Retention Clip (DC Side) ................................................................... 8-29
Figure 8-41. Installing the PA Screws..................................................................................................... 8-30
Figure 8-42. Inspecting the Thermal Pad and Installing the Cover Main Seal ....................................... 8-30
Figure 8-43. Securing the Top Cover to the Chassis.............................................................................. 8-31
Figure 8-44. Installing the Secure Interface Board ................................................................................. 8-32
Figure 8-45. Installing the Headbridge Seal ........................................................................................... 8-32
Figure 8-46. Installing the control head Flex in the Transceiver ............................................................. 8-33
Figure 8-47. Installing the Headbridge on the Transceiver..................................................................... 8-33
Figure 8-48. Installing the Control Head Flex on the Control Head........................................................ 8-34
Figure 8-49. Inserting the Control Head Into the Transceiver ................................................................ 8-34
Figure 8-50. Installing the Control Head Screws .................................................................................... 8-35
Figure 8-51. Inspecting the Chassis Shield Gasketing and Thermal Pads ............................................ 8-35
Figure 8-52. Inserting the Main Board into the Chassis ......................................................................... 8-36
Figure 8-53. Inserting the RF/DC Retention Clips .................................................................................. 8-36
Figure 8-54. Inserting the RF/DC Retention Clip (DC Side) ................................................................... 8-37
Figure 8-55. Installing the PA Screws..................................................................................................... 8-37
Figure 8-56. Inspecting the Thermal Pad and Installing the Cover Main Seal ....................................... 8-38
Figure 8-57. Installing the Secure Interface Board ................................................................................. 8-39
Figure 8-58. Installing the Front Panel Seal ........................................................................................... 8-39
Figure 8-59. Installing the TIB Flex in the Transceiver ........................................................................... 8-40
Figure 8-60. Installing the Transceiver Interface Board Assembly Screws ............................................ 8-40
Figure 8-61. Chassis Thermal Pad Locations ........................................................................................ 8-41
Figure 8-62. Chassis Thermal Pad Locations ........................................................................................ 8-43
6871769L01-A October 30, 2006