Motorola ASTRO XTL 5000 Basic Service Manual page 8

xii
List of Figures
Figure 1-1. XTL 5000 O3 Control Head.................................................................................................. 1-4
Figure 1-2. XTL 5000 Control Head ....................................................................................................... 1-5
Figure 3-1. Controller Sections (Mid Power) .......................................................................................... 3-3
Figure 3-2. Controller Sections (High Power) ......................................................................................... 3-3
Figure 3-3. Audio Receive Path in XTL 5000 Transceiver...................................................................... 3-6
Figure 3-4. Audio Transmit Path in XTL 5000 Transceiver..................................................................... 3-7
Figure 3-5. O3 Dash Mount Configuration............................................................................................ 3-12
Figure 3-6. O3 Remote Mount Configuration ....................................................................................... 3-13
Figure 3-7. Single O3 Control Head + VIPS ......................................................................................... 3-14
Figure 3-8. Single O5 Control Head + VIPS ......................................................................................... 3-15
Figure 3-9. Multiple O5 Control Heads + VIPS..................................................................................... 3-15
Figure 3-10. Single Control Head + VIPS............................................................................................... 3-16
Figure 3-11. Single O3 Control Head + DEK + VIPS ............................................................................. 3-17
Figure 3-12. Single O5 Control Head + DEK + VIPS ............................................................................. 3-17
Figure 3-13. Multiple Control Heads + DEK +VIPS ................................................................................ 3-18
Figure 3-14. Two node system with CAN terminations enabled. ............................................................ 3-19
Figure 3-15. CAN Termination Section. .................................................................................................. 3-19
Figure 3-16. Control Head Interface Board (CHIB) ................................................................................ 3-20
Figure 3-17. Control Head Universal Connector (CHUC)....................................................................... 3-21
Figure 3-18. Transceiver Interface Board (TIB) ...................................................................................... 3-22
Figure 3-19. VHF Frequency Generation Unit Diagram ......................................................................... 3-28
Figure 3-20. UHF Frequency Generation Unit Diagram ......................................................................... 3-29
Figure 3-21. 700-800 MHz Frequency Generation Unit Diagram .......................................................... 3-30
Figure 5-1. Performance Checks Test Setup.......................................................................................... 5-1
Figure 5-2. XTL 5000 O3 Control Head.................................................................................................. 5-5
Figure 5-3. XTL 5000 Control Head ....................................................................................................... 5-6
Figure 6-1. Radio Alignment Test Setup ................................................................................................. 6-1
Figure 6-2. VHF/700-800 MHz Tuner Main Menu .................................................................................. 6-2
Figure 6-3. UHF Tuner Main Menu......................................................................................................... 6-2
Figure 6-4. Radio Information Screen .................................................................................................... 6-3
Figure 6-5. PA Bias 1 Alignment Screen ................................................................................................ 6-4
Figure 6-6. PA Bias 2 Alignment Screen ................................................................................................ 6-6
Figure 6-7. PA Bias 3 Alignment Screen ................................................................................................ 6-7
Figure 6-8. Reference Oscillator Window ............................................................................................... 6-9
Figure 6-9. Power Detection Calibration Alignment Screen ................................................................. 6-11
Figure 6-10. Tx Power Characterization Alignment Screen ................................................................... 6-12
Figure 6-11. Tx Current Limit Alignment Screen .................................................................................... 6-14
Figure 6-12. Tx Deviation Balance (Compensation) Alignment Screen ................................................. 6-16
Figure 6-13. Tx Deviation Limit Alignment Screen ................................................................................. 6-18
Figure 6-14. Rx Front-End Filter Alignment Screen ............................................................................... 6-19
Figure 6-15. Bit Error Rate Screen ......................................................................................................... 6-20
Figure 6-16. Transmitter Test Pattern Screen......................................................................................... 6-21
Figure 8-1. Cable Lock Detachment ....................................................................................................... 8-2
Figure 8-2. Front Housing and Back Housing Detachment .................................................................... 8-3
Figure 8-3. Separate Front Housing and Back Housing ......................................................................... 8-3
Figure 8-4. PCB Detachment.................................................................................................................. 8-4
Figure 8-5. Disconnecting the 2-pin Connector ...................................................................................... 8-4
Figure 8-6. Control Head Screw Sequence ............................................................................................ 8-5
Figure 8-7. Front Panel Disassembly ..................................................................................................... 8-7
Figure 8-8. TUC Seal Placement............................................................................................................ 8-8
October 30, 2006
List of Figures
6871769L01-A