Advertisement
Quick Links
ViZion DR +
Wireless Install Guide
1. Open the DR panel box.
2. Put aside the three cables from the top layer of Styrofoam for storage. These cables are only required
for potential troubleshooting scenarios.
3. The panel is shipped in an antistatic bag. Remove the bag from the box.
VZ0001HTG201507-2.6
Customer Support
ViZion DR + Install Guide v2.6
HCITsupport@konicaminolta.com
1.800.366.5343 –
1
Opal UAI 2.3.x.x
Advertisement
Related Manuals for Konica Minolta ViZion DR +
Summary of Contents for Konica Minolta ViZion DR +
- Page 1 ViZion DR + Install Guide v2.6 ViZion DR + Opal UAI 2.3.x.x Wireless Install Guide 1. Open the DR panel box. 2. Put aside the three cables from the top layer of Styrofoam for storage. These cables are only required for potential troubleshooting scenarios.
- Page 2 ViZion DR + Install Guide v2.6 Opal UAI 2.3.x.x 4. Remove the panel from the antistatic bag. 5. Remove the battery charger from the box. Under the battery charger are two (2) external power supplies. One (1) is to be used for the battery charger, and the other can be stored. 6.
- Page 3 ViZion DR + Install Guide v2.6 Opal UAI 2.3.x.x 7. After batteries are charged, insert battery into panel. Turn panel over with battery compartment facing up. a. Slide battery into the Panel at a slight angle mating the charging connector with the battery connector.
- Page 4 ViZion DR + Install Guide v2.6 Opal UAI 2.3.x.x 9. Locate the power buttons on the edge of the panel. a. Press and hold the power button for up to 10 seconds or until the lights turn on. A. Battery status (green - battery is charged, orange – replace battery soon) B.
- Page 5 ViZion DR + Install Guide v2.6 Opal UAI 2.3.x.x AP Setup 1. Unbox Asus Access point (model may vary based on availability). ------------- 2 ------------- 1A-1D: Wifi Antennas Gigabit Lan Ports Reset Button (Restores Access Point to Factory Defaults) 4: Power Button AC adapter Plug 2.
-
Page 6: Monitor Setup
ViZion DR + Install Guide v2.6 Opal UAI 2.3.x.x 6. Access point is configured from the factory with the following settings: 2.4ghz radio – Disabled 5 GHz radio - Enabled IP address 192.168.8.50 for the router username: admin (default username: admin) password: 12345678 (default password: admin) SSID : ViZionDREXAP password : 12345678 Note: DHCP is disabled and the AP will not assign addresses to network devices. - Page 7 ViZion DR + Install Guide v2.6 Opal UAI 2.3.x.x 2. Attach platform to base. 3. Attach Base to Monitor. 4. Cover wall mount screws with provided cover. 5. Insert power cable into monitor and plug power cable into wall outlet. 6.
- Page 8 ViZion DR + Install Guide v2.6 Opal UAI 2.3.x.x Back of ELO Monitor 1: AC Power cable 2: USB cable (A to B standard) 3: VGA Cable HCITsupport@konicaminolta.com Customer Support 1.800.366.5343 – VZ0001HTG201507-2.6...
- Page 9 ViZion DR + Install Guide v2.6 Opal UAI 2.3.x.x PC Setup 1. Open PC Box. 2. Remove Key Board and Accessories box. 3. Remove PC and place PC in X-ray work area. 4. Plug Keyboard into PC USB port. 5. Plug Mouse into PC USB port. 6.
- Page 10 ViZion DR + Install Guide v2.6 Opal UAI 2.3.x.x PC Wiring guide made simple Connect the onboard network card to the office’s local area network. Connect the mouse and Keyboard to any available USB port. Connect the monitor to the PC VGA port Note for ELO Monitors attach the USB cable to an open...
- Page 11 ViZion DR + Install Guide v2.6 Opal UAI 2.3.x.x ELO Touchscreen software install and Calibration 1. Click the desktop icon. 2. At the first prompt, click OK. 3. At the next prompt, click Unzip. Customer Support 1.800.366.5343 – HCITsupport@konicaminolta.com VZ0001HTG201507-2.6...
- Page 12 ViZion DR + Install Guide v2.6 Opal UAI 2.3.x.x 4. At the next prompt, cick OK. 5. At the Touch Screen setup, click Next. Customer Support 1.800.366.5343 – HCITsupport@konicaminolta.com VZ0001HTG201507-2.6...
- Page 13 ViZion DR + Install Guide v2.6 Opal UAI 2.3.x.x 6. Check the box next to “Install USB Touchscreen Drivers.” 7. At the next prompt, click Yes. Customer Support 1.800.366.5343 – HCITsupport@konicaminolta.com VZ0001HTG201507-2.6...
- Page 14 ViZion DR + Install Guide v2.6 Opal UAI 2.3.x.x 8. When prompted, click Finish. 9. Plug the USB cable into the back of the pc. Wait for one minute for windows to complete driver installation. Customer Support 1.800.366.5343 – HCITsupport@konicaminolta.com VZ0001HTG201507-2.6...
- Page 15 ViZion DR + Install Guide v2.6 Opal UAI 2.3.x.x 10. Click the ELO icon in the system tray. 11. Click the Align option. Customer Support 1.800.366.5343 – HCITsupport@konicaminolta.com VZ0001HTG201507-2.6...
- Page 16 ViZion DR + Install Guide v2.6 Opal UAI 2.3.x.x 12. Touch the bull’s eye symbol on the screen. 13. Touch each bull’s eye as they display on the screen. Customer Support 1.800.366.5343 – HCITsupport@konicaminolta.com VZ0001HTG201507-2.6...
- Page 17 ViZion DR + Install Guide v2.6 Opal UAI 2.3.x.x 14. Touch different areas on the screen. If the mouse follows the spots you touch, then touch the green check symbol on the screen. Installation of the ELO touch screen monitor is complete. Customer Support 1.800.366.5343 –...