Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Bosch MIC Series
Summary of Contents for Bosch MIC Series
- Page 1 Confi guration of MIC IP 7000 HD – VIDEOJET decoder 3000 – for integration with analog CCTV | 1/18 Confi guring MIC IP 7000 HD with VIDEOJET decoder systems 3000 for integration with analog CCTV Tech-note Bosch Security Systems Version 1.3 | September 2015...
-
Page 2: Table Of Contents
Hardware interface between VIDEOJET decoder 3000 and analog controller 4.5.1 Integration with Bosch LTC 5136 standalone PTZ controller: 4.5.2 Integration with Bosch Allegiant matrix switcher and VIDEOJET decoder 3000 4.5.3 Integration with Pelco matrix switcher and VIDEOJET decoder 3000 4.5.4 Integration with SYNECTICS EX250 system and VIDEOJET decoder 3000 Version 1.3 | September 2015... -
Page 3: References
LTC 5136: Standalone PTZ controller http://resource.boschsecurity.com/documents/LTC_5136_User_Guide___Instruction_Book_ enUS_11969409035.pdf MIC BP3: Biphase to RS 485 converter http://resource.boschsecurity.com/documents/installation_guide_enus_2306909579.pdf Intelligent Dynamic Noise Reduction (IDNR) http://www.boschsecurity.com/HDSecurity/Default.aspx?language=en&tab=cbit&content=idnr Content Based Imaging Technology (CBIT) http://www.boschsecurity.com/HDSecurity/Default.aspx?language=en&tab=cbit starlight technology http://www.boschsecurity.com/HDSecurity/Default.aspx?language=en&tab=starlight Intelligent Video Analysis (IVA) http://www.boschsecurity.com/HDSecurity/Default.aspx?language=en&tab=inteligent-video-analysis Bosch Security Systems Version 1.3 | September 2015... -
Page 4: Product Selection Guide
4/18 | Configuration of MIC IP 7000 HD – VIDEOJET decoder 3000 – for integration with analog CCTV Product selection guide Bosch MIC family provides several options to satisfy diverse installation scenarios and applications. The decision matrix below helps you select between the analog, IP or Hybrid solution depending on the type of infrastructure and future upgrades required at the site. -
Page 5: Introduction
MIC IP 7000 HD cameras in existing analog infrastructure without investing in an entire system upgrade. This tech note explains how to integrate the Bosch MIC IP 7000 HD camera series into any existing analog CCTV system using the Bosch VIDEOJET decoder 3000. The most common integration scenarios are listed below: •... -
Page 6: Single Camera Installlation
Figure 1: MIC IP 7000 HD direct decoder connection with no local recording. Figure 2: MIC IP 7000 HD direct decoder connection with local recording in DVR. For SW configuration and details about interface ports, please see Section 4.0. Version 1.3 | September 2015 Bosch Security Systems... -
Page 7: Multiple Camera Installation With Matrix Switchers Or Dvrs
Bosch OSRD • Forward Vision Figure 3: MIC IP 7000 HD connectivity with Bosch Allegiant Matrix switcher. Figure 4: MIC IP 7000 HD with generic matrix switcher using Pelco or Forward Vision protocol. Bosch Security Systems Version 1.3 | September 2015... -
Page 8: Available Functions In Ip And Analog Configurations
8/18 | Confi guration of MIC IP 7000 HD – VIDEOJET decoder 3000 – for integration with analog CCTV Available functions in IP and analog confi gurations Version 1.3 | September 2015 Bosch Security Systems... -
Page 9: Device Configuration
Device Confi guration Install protocol eLicense Using web browser or Bosch Confi guration Manager, follow instructions in camera operating manual to install and activate the eLicense needed to support serial protocol functionality. Hardware interface between MIC IP 7000 HD and VIDEOJET decoder 3000 The only interface necessary between a MIC IP 7000 HD and a VIDEOJET decoder 3000 is network connectivity for video decoding. - Page 10 10/18 | Configuration of MIC IP 7000 HD – VIDEOJET decoder 3000 – for integration with analog CCTV Figure 6: Direct interface between MIC IP interfaces to VIDEOJET decoder 3000 Figure 7: MIC IP 7000 HD and VIDEOJET decoder 3000 interface. Version 1.3 | September 2015 Bosch Security Systems...
