Fault Memory And Retrieval; Operating Tips - Toro Reelmaster 6700-D Operator's Manual

4-wheel drive traction unit
Hide thumbs Also See for Reelmaster 6700-D:
Table of Contents

Advertisement

output LEDs should illuminate to indicate that
the ECU is turning on that function. (Refer to
Hydraulic Solenoid Valve Functions (page 29)
be certain of the specified output LEDs.)
Note:
If any output LED is blinking, this
indicates an electrical problem with that
OUTPUT. Repair/replace defective electrical
parts immediately. To reset a blinking LED,
turn the key switch "Off", then back "On" and
clear the controllers fault memory; refer to
Memory and Retrieval (page
If no output LEDs are blinking, but the correct
output LEDs do not illuminate, verify that the
required input switches are in the necessary
positions to allow that function to occur. Verify
correct switch function.
If the output LEDs are on as specified, but
the machine does not function properly, this
indicates a non-electrical problem. Repair as
necessary.
Note:
Due to electrical system constraints,
the output LEDs for "Start", "Preheat" and
"ETR/ALT" may not blink even though an
electrical problem may exist for those functions.
If the machine problem appears to be with one of
these functions, be certain to check the electrical
circuit with a volt/ohm meter to verify that no
electrical problem exists to these functions.
If each input switch is in the correct position and
functioning correctly, but the output LEDs are
not correctly illuminated, this indicates an ECU
problem. If this occurs, contact your authorized
Toro distributor for assistance.

Fault Memory and Retrieval

If the Controller senses a fault on one of the output
solenoids, it will flash the machines diagnostic
Lamp (Reel Diagnostic Lamp on console or Green
Diagnostic Lamp under console) and store the fault
into the Controller's (ECU) memory. The fault can
then be retrieved and viewed with the Diagnostic
ACE handheld tool or a laptop/PC at anytime. The
Controller will store 1 fault at a time and will not store
another different fault until the first fault is cleared.
Retrieving Fault Information
Retrieving Stored Faults (Do not sit in seat)
1.
Rotate the key to the O
2.
Connect the Handheld Diagnostic Tool to the
desired Controller Loop-back Connector (use
the proper overlay).
3.
Move the lower mow/raise control lever to the
R
position and hold it there.
AISE
Fault
27).
position.
FF
4.
Rotate the key to the O
to hold the lower mow/raise control lever in the
to
R
position until the top left Diagnostic Tool
AISE
light comes on (approximately 2 seconds).
5.
Release the lower mow/raise control lever to the
center position.
6.
The Handheld Tool will now play back the fault
retained in the Controller memory.
Important:
individual records with the fault displayed
on the 8th record. Each record will be
displayed for 10 seconds. Be sure to have
the Diagnostic Tool display on Outputs to see
fault. The Problem circuit will be flashing.
Records will repeat until the key is turned
off. The machine will not start in this mode.
Clearing the Fault Memory (Diagnostic Tool
not required)
7.
Rotate the key to the O
8.
Turn Backlap Switch to the Front or Rear
Backlap position.
9.
Turn the Reel Control Switch to Enable position.
10.
Move the lower mow/raise control lever to the
Raise position and hold.
11.
Turn the key to On, and continue to hold the
lower mow/raise control lever in the R
position until the Reel Control Lamp starts to
flash (approximately 2 seconds).
12.
Release the lower mow/raise control lever and
turn the key to the O
now cleared.
13.
Turn the Backlap Switch to the O
the Enable Switch to the D
Important:
ACE display connected to the machine. It is
not designed to withstand the environment
of the machine's everyday use. When you
are finished using the Diagnostic ACE,
disconnect it from the machine and connect
the loop-back connector to the harness
connector. The machine will not operate
without the loop-back connector installed
on the harness. Store the Diagnostic ACE
in a dry, secure location indoors, not on the
machine.

Operating Tips

Becoming Familiarized with the
Machine
Before mowing grass, practice operating the machine
in an open area. Start and shut off the engine.
27
position, and continue
N
The display will show eight (8)
position.
FF
position. The memory is
FF
FF
position.
ISABLE
Do not leave the Diagnostic
AISE
position and

Advertisement

Table of Contents
loading

This manual is also suitable for:

03813

Table of Contents