Related Manuals for Fisher & Paykel DW24U6I1
Summary of Contents for Fisher & Paykel DW24U6I1
- Page 1 DISHWASHER DW24U6I1 & DW24U2I1 models INSTALLATION GUIDE US CA 591955B 07.19...
-
Page 3: Table Of Contents
CONTENTS SAFETY AND WARNINGS COMPONENTS TOOLS TECHNICAL DATA BEFORE INSTALLATION APPLIANCE DIMENSIONS CABINETRY DIMENSIONS ELECTRICAL AND PLUMBING PREPARATION CAVITY PREPARATION ATTACH INFILL BRACKET CUSTOM DOOR PANEL PREPARATION [A] DRILL PILOT HOLES USING SUPPLIED TEMPLATE [B] MANUALLY MARK AND DRILL PILOT HOLES ATTACHING CUSTOM DOOR PANEL LEVEL DISHWASHER ALIGN APPLIANCE IN CABINETRY... -
Page 5: Safety And Warnings
SAFETY AND WARNINGS IMPORTANT SAFETY GUIDE WARNING! This dishwasher is manufactured for indoor use only. Electrical Shock Hazard Ensure to follow safety and the warnings to prevent electrical shock, injury or fire. Before installing the dishwasher, remove the house fuse or open the Ensure to remove all packaging materials supplied with the dishwasher. -
Page 6: Components
Screw-type hose clamps electrical connection Bucket – for flushing Tubing cutter Hole saw set DISHWASHER DISHWASHER DW24U2I and DW24U6I DW24U6I1 & DW24U2I1 models models the line SERVICE & WARRANTY SERVICE ET GARANTIE ΣΈΡΒΙΣ ΚΑΙ ΕΓΓΎΗΣΗ SERVIZIO E GARANZIA SERVICE & GARANTIE... -
Page 7: Technical Data
Check the electrical data on the rating label (located on the left-hand side of the dishwasher’s stainless steel inner door). If the data on the rating label are different to the specification below, consider the data as correct. DW24U2I1 models DW24U6I1 models Capacity 12 place settings... -
Page 8: Appliance Dimensions
APPLIANCE DIMENSIONS NOT TO SCALE FRONT PROFILE DW24U6I1/DW24U2I1 models APPLIANCE DIMENSIONS Overall height of appliance* 32 1/4 – 34 5/8 820 – 880 Overall width of appliance 23 3/4 (excl. side seals) Overall depth of appliance 21 3/4 (excl. custom panel & handle) Height from floor to bottom of custom panel 4 – 8... -
Page 9: Cabinetry Dimensions
CABINETRY DIMENSIONS PLAN PROFILE DW24U6I1/DW24U2I1 models CABINETRY DIMENSIONS Inside width of cavity Inside height of cavity* 32 1/4 – 34 5/8 820 – 880 Inside depth of cavity min. 22 5/8 min. 574 * depending on adjustment of levelling feet DW24U6I1/DW24U2I1 models CLEARANCE DIMENSIONS... -
Page 10: Electrical And Plumbing Preparation
ELECTRICAL AND PLUMBING PREPARATION Select plumbing option Hose connection Copper pipe connection Refer to ‘Plumbing and Drainage options’ (page 16) for more information. Left side of Final position of dishwasher against wall appliance Supply area dimensions SECTION inches... -
Page 11: Cavity Preparation
CAVITY PREPARATION IMPORTANT! COUNTERTOP The power outlet must be located in a cabinet adjacent to the dishwasher cavity. 110-120 VAC max. 15 A Moisture Water Connection 3/8” protection tape Recommended HOT (10mm) must be applied (Maximum 140°F/60°C). Supplied hose to suit 3⁄ 8 ” (9mm) male compression fitting. -
Page 12: Attach Infill Bracket
ATTACH INFILL BRACKET IMPORTANT! The infill bracket is installed as a cosmetic feature to fill the empty space visible for cabinets with cavity height of 35.5” or above. Installation of infill bracket is not needed for cabinets with ADA standard. side wings Remove upper mounting bracket and plastic plugs Install the infill bracket... -
Page 13: Custom Door Panel Preparation
CUSTOM DOOR PANEL PREPARATION IMPORTANT! Ensure the custom door panel has the correct specifications to fit the front of the dishwasher. Ensure the back and sides of the panel are completely sealed with a waterproof vapor barrier (ie polyurethane). The barrier allows the panel to withstand moisture (122°F (50°C) @ 80% RH) and prevent damage during hot and wet environment. - Page 14 ATTACHING CUSTOM DOOR PANEL Top screw detail (between panel and screw head) Fix slider bracket and screws to custom panel Hang custom panel onto the door Adust the placement of the custom panel Insert Ø 3.9 x 1/2” (13mm) screws through the top two Close the door of the dishwasher and align the screws Slide the custom panel up or down to position it in the pilot holes.