-
Page 11: Mic Ip 7000 Hd Configuration
CCTV system. These are described below. A temporary network connection to access the camera’s web browser or use of the Bosch Configu- ration Manager software is required in order to make these changes. Please refer to the MIC Operating manual which can be found at the link in section 1 for complete information on how to connect the MIC camera up to an IP network. -
Page 12: Mic Ip 7000 Hd: Fastaddress
Important note: Whenever you change the FastAddress you have to reboot the camera to activate the new FastAddress setting! Either power camera off/on, or use Reboot button in Installer Menu of web browser Version 1.3 | September 2015 Bosch Security Systems... -
Page 13: Videojet Decoder 3000 Configuration
Point the web browser to the camera IP address (when the VIDEOJET is reset to factory defaults, the IP address of the decoder is 192.168.0.1). Go to the SETTINGS page to start the configuring the unit. Figure 10: Decoder SETTINGS menu. Bosch Security Systems Version 1.3 | September 2015... - Page 14 Click the Set button. Figure 11: Decoder Profile configuration. In the Interfaces -> COM1 menu, select the settings featured in the image below. Click the Set button. Figure 12: COM1 port configuration menu. Version 1.3 | September 2015 Bosch Security Systems...
- Page 15 7000 HD camera. The camera URL will appear in the URL field. Select: Video input: 1 Stream: H264 2 Decoder: 1 Click single stream button Click connect Figure 14: Video source list under the CONNECTIONS menu. Bosch Security Systems Version 1.3 | September 2015...
-
Page 16: Hardware Interface Between Videojet Decoder 3000 And Analog Controller
As shown below, the decoder supports RS 232, RS 422, and RS 485 transmission standards and accepts telemetry control using Bosch OSRD, Pelco P/D and Forward Vision protocols. Figure 15: Interface ports for integration with monitoring and control equipment. -
Page 17: Integration With Bosch Ltc 5136 Standalone Ptz Controller
Configuration of MIC IP 7000 HD – VIDEOJET decoder 3000 – for integration with analog CCTV | 17/18 4.5.1 Integration with Bosch LTC 5136 standalone PTZ controller: The Bosch LTC 5136 can control a single camera using the RS-232 output. It also can control a maxi-mum of 16 PTZ cameras using the Biphase output. Using RS-232 control Using the LTC 5136 with RS-232 control requires an additional LTC 8557 connection kit. -
Page 18: Integration With Bosch Allegiant Matrix Switcher And Videojet Decoder 3000
Integration with Bosch Allegiant matrix switcher and VIDEOJET decoder 3000: The Bosch Allegiant series offers an extensive portfolio of analog matrix switchers. Depending on the selected matrix switcher family, there are direct Biphase ports on the main switching bay or available through additional signal distribution. -
Page 19: Integration With Synectics Ex250 System And Videojet Decoder 3000
HD family can be integrated into an existing EX250 (or equivalent system) using the Forward Vision protocol. Figure 21: Interface between SYNECTICS controller and VIDEOJET decoder 3000. For specific menu option for SYNECTICS products, please refer to the manufacturer’s installation manuals. Bosch Security Systems Version 1.3 | September 2015... - Page 20 20/18 | Confi guration of MIC IP 7000 HD – VIDEOJET decoder 3000 – for integration with analog CCTV Bosch Security Systems To fi nd out more about our IP video solutions and technologies go to www.boschsecurity.com/hdsecurity © Bosch Security Systems, 2015 Modifi cations reserved VS-EH-en-06_F01U521082_01 www.facebook.com/BoschSecurity www.twitter.com/BoschSecurityEU www.youtube.com/BoschSecurity...