Cisco TelePresence System Series Hardware Upgrade Manual
  1. Manuals
  2. Brands
  3. Cisco Manuals
  4. Conference System
  5. TelePresence Profile Series
  6. Hardware upgrade manual
Cisco TelePresence System Series Hardware Upgrade Manual

Cisco TelePresence System Series Hardware Upgrade Manual

Hide thumbs Also See for TelePresence System Series:
Table of Contents

Advertisement

Quick Links

Download this manual
Cisco TelePresence System
Hardware Options & Upgrade Guide
August 5, 2009
Americas Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
http://www.cisco.com
Tel: 408 526-4000
800 553-NETS (6387)
Fax: 408 527-0883
Text Part Number: OL-16441-01

Advertisement

Table of Contents
loading

Related Manuals for Cisco TelePresence System Series

Summary of Contents for Cisco TelePresence System Series

  • Page 1 Cisco TelePresence System Hardware Options & Upgrade Guide August 5, 2009 Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 http://www.cisco.com Tel: 408 526-4000 800 553-NETS (6387) Fax: 408 527-0883 Text Part Number: OL-16441-01...
  • Page 2 OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks.

  • Page 3: Table Of Contents

    Configuring the DMP Audio for Use with the CTS 500 Cisco TelePresence Presentation Codec Parts List for Presentation Codec Adding a Presentation Codec Adding a Cisco TelePresence Presentation Codec with a Auxiliary Control Unit 2-15 Configuring a Cisco TelePresence Presentation Codec 2-15...
  • Page 4 Adding the Optional Switch 6-26 Video Signal Splitter 6-26 Upgrading a Cisco TelePresence System 3000 to a Cisco TelePresence System 3200 Upgrading a CTS 3000 to a CTS 3200: Summary Steps Required Information, Tools, and Equipment Powering Off the System...
  • Page 5 Contents Parts List 7-12 Attaching and Routing Cables 7-61 Powering On the System 7-69 Cisco TelePresence System OL-16441-01...
  • Page 6 Contents Cisco TelePresence System OL-16441-01...

  • Page 7: Preface

    The Cisco TelePresence System Hardware Options & Upgrade Guide outlines the steps and best practices to install additional items for the Cisco TelePresence Systems 1000, 3000, and 3200 and perform an upgrade from the Cisco TelePresence System 3000 to the Cisco TelePresence System 3200.

  • Page 8: Obtaining Documentation, Obtaining Support, And Security Guidelines

    Obtaining Documentation, Obtaining Support, and Security Guidelines For information on obtaining documentation, submitting a service request, and gathering additional information, see the monthly What’s New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at: http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html Subscribe to the What’s New in Cisco Product Documentation as a Really Simple Syndication (RSS) feed...

  • Page 9: Options For The Cisco Telepresence System 500

    For more information about the DMP, refer to this URL: http://www.cisco.com/en/US/products/ps7220/tsd_products_support_series_home.html If you use a Cisco TelePresence Touch device with your CTS 500 32” system, you have additional Note configuration options to control the media being played with your device after you connect the DMP.
  • Page 10 Chapter 1 Options for the Cisco TelePresence System 500 32” Cisco Digital Media Player To configure the CTS 500 32” system for use with the DMP, complete the following steps: Remove the rear codec cover. Step 1 Figure 1-1 Removing the Rear Codec Cover...
  • Page 11 Chapter 1 Options for the Cisco TelePresence System 500 32” Cisco Digital Media Player Step 2 Make the following changes to the codec connections: Remove the HD video cable from the connection labeled “Auxiliary PC Video” in Figure 1-2. Insert the HD video cable into the connection labeled “Auxiliary Input (ex. DMP)” in Figure 1-2.
  • Page 12 Connections at the Foot of the Column or Table Stand INPUT: 100-240V~, 5A, 50/60Hz If you use a Cisco Unified IP Phone as your call control device, and you have a document camera and a Note Cisco Digital Media Player (DMP) connected to the CTS 500 32”, and the document camera video does not display during a conference, use the View softkey on the Cisco Unified IP Phone to view the document camera video.

