Sign In
Upload
Download
Table of Contents
Contents
Add to my manuals
Delete from my manuals
Share
URL of this page:
HTML Link:
Bookmark this page
Add
Manual will be automatically added to "My Manuals"
Print this page
×
Bookmark added
×
Added to my manuals
Manuals
Brands
Omega Manuals
Temperature Controller
CN8200 Series
User manual
Supervisor Menu; Calibration Menu; Options Menu - Omega CN8200 Series User Manual
1/16 din temperature & process controllers
Hide thumbs
Omega
CN8200 Series
User Manual
1
2
3
Table Of Contents
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
page
of
29
Go
/
29
Contents
Table of Contents
Bookmarks
Table of Contents
Advertisement
Recipe (Ramp/
NOTE: The following seven parameters are only available when
Soak) Menu
multi-step ramp is selected.
Display Parameter
For Ramp Events and
Soak Events to be
Recycle Number
employed, A larm 1 or
(Recipe Executions)
A larm 2 must be set for
Power Fail Resume
event usage
in
the A larm Menu.
Ramp Times 1-8
Ramp Events 1-8
Soak Levels 1-8
Soak Times 1-8
Soak Events 1-8
Supervisor Menu
Display Parameter
Output 1
Failsafe State
Output 2
Failsafe State
Loop Break Time
Highest Reading
Lowest Reading
Load Default
The Failsafe State is
Parameters
only enforced when a
Choosing "Yes" to Load Default Parameters resets all menu
problem is detected
parameters to factory settings.
with the process input.
It is not reliably
enforceable in
instances of internal
circuitry failure such as
EEPROM problems.
Output % High Limits
are ignored when the
unit enters a Failsafe
State.
Selection
0-99,
Off
On
0-9999 mins.
Alarm 1 On
Alarm 1 Off
Alarm 2 On
Alarm 2 Off
Disabled
Display Units, FS
0-9999 mins.
Alarm 1 On
Alarm 1 Off
Alarm 2 On
Alarm 2 Off
Disabled
Selection
0 to 100%
of output
0 to 100%
of output
Off, 4-9600 sec
n/a
n/a
28
Calibration Menu
Toggles with the temperature value that should be input to
perform the low calibration operation.
The low calibration operation is triggered by pressing the
up arrow key.
Toggles with the temperature value that should be input to
perform the high calibration operation.
The high calibration operation is triggered by pressing the
up arrow key.
Options Menu
Display Parameter
Installed Card
29
Selection
Serial Communications
Serial Communications
with Switch Input
Remote Analog Setpoint
Auxiliary Output
Alarm
Switch Input with Alarm
Table of
Contents
Previous
Page
Next
Page
1
...
16
17
18
19
20
21
22
23
Advertisement
Table of Contents
Related Manuals for Omega CN8200 Series
Temperature Controller Omega CNi8 Manual
I-series temperature & process controller manual (72 pages)
Temperature Controller Omega C9000A SERIES User Manual
Autotune temperature controller (92 pages)
Temperature Controller Omega CN63100 Series User Manual
1/16 din temperature/process controllers (92 pages)
Temperature Controller Omega CN1001-RTD User Manual
(64 pages)
Temperature Controller Omega CN710 Instruction Sheet
(2 pages)
Temperature Controller Omega CN76000 Manual
(54 pages)
Temperature Controller Omega CN1000-RTD Quick Start
Temperature controller with time proportional control (2 pages)
Temperature Controller Omega CN616TC1 User Manual
Cn616 series 1/4 din economical 6-zone pid temperature controllers (28 pages)
Temperature Controller Omega FUZZY LOGIC CN4800 Manual
(102 pages)
Temperature Controller Omega i Series User Manual
Temperature & process monitor, temperature & process limit alarm (57 pages)
Temperature Controller Omega CN9000A Series User Manual
(92 pages)
Temperature Controller Omega CYD211 User Manual
Single input temperature monitor (76 pages)
Temperature Controller Omega CN4000 Series User Manual
(13 pages)
Temperature Controller Omega CND3 Series User Manual
(28 pages)
Temperature Controller Omega OS212-MT User Manual
Os212 series, compact non-contact temperature sensor (35 pages)
Temperature Controller Omega OS130A Series User Manual
Non-contact infrared temperature sensor/transmitter (16 pages)
Related Content for Omega CN8200 Series
i Series Menu Configuration
Omega i Series
CN76000 Menu Selections
Omega CN76000
CNi8 Menu Configuration
Omega CNi8
Table of Contents
Print
Rename the bookmark
Delete bookmark?
Delete from my manuals?
Login
Sign In
OR
Sign in with Facebook
Sign in with Google
Upload manual
Upload from disk
Upload from URL