Settings For The Entire Unit; Making The Power Automatically Turn Off After A Time (Auto Off ); Returning To The Factory Settings; "Factory Reset - Roland JUPITER-Xm Owner's Manual

Settings for the Entire Unit

Making the Power Automatically Turn Off
After a Time
(Auto Off )
1.
Press the [MENU] button.
2.
Use the [1] knob to select
[ENTER] button.
You can also make this selection by using the
instead of the [1] knob.
3.
Use the [1] knob to select
change the setting.
If you don't want the unit to turn off automatically, choose
setting.
Parameter Value
[1] knob [2] knob
OFF, 30 [min], 240 [min]
Auto Off
4.
To save the setting, press the
The save page appears.
5.
To execute, press the [ENTER]
If you decide to cancel, press the

Returning to the Factory Settings

(Factory Reset)
Here's how the settings that you edited and saved on the JUPITER-Xm
can be returned to their factory-set condition.
* When you execute this operation, all saved settings including the sound
parameters will be lost.
* If you will later need the current settings, be sure to use the backup
function (p. 18) to save the current settings before you restore the
factory settings.
1.
Press the [MENU] button.
2.
Use the [1] knob to select
[ENTER] button.
You can also make this selection by using the
instead of the [1] knob.
3.
Use the [1] knob to select
the [ENTER] button.
A confirmation message appears.
If you decide to cancel, press the
4.
To execute, use the [2] knob
the [ENTER] button.
The display indicates "Completed. Turn off power."
5.
Turn the power of the JUPITER-Xm off and then on again.
* Never turn off the power or disconnect the USB flash drive during a
process, such as while the "Executing..."
"SYSTEM," and then press the
PAGE [ ] [ ] buttons
"Auto Off" and use the [2] knob
"OFF"
[WRITE] button.
button.
[EXIT] button.
"UTILITY," and then press the
PAGE [ ] [ ] buttons

"FACTORY RESET,"

and then press
[EXIT] button.
to select "OK," and then press
display is shown.
Saving the System Settings
1.
Press the [MENU] button.
2.
Use the [1] knob to select
[ENTER] button.
You can also make this selection by using the
instead of the [1] knob.
3.
Use the [1] knob to select the parameter and use the
knob to change the setting.
to
Saving the System Settings
1.
Press the [WRITE] button.
The SYSTEM WRITE screen appears.
If the WRITE MENU screen appears, use the
select "SYSTEM," and then press the
2.
To execute, press the
If you decide to cancel, press the
System parameter list
Parameter Value
[1] knob [2] knob
GENERAL
415.3–466.2 [Hz]
MasterTune
-24–24
MasKeyShift
OFF, ON
ScaleTuneSw
0–127
USB In Lev
0–127
USB Out Lev
0–127
AuxIn/BT InLev
-12–0–+12 [dB]
LineOut Gain
OFF, ON, AUTO
Speaker Sw
-12–0 [dB]
SPOut Gain
OFF, 30 [min],
Auto Off
240 [min]
OFF, ON, FAST
Aging
Aging Init Temp REAL, 0–60 [ C]
0–31
LED On Bright
0–30
LED OffBright
1–10
LCD Contrast
(SYSTEM)
"SYSTEM," and then press the
PAGE [ ] [ ] buttons
(System Write)
[1] knob or [2] knob
[ENTER] button.
[ENTER] button.
[EXIT] button.
Explanation
Adjusts the overall tuning.
The displayed value is the frequency of the
A4 key (middle A).
Shifts the JUPITER-Xm's overall pitch range
in semitone steps.
Specifies whether the scene's SCALE TUNE
setting is enabled (ON) or disabled (OFF).
Adjusts the audio input level of the USB
COMPUTER port.
Adjusts the audio output level to the USB
COMPUTER port.
Adjusts the input level of the AUX IN jack.
Adjusts the output gain of OUTPUT/
PHONES.
Specifies whether sound is output from
the speakers. The AUTO setting operates
as "OFF" when headphones are connected
and as "ON" when headphones are not
connected.
Adjusts the output gain of the speakers.
Specifies whether the unit will turn off
automatically after a certain time has
elapsed.
If you don't want the unit to turn off
automatically, choose "OFF" setting.
Simulates the pitch instability of an analog
synthesizer.
For details, refer to "Reference Manual"
(PDF).
For details, refer to "Reference Manual"
(PDF).
Adjusts the brightness when the LEDs are
lit.
When the JUPITER-Xm is operating with
the AC adaptor, you can make the LEDs
remain dimly lit when off instead of going
completely dark.
This setting adjusts the LED brightness
when off.
Adjusts the contrast of the display.
[2]
to
19