Advertisement
Light function off
•
The device switches off, the motion detector no longer
responds
•
Automatic change to auto mode after 8 hours
•
Exiting the function with any other function command
Entering and calling up lighting scenarios
L Automatic change to auto mode after 8 hours
L Exiting the function with any other function command
In the app → parameters → select value for lighting
†
†
scenario 1 (default 33%), or lighting scenario 2 (default
66%), and send; or
set the desired value via dimming with theSenda B or
†
†
theSenda S
Hold down the button for lighting scenarios
†
†
▻ Detector flashes 2 x and lighting scenario is saved
Calling up lighting scenario
With theSenda B, press the button for lighting scenario
†
†
1 x briefly
▻ Lighting scenario is active for 8 hours
Press button A, to prematurely finish the function
†
†
Holiday mode (presence simulation)
L The holiday mode always has a time delay of 2 min. and
changes the setpoint. If the mode is exited via the button
or command A (Auto), the desired time delay has to be set
again.
In the app → control commands → select presence simu-
†
†
lation, and send
or press the "holiday mode" button with theSenda B or
†
†
theSenda S
Manual operation
The lighting can be switched on manually via a circuit breaker
button.
L A circuit breaker button must be connected.
N
L
E
N
L
Press the circuit breaker button briefly (max. 1.5 s).
†
†
▻ The lighting will come on for the set time.
Press the circuit breaker button 2 x briefly (within 1.5 s).
†
†
▻ The lighting remains switched on for 8 hours (perma-
nent light).
L
N
In order to switch off the lighting, press the circuit breaker
†
†
button 1 x briefly (max. 1.5 s).
▻ The detector switches off after the set time delay.
N
L
L If the circuit breaker button is pressed longer than 2 s, the
detector restarts (warm-up phase).
10. Settings with remote controls
L You can enter the settings with the remote controls the-
Senda S, theSenda P, and theSenda B.
L All settings can be quit by pressing button A.
Settings using theSenda P (9070910)
The following parameters or functions can be set with
theSenda P:
31
30
26
25
24
23
22
21
20
18
17
16
1
Test
Test mode, ends after 10 min
2
Auto
return to Automatic mode
6
On
Switch on light*
7
Range +
Increase sensitivity
8
15 lux
Brightness setpoint value 15 lux
9
10 lux
Brightness setpoint value 10 lux
10
Lux On
Deactivation of brightness measurement
11
800 lux
Brightness setpoint value 800 lux
12
60 s
Lighting time delay 60 s
13
30 s
Lighting time delay 30 s
14
max. Time
max. lighting time delay, 20 min
15
20 min
Lighting time delay 20 min
16
10 min
Lighting time delay 10 min
17
2 min
Lighting time delay 2 min
18
min. Time
min. lighting time delay, 10 s
20
500 lux
Brightness setpoint value 500 lux
21
300 lux
Brightness setpoint value 300 lux
22
5 lux
Brightness setpoint value 5 lux
23
min. Lux
min. brightness setpoint value, 1 lux
24
Range –
Reduce sensitivity
25
Teach-in
Teaching in the brightness setpoint value
26
Off
Switch off light*
30
Reset
Restart of the detector
31
D mode
Dimming function (motion detector deactivated)
* active for 8 hours
1
2
6
7
8
9
10
11
12
13
14
15
5
Advertisement