- Page 15 LEVEL DISHWASHER IMPORTANT! Ensure the appliance is leveled for proper dish rack, wash performance and door operation. To verify dishwasher is leveled, open and close the door and pull the dish racks half way out. The door should fit in the tub opening without hitting the sides. If the racks roll on their own, or the door hits the side of tub, re-level.
- Page 16 ELECTRICAL CONNECTION IMPORTANT! Ensure the power cord and connections comply with the National Electrical Code, Section 422 and/or local codes and ordinances. Maximum power cord length is 6 feet. A Power Cord Kit is available for purchase from an authorized Fisher & Paykel appliances dealer.
- Page 17 HARD PLUMBING IMPORTANT! Ensure to flush the water line into a bucket before connecting to the water inlet valve. Prepare water supply connection Connect hot water line to inlet valve inlet valve inlet valve elbow (90°) braided hose elbow (90°) gasket If using a flexible braided hose: Connect an elbow (90°) to the water inlet valve.
- Page 18 PLUMBING AND DRAINAGE OPTIONS Dishwasher and Ø 38mm Standpipe Dishwasher using drain hose joiner onto sink trap/waste tee IMPORTANT! IMPORTANT! Ensure that drain connection complies Ensure that drain connection complies with local plumbing regulations. with local plumbing regulations. Screw drain hose support to back wall at Screw drain hose support to back wall at correct height.
- Page 19 TOE KICK INSTALLATION IMPORTANT! Ensure toe kick does not protrude more than 3 9/16" (90mm) out from the dishwasher to ensure that the visibility of the floor light is not obstructed. Toekick excess (to be cut back) Door panel Toekick Refit toekick mounting plate and panel. Check door overhang and swing range.
- Page 20 SECURE THE APPLIANCE [A] FIX THE PRODUCT [B] FIX THE APPLIANCE TO ADJACENT CABINETRY TO BENCHTOP ABOVE Note: Ensure the brackets are flushed with the cabinetry. Cut off any excess portion of the brackets. Using two Ø4 x 25mm screws, secure the product to the adjacent cabinetry Using two Ø4 x 25mm screws, secure the appliance to the benchtop above through the brackets located on each side of the product chasis.
- Page 21 CONNECT INLET HOSE TO HOT WATER Plumbing — Water inlet connection IMPORTANT! Ensure the appliance is connected to the water main using the supplied new water inlet hose. Do not use old hoses. Do not shorten the inlet hose. Follow the water connection requirements. We recommend a cold water connection for best performance and energy efficiency.
- Page 22 TROUBLESHOOTING Excessive water remaining above the filter plate, after the rinse cycle (this can be displayed as fault) Check for a kinked drain hose, blocked waste connection, highloop not properly installed, drain hose not routed correctly or spray arms not in place. No water supply (this is displayed as fault) Check water is connected and turned on.
- Page 23 FINAL CHECKLIST TO BE COMPLETED BY THE INSTALLER Check all parts are installed. Ensure any packaging or tape securing the racks is removed from the dishwasher. Ensure that all panels and parts thereof are secure and final electrical tests have been Ensure appliance is level and opens and closes freely.