Table of Contents
Advertisement
I I n n s s t t a a l l l l a a t t i i o o n n : : C C o o n n t t r r o o l l s s
Installing the Tracer AdaptiView
Display
During shipment, the Tracer® AdaptiView™ display is
boxed, shrink-wrapped, and located behind the control
panel. The display must be installed at the site.
I I m m p p o o r r t t a a n n t t : : For best results, Trane, or an agent of
Trane, must install the Tracer®
AdaptiView™ display and support arm.
1. Unwrap the control panel and display arm. Locate
the box containing the Tracer® AdaptiView™
display behind the control panel (labeled A in the
following figure).
2. After the box containing the display has been
removed, remove the shipping bracket from the
back of the control panel (labeled B in the following
figure).
3. Remove the display from the box.
N N o o t t e e : : Display screws are M4 (metric size 4), 6 to
8 mm long, and are shipped with the display.
4. Plug the power cable (labeled C in the following
figure) and the Ethernet cable (labeled D in the
following figure) into the bottom of the display.
N N o o t t e e : : Both cables are already present and extend
from the end of the display arm.
5. Adjust the Tracer® AdaptiView™ display support
arm so the base plate that attaches to the display is
horizontal.
C C A A U U T T I I O O N N
T T e e n n s s i i o o n n i i n n D D i i s s p p l l a a y y S S u u p p p p o o r r t t A A r r m m ! !
F F a a i i l l u u r r e e t t o o f f o o l l l l o o w w i i n n s s t t r r u u c c t t i i o o n n s s b b e e l l o o w w c c o o u u l l d d
r r e e s s u u l l t t i i n n u u n n e e x x p p e e c c t t e e d d m m o o v v e e m m e e n n t t o o f f t t h h e e s s p p r r i i n n g g - -
l l o o a a d d e e d d s s u u p p p p o o r r t t a a r r m m w w h h i i c c h h c c o o u u l l d d r r e e s s u u l l t t i i n n m m i i n n o o r r
t t o o m m o o d d e e r r a a t t e e i i n n j j u u r r y y . .
E E n n s s u u r r e e t t h h a a t t t t h h e e s s u u p p p p o o r r t t a a r r m m i i s s i i n n t t h h e e f f u u l l l l
u u p p r r i i g g h h t t p p o o s s i i t t i i o o n n w w h h e e n n r r e e m m o o v v i i n n g g t t h h e e T T r r a a c c e e r r
A A d d a a p p t t i i V V i i e e w w d d i i s s p p l l a a y y f f r r o o m m t t h h e e s s u u p p p p o o r r t t a a r r m m . .
N N o o t t e e : : Review
"Adjusting the Tracer AdaptiView
Display Arm," p. 51
display as some adjustments may be
required prior to attaching the display to the
support arm base.
6. Position the Tracer® AdaptiView™ display—with
the LCD screen facing up—on top of the display
support arm base plate.
N N o o t t e e : : Ensure the Trane logo is positioned so that it
will be at the top when the display is attached
to the display support arm.
I I m m p p o o r r t t a a n n t t : : Use care when positioning the Tracer®
AdaptiView™ display on top of the
support arm base plate and do NOT
drop the display.
7. Align the four holes in the display with the screw
50
before attaching the
holes in the display support arm base plate.
8. Attach the Tracer® AdaptiView™ display to the
display support arm base plate (labeled E in the
following figure) using the M4 (metric size 4)
screws referenced in step 3.
Figure 35. Tracer AdaptiView shipping location
Figure 36. Power cable and Ethernet cable
connections
A
B
CDHF-SVX01N-EN
Advertisement
Table of Contents
