Service Mode - Roland SOLJET Pro III XC-540 Service Notes

4-2 SERVICE MODE

[ ], [ ], [ ] + POWER ON
SERVICE MENU PRINT MENU
PRINT MENU HEAD RANK
PRINT MENU
HEAD ADJUST
MENU
[ MENU ] key
SERVICE MENU
HEAD RANK
HEAD 1
HEAD RANK
HEAD 6
HEAD ADJUST
BIAS
HEAD ADJUST
VERTICAL
HEAD ADJUST
HORIZONTAL
HEAD ADJUST
BI-DIR.DEFAULT
HEAD ADJUST
STANDARD HEAD
This menu is used for adjusting Head Alignment. Refer to [4-4 HEAD ALIGNMENT].
4-2
HEAD RANK 1
This menu is used for entering the HEAD RANK for each HEAD
1234567 (1/5) with 35 digit number and alphabet. The digits can be changed
with [left] and [right] keys and parameters can be changed with
[up] and [down] keys. The digit being changed is marked with
an under bar. Press the [ENTER] key to save the settings.
HEAD RANK 6
Warning sound goes off when the calculation for verification,
CHECK SUM, is not correct, in order to avoid input error.
1234567 (1/5)
BIAS
PERFORMING
TEST PRINT
Feeds media for visual check of the test pattern, by pressing [up] or [down]
keys while in [TEST PRINT] menu. Also by pressing [up] or [down] keys again
after feeding, media returns to the original position.
BIAS
--- VIEW ---
VERTICAL
PERFORMING
TEST PRINT
Feeds media for visual check of the test pattern, by pressing [up] or [down]
keys while in [TEST PRINT] menu. Also by pressing [up] or [down] keys again
after feeding, media returns to the original position.
VERTICAL
--- VIEW ---
HORIZONTAL
PERFORMING
TEST PRINT
TEST PRINT
HORIZONTAL H1
DT1, Low 2
HORIZONTAL H1
DT3, Low 2
HORIZONTAL H1
DT1, High 2
HORIZONTAL
H1
DT3, High 2
Cursor can be moved with [left] and [right] keys, and value can be selected with [up] and [down]
keys. The value being selected is marked with an under bar. It returns to the former menu by
pressing [left] key when the cursor is on the head of the left end. It starts with H2 when H1 is
defined as the standard head.
Default: 0 Range: -30 to +30dot (changeable by 0.5dot) 0.5dot is indicated as 1/2.
BI-DIR.DEFAULT
TEST PRINT
TEST PRINT
123456
Cursor can be moved with [left] and [right] keys, and the heads can
be turned ON/OFF with [up] and [down] keys. Press [ENTER] key to
start the test print of the selected heads. It returns to the former menu
by pressing [left] key when the cursor is on the head 1.
BI-DIR.DEFAULT H1 H2
DT1, Low 2
BI-DIR.DEFAULT H1 H2
DT3, Low
2
BI-DIR.DEFAULT H1 H2
DT1, High
2
BI-DIR.DEFAULT H1 H2
DT3, High 2
Cursor can be moved with [left] and [right] keys, and value can be selected with [up] and [down]
keys. The value being selected is marked with an under bar. It returns to the former menu by
pressing [left] key when the cursor is on the head of the left end.
Default: It can be changed starting from the standard value (15) with [up] and [down] keys.
Range: 0 to +60dot (changeable by 0.5dot which is indicated as 1/2.
STANDARD HEAD
3 > 3
TEST PRINT
TEST PRINT
H2 H3 H5 H6
1 3 2 1
H2 H3 H5 H6
1 3 2 1
H2 H3 H5 H6
1 3 2 1
H2 H3 H5 H6
1 3 2 1
PERFORMING
TEST PRINT
H3 H4 H5 H6
1 3 2 1 3
H3 H4 H5 H6
1 3 2 1 3
H3 H4 H5 H6
1 3 2 1 3
H3 H4 H5 H6
1 3 2 1 3
This menu is hidden normally.
It appears when Base Head Menu is enabled
on Bit6 of PAGE2 in SYSTEM SWITCH menu.