  • Page 13: Options For The Cisco Telepresence System

    Cisco TelePresence System 500 Assembly, Use & Care, and Field Replaceable Unit Guide. You can use DMPs with the Cisco Digital Media System (DMS). For more information about the DMS, refer to this URL: http://www.cisco.com/en/US/products/ps6681/products_documentation_roadmaps_list.html The DMS uses Digital Media Manager (DMM) software. For more information about DMM software and DMM appliances, refer to this URL: http://www.cisco.com/en/US/products/ps6681/tsd_products_support_series_home.html...
  • Page 14 Chapter 2 Options for the Cisco TelePresence System 500-37 Cisco Digital Media Player Connect the video for the DMP to the Digital Media Player (DMP) HD video connection on the CTS 500 Step 1 display. See Figure 2-1 for the connection.

  • Page 15: Configuring The Dmp Video For Use With The Cts 500

    Configuring the DMP Video for Use with the CTS 500 To configure the audio and video software for correct functioning with the CTS 500, complete the following steps: Log into the CIsco TelePresence System administrative GUI. Step 1 Navigate to Troubleshooting > Hardware Setup > Other Devices > DMS.

  • Page 16: Configuring The Dmp Audio For Use With The Cts 500

    Cisco TelePresence systems, refer to the Release Notes for Cisco TelePresence System for your software release. Note that Cisco does not supply the cable that connects auxiliary devices to the codec. Cisco TelePresence System...

  • Page 17: Parts List For Presentation Codec

    48-1936-01 M4 x 10mm pan head screws 48-1948-01 Adding a Presentation Codec To add the Cisco TelePresence Presentation Codec to the CTS-1000, complete the following procedure: Procedure Power off the system by performing the following steps: Step 6 Get the IP address for the system codec as follows: On the IP phone, locate Manual at the bottom of the screen and press the Manual soft key.
  • Page 18 Options for the Cisco TelePresence System 500-37 Cisco TelePresence Presentation Codec Click the Restart Cisco TelePresence System button to start the reset. The monitor goes dark and, the encircled numbers one through six appear at the bottom of the display screen on the left-hand side.
  • Page 19 Chapter 2 Options for the Cisco TelePresence System 500-37 Cisco TelePresence Presentation Codec Step 9 Insert the tab of the rear cover in the slot between the left handle/mounting bracket and the codec. Figure 2-4 Rear Cover and Left Handle/Mounting Bracket...
  • Page 20 Chapter 2 Options for the Cisco TelePresence System 500-37 Cisco TelePresence Presentation Codec Step 10 Insert the lower part of the left handle/mounting bracket into the mounting base. Figure 2-5 Left Handle/Mounting Bracket and Mounting Base Cisco TelePresence System OL-16441-01...
  • Page 21 Removal is the opposite of installation; it can be helpful to review the codec installation instructions in Cisco TelePresence System 500 Assembly, Use & Care, and Field Replaceable Unit Guide. Cisco TelePresence System...
  • Page 22 Chapter 2 Options for the Cisco TelePresence System 500-37 Cisco TelePresence Presentation Codec Step 13 Attach and route the cables between the CTS 500 and presentation codec. Figure 2-7 shows you the cabling diagram for a CTS 500 with a presentation codec.
  • Page 23 Chapter 2 Options for the Cisco TelePresence System 500-37 Cisco TelePresence Presentation Codec Figure 2-8 shows you the cabling diagram for a CTS 500 with a presentation codec and an external display. You use the display for shared presentations. Connect the presentation source to the codec using the DVI-to-VGA cable;...
  • Page 24 Chapter 2 Options for the Cisco TelePresence System 500-37 Cisco TelePresence Presentation Codec Step 14 Place the left end cap on the presentation codec assembly. Figure 2-9 Left End Cap View View Cisco TelePresence System 2-12 OL-16441-01...
  • Page 25 Chapter 2 Options for the Cisco TelePresence System 500-37 Cisco TelePresence Presentation Codec Step 15 Attach the top cover to the presentation codec assembly and route the cables through the hole in the rear center of the cover. The hole for the cables is not visible in Figure 2-10;...
  • Page 26 You might have to reboot your presentation codec several times before it becomes active. For Note information about rebooting the CTS 500, refer to the “Field-Replacement and Upgrade Disassembly Instructions” chapter of the Cisco TelePresence 500 Assembly, Use & Care, and Field-Replacement Unit Guide. Cisco TelePresence System 2-14 OL-16441-01...

