Peg-Perego Si Instructions For Use Manual page 13

following parts: 2 swivel/lockable front wheels, 2
rear wheels, basket, cup holder, hood, rain canopy,
2 shoulder straps and 1 leg divider, 2 car seat strap
adaptors.
INSTRUCTIONS
1• OPENING: To open the stroller, press the lever on the
left hand side (fig_a), grip the handles, pull upwards
and at the same time lift the stroller (fig_b). Check that
the stroller is properly opened by making sure that the
side clips are correctly fastened (fig_c).
2• If the straps are not fasten correctly, press onto the
seat (fig_a) until it clicks into place.
Then push down into PUSH (fig. b) with your foot and
lift the front bar by one position (section 5b).
3• BASKET: To fit the basket, pull the loops over rear
hooks A and B and front hook C (fig_a).
CUP HOLDER: It can only be fitted to the right hand
side of the stroller, using the clip which is already
present on the chassis. To fit the cup holder, push until
it clicks into place (fig_b).
4• HANDLE ADJUSTMENT: The handles can be set at
3 different heights. To move them into the required
position, press the button and simultaneously pull the
handle upwards. To lower them, press the button and
push the handle down (fig_a).
BRAKE: To set the brake on the stroller, lower the lever
on the rear wheel unit with your foot. To release the
brake, lift the lever (fig_b). When stationary, always
apply the brake.
5• SWIVEL WHEELS: the wheels are already fixed into the
stroller.
In order to make the wheels swivel, the lever (arrow 1)
must be lowered. To secure the wheels, move the lever
to the opposite direction (arrow 2). The rear wheels
are fixed.
FRONT BAR: is already fixed into the stroller. It can be
adjusted to 2 positions by pressing simultaneously the
side buttons on both sides (fig_b).
6• HOOD: To fit the hood, click the fasteners onto the
appropriate points and button down the hood on the
rear of the stroller's backrest (fig_a).
The hood can be set in 3 different positions (fig_b) by
simply pulling it forwards or backwards.
The section of netting can be pulled out from the hood
to protect the child from the sun (fig_c) and easily
replaced back inside when it is no longer needed.
7• COVER: in order to use the cover correctly (fig. a),
fasten the buttons in the inner part of the stroller (fig.
1) and lay it beneath the seat covering the footrest,
then fasten the buttons (fig. 2).
RAIN CANOPY: To fit the rain canopy, slip it onto the
stroller (fig_b), button it down on the sides of the
hood (fig_1) and attach the elastic loops, taking in the
chassis in the lower part of the stroller (fig_2).
8• 5-POINT SAFETY HARNESS: to fasten, insert the two
buckles of the waist strap (with attached shoulder
straps, arrow a) into the leg divider strap until they
click into place (arrow b). To unfasten, push the round
button placed in center of the buckle upwards (arrow_
c) and pull the waist strap outwards (arrow d).
9• To tighten the waist strap, pull on both sides in the
direction of the arrow (Fig. a). To loosen it do the
opposite. The waist strap can be tightened as far as the
safety lock (Fig. b).
SI_EU_FI000904I101.indd 13
1 0• It is possible to set the safety harness at 2 different
heights, depending on how tall the child is. When the
child is bigger, it is necessary to switch to the higher
position (number 2).
1 1• To adjust the height of the safety harnesses, release
the two buckles on the rear of the backrest.
Pull the shoulder straps towards you (arrow a) until the
buckles are released and insert them in the backrest
loops (arrow b). Remove the shoulder straps from the
sack (arrow c) and insert them in the most appropriate
buckle (arrow d), then reattach the two buckles
behind the backrest (arrow e). The buckles are securely
attached when a click is heard (fig f).
1 2• LEG REST ADJUSTMENT: The leg rest can be set in 2
different positions. To lower the leg rest, pull the two
side levers downwards and at the same time lower the
leg rest. To raise the leg rest, push it upwards until it
clicks into position.
BACKREST ADJUSTMENT: The backrest can be set in 3
positions: To lower the backrest, lift the levers on both
sides at the same time and lower it, locking it in the
position required. To lift the backrest, push it upwards.
1 3• FOLDING UP: in order to fold up the stroller, it is
recommended to first lower the front bar to the lowest
position.
Lower the fold release lever (fig_a) until it clicks" then
pull the central handlebar (fig_b). Make sure the
stroller is folded correctly. The small lever on the left
side must be fastened correctly. Once the stroller is
folded, it shall stand by itself (fig_c).
1 4• TRANSPORT: The stroller can be moved with ease (with
the front wheels fixed) using the central handle (fig_a).
It can also be carried using the side handle (fig_b).
1 5• REMOVABLE COVERS: To remove the cover of the
stroller:
Release the two buckles on the rear of the backrest
(fig_a).
Release the two buttons on the seat (fig_b).
Pull the buckle of the crotch strap out from
underneath (fig_c).
Release the buttons from the side of the sack (fig_d).
1 6• Pull the sack off the footrest (fig_e).
To remove the safety harness, release the screws on
both sides, using a screwdriver and pliers to hold the
nut still (fig_f ).
Pull the sack upwards (fig_g).
ATTACHING PRIMO VIAGGIO TRI-FIX,
PRIMO VIAGGIO TRI-FIX or PRIMO
VIAGGIO TRI-FIX ES CAR SEATS
You must first set the brakes on the stroller.
Lock the car seat onto the stroller without the baby.
The car seat must be fastened facing the mother at
all times.
If necessary, take off the stroller hood since it is
already fitted on the car seat.
Position the backrest of the stroller into the 2nd
central position (section 12).
Position the car seat handlebar into transport
position so that the straps can be easily fastened.
1 7 Push the button beneath the armrest and extend
•
the front bar, then simultaneously pull it out from
- 13 -
16-07-2009 8:57:46