: y l - " i t a o i t i t a e l r l l a L " " 2 " 8 : t h SKU 46446 Page 2 For technical questions and replacement parts, please call 1-800-444-3353...
Store idle equipment. When not in use, tools must be stored in a dry location to inhibit rust. Always lock up tools and keep out of reach of children. SKU 46446 Page 3 For technical questions and replacement parts, please call 1-800-444-3353...
Page 4
Any part that is damaged should be properly repaired or replaced by a qualified technician. Do not use the tool if the throttle lever does not function properly. SKU 46446 Page 4 For technical questions and replacement parts, please call 1-800-444-3353...
Page 5
* Crystalline silica from bricks and cement or other masonry products * Arsenic and chromium from chemically treated lumber (California Health & Safety Code 25249.5, et seq. ) SKU 46446 Page 5 For technical questions and replacement parts, please call 1-800-444-3353...
Page 6
CAUTION: Turn off your air compressor and disconnect the air pressure hose before changing attachments or making any adjustments to these tools. Severe injury or property damage may otherwise result. SKU 46446 Page 6 For technical questions and replacement parts, please call 1-800-444-3353...
When the nut is removed, stop the Impact Wrench by releasing the Trigger and remove the Impact Wrench from the nut. Remove the nut from the socket if needed. SKU 46446 Page 7 For technical questions and replacement parts, please call 1-800-444-3353...
Page 8
Impact Wrench. 1/2” Air Impact Wrench Parts List l i v l f f " " l i v " " l n I SKU 46446 Page 8 For technical questions and replacement parts, please call 1-800-444-3353...
Page 9
NOTE: Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts. Some parts are available only as part of an assembly. SKU 46446 Page 9 For technical questions and replacement parts, please call 1-800-444-3353...
Page 10
Trigger (24a). The Drill will begin to operate, and the drill bit will begin to drill into the work material. Drill until you have reached the desired depth. Release the Trigger (24a) to cease operation of the drill. SKU 46446 Page 10 For technical questions and replacement parts, please call 1-800-444-3353...
Page 11
3/8” Reversible Air Drill Parts List " " " " " " NOTE: When ordering parts for this drill, always use the “a” suffix, for example, Chuck Screw is part #17a. SKU 46446 Page 11 For technical questions and replacement parts, please call 1-800-444-3353...
Page 12
AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. SKU 46446 Page 12 For technical questions and replacement parts, please call 1-800-444-3353...
Page 13
Turn off the air compressor and disconnect the tool from the air supply hose. Release the Safety (8b) and press the Trigger (4b) to release any trapped air from the tool. SKU 46446 Page 13 For technical questions and replacement parts, please call 1-800-444-3353...
Page 14
NOTE: When ordering parts for this grinder, always use the “b” suffix, for example, Housing is part #17b. SKU 46446 Page 14 For technical questions and replacement parts, please call 1-800-444-3353...
Page 15
Brought to You by www.snapwhole.com 1/4” Air Die Grinder Assembly Diagram NOTE: When ordering parts for this grinder, always use the “b” suffix, for example, Housing is part #17b SKU 46446 Page 15 For technical questions and replacement parts, please call 1-800-444-3353...
Page 16
Sander to move in an orbital motion, position the flat edge of the Orbital Hub (41c) against the round edge of the Drive Spindle (38c). Please see the photo. SKU 46446 Page 16 For technical questions and replacement parts, please call 1-800-444-3353...
Page 17
Each successive grit is used to lower the “hills” of the previous grit to the grain size of the new, finer grit. Continue this process, using successively finer grits until the desired finish is achieved. SKU 46446 Page 17 For technical questions and replacement parts, please call 1-800-444-3353...
Page 18
" " O NOTE: When ordering parts for this sander, always use the “c” suffix, for example, Trigger is part #16c. SKU 46446 Page 18 For technical questions and replacement parts, please call 1-800-444-3353...
Page 19
Brought to You by www.snapwhole.com 6” Dual Action Air Sander Assembly Diagram NOTE: When ordering parts for this sander, always use the “c” suffix, for example, Trigger is part #16c. SKU 46446 Page 19 For technical questions and replacement parts, please call 1-800-444-3353...
Page 20
Note: Before connecting the air supply, make sure you are wearing safety goggles and a full face mask, ear protection, and steel toe shoes. SKU 46446 Page 20 For technical questions and replacement parts, please call 1-800-444-3353...
Before storage, add a small quantity of high quality pneumatic oil in the Air Inlet (9d) and operate the tool for a couple of seconds to lubricate and protect the internal mechanism. SKU 46446 Page 21 For technical questions and replacement parts, please call 1-800-444-3353...
Page 22
Air Hammer Parts List Air Hammer Assembly Diagram NOTE: When ordering parts for this Air Hammer, always use the “d” suffix, for example, Body is part #1d. SKU 46446 Page 22 For technical questions and replacement parts, please call 1-800-444-3353...
Page 23
NOTE: Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts. Some parts are available only as part of an assembly. SKU 46446 Page 23 For technical questions and replacement parts, please call 1-800-444-3353...