Table of Contents
Advertisement
To Bypass Zones:
∗
Enter [
][1] - the "Bypass" light will start flashing.
Enter [zone number to be bypassed]; the zone light will come
ON to indicate that the zone is bypassed. To remove a
bypass, enter the zone number and the zone light will go OFF.
Continue entering the zone numbers for the zones you want
bypassed. Press [#] to return to Ready.
NOTE: Any zone defined as 24 Hour Bell, 24 Hour Bell/
Buzzer, or 24 Hour Buzzer cannot be bypassed while that
zone is violated. To bypass a 24 hour zone, the zone must be
physically restored.
To Recall Bypassed Zones:
∗
Enter [
][1][9]
This command will recall the last zone or group of zones that
were bypassed. If the same group of zones are bypassed
regularly, the bypass recall feature can be used instead of
bypassing the zones individually.
Bypass Disable:
The PC1510 can be programmed by the installer to prevent
certain zones from being bypassed by the user. Lights for
these zones will not come ON in response to the bypass
command. See the Zone Bypass Mask instruction in the
installer programming section [16].
Trouble Conditions
∗ ∗ ∗ ∗ ∗
[
]+[2]
The PC1510 continuously monitors a number of trouble
conditions. If one of these conditions occurs, the keypad
"Trouble" light will come ON and the buzzer will sound two
short beeps every 10 seconds. To silence the buzzer, press
the [#] key. The buzzer will stop but the "Trouble" light will
remain ON until the trouble condition is cleared. See the
Programming Guide section [10], Maintenance Alarms &
Restorals for a list of those zones that can be transmitted to
the monitoring station.
To view the trouble condition, press [
1. Low Battery. If the battery voltage is low, the battery is
disconnected or the battery fuse is blown, a trouble will be
displayed and can be reported.
2. AC Failure. On loss of AC power, the "Trouble" light will
come ON immediately, but the keypad buzzer will not
sound. The keypad buzzer will sound if AC power remains
off and the battery reaches a low voltage. The delay
before transmitting AC Fail can be programmed from 1 to
99 minutes. See Programming Section [17].
3. Fuse Failure - Bell / Siren or AUX Output. A trouble is
displayed if the Bell / Siren fuse is open. If the AUX output
fuse fails, it will not be displayed but will be transmitted if
programmed to do so.
4. Unsuccessful Communication Attempt If the digital
communicator is unsuccessful at communicating with the
monitoring station after 8 attempts at each phone number
that is tried, a trouble is generated. See section [15],
Communication Variables.
communication is successful, the trouble is cleared. The
trouble can also be cleared by pressing the [#] key to exit
from the trouble view mode.
∗
][2].
If a later attempt at
5. Fire Alarm Circuit Trouble An open circuit on the zone
programmed as a fire loop will initiate a trouble. See Zone
Definitions section [11] for fire loop zone assignment.
6. Loss of Time on System Clock When the PC1510 is
powered up or reset, the internal time of day clock needs
to be reset to the correct time. The trouble is cleared after
entering the trouble view mode then pressing [#] to exit.
The trouble will also be cleared on any attempt to set the
∗
time of day. See [
][6] User Function Command for
setting the clock. Press [#] to return to Ready. NOTE: A
trouble will not be generated if both the test transmission
and Auto-Arm times are not programmed with valid times.
NOTE: If [9] is pressed while in the trouble display mode, the
most recent trouble will be displayed on the zone lights. This
trouble memory is most useful as a diagnostic tool when
installing and servicing the PC1510. Press [#] to return to
"Ready".
Alarm Memory
∗ ∗ ∗ ∗ ∗
[
]+[3]
Alarms caused during the previous armed period are stored
in memory. To view these alarms, press [
"Memory" light will flash and the alarm(s) will be displayed on
the flashing zone lights.
In addition to the last alarm memory, there are two history
levels. After entering the memory mode, pressing any key [0]
to [9] will display the two other levels of alarm history. Each
time a key is pressed, the keypad will beep 1, 2 or 3 times to
indicate which level of history is being viewed.
When the panel is armed, and if there is an alarm in the 1st
level, the 1st level is cleared and the contents moved to the
2nd level. The 2nd level contents are moved to the 3rd level
and the 3rd level contents are discarded. The "Memory" light
will be ON only if there was an alarm during the previous
armed period. Press [#] to return to Ready.
Downloading Callup Command
∗ ∗ ∗ ∗ ∗
[
]+[4]
∗
The [
][4] command is used to initiate a call to the
downloading computer so that the panel can be accessed by
the computer. This command must be enabled in section
[14], 3rd system option code, zone light 2. Sections [26], [27]
and [28] must be programmed with the downloading
computer's telephone number, the downloading access
code and the panel identification code. NOTE: The [
command can be programmed to require a access code
∗
(e.g. [
][4][4-digit access code]) if section [14] light 4 is
turned ON.
User Programming Commands
∗ ∗ ∗ ∗ ∗
[
]+[5]
∗
The [
][5] programming command allows the user to program
access codes 2 through 6. The 1st access code is the Master
Code, which the installer may choose not to allow the user to
program (section [13] light 2). The factory default for the
Master Code is "1234". The 6th code may be changed from
a regular code into a "one-time" use or "Maid's Code". See
section [13] light 5.
NOTE: The One-time Use code is only cleared when it is used
to arm. If the Quick-Arm command [
"one-time" code will not be erased.
∗
] then [3]. The
∗
][4]
∗
][0] is used to arm, the
7
Advertisement
Table of Contents