  • Page 27: Adding A Cisco Telepresence Presentation Codec With A Auxiliary Control Unit

    Find the Cisco Unified IP Phone that controls your Cisco TelePresence system by clicking Find. Step 3 Click the hypertext link next to the phone that controls your Cisco TelePresence System to select it. Step 4 In the Optional Hardware area, click the Presentation Codec check box.
  • Page 28 Chapter 2 Options for the Cisco TelePresence System 500-37 Cisco TelePresence Presentation Codec Cisco TelePresence System 2-16 OL-16441-01...

  • Page 29: Options For The Cisco Telepresence System 1000

    Ethernet connection that allows you to control peripheral items. The auxiliary control unit is controlled by your CTS 1000 Administrator and can be configured to: Turn the CTS 1000 lights on during a Cisco TelePresence call and turn the lights off after the call •...

  • Page 30: Adding An Auxiliary Control Unit

    Chapter 3 Options for the Cisco TelePresence System 1000 Auxiliary Control Unit Part Description Part Number Notes Audio/Video Expansion Unit, CTS-LIGHT-CTRL, 69-1989-01 M5 x 10mm pan head screws 48-0426-01 Wood screws To be supplied by the customer. Adding an Auxiliary Control Unit To install the auxiliary control unit on your CTS 1000, complete the following steps.
  • Page 31 Chapter 3 Options for the Cisco TelePresence System 1000 Auxiliary Control Unit Step 3 Attach the auxiliary control unit to its bracket using the supplied 5 mm screws. Attach the bracket so that the shortest part of the bracket attaches to the wall; otherwise the unit is too Note wide to fit between the display supports.
  • Page 32 Chapter 3 Options for the Cisco TelePresence System 1000 Auxiliary Control Unit Step 6 Mount the auxiliary control unit to the wall using the drywall screws and drywall anchors that are provided with the kit. There are two screws on each side.

  • Page 33: Adding An Auxiliary Control Unit With A Cisco Telepresence Presentation Codec

    Cisco TelePresence systems, refer to the Release Notes for Cisco TelePresence System for your software release. Note that Cisco does not supply the cable that connects auxiliary devices to the codec. Cisco TelePresence System...

  • Page 34: Parts List For Presentation Codec

    48-1936-01 M4 x 10mm pan head screws 48-1948-01 Adding a Presentation Codec To add the Cisco TelePresence Presentation Codec to the CTS-1000, complete the following procedure: Procedure Power off the system by performing the following steps: Step 10 Get the IP address for the system codec as follows: On the IP phone, locate Manual at the bottom of the screen and press the Manual soft key.
  • Page 35 Options for the Cisco TelePresence System 1000 Cisco TelePresence Presentation Codec Click the Restart Cisco TelePresence System button to start the reset. The monitor goes dark and, the encircled numbers one through six appear at the bottom of the display screen on the left-hand side.
  • Page 36 Chapter 3 Options for the Cisco TelePresence System 1000 Cisco TelePresence Presentation Codec Step 13 Insert the tab of the rear cover in the slot between the left handle/mounting bracket and the codec. Figure 3-4 Rear Cover and Left Handle/Mounting Bracket...
  • Page 37 Chapter 3 Options for the Cisco TelePresence System 1000 Cisco TelePresence Presentation Codec Step 14 Insert the lower part of the left handle/mounting bracket into the mounting base. Figure 3-5 Left Handle/Mounting Bracket and Mounting Base Cisco TelePresence System OL-16441-01...
  • Page 38 Chapter 3 Options for the Cisco TelePresence System 1000 Cisco TelePresence Presentation Codec Step 15 Reattach the right handle/mounting bracket to the codec assembly. Figure 3-6 Right Handle/Mounting Bracket and Codec Assembly Cisco TelePresence System 3-10 OL-16441-01...
  • Page 39 Chapter 3 Options for the Cisco TelePresence System 1000 Cisco TelePresence Presentation Codec Step 16 Access the codec by removing the front panel from the frame. Complete the following steps: Remove the black speaker grille from the top of the front panel by grasping the sides until the pins pop out of the holes.
  • Page 40 Chapter 3 Options for the Cisco TelePresence System 1000 Cisco TelePresence Presentation Codec Step 17 Attach and route the cables between the CTS 1000 and presentation codec. Figure 3-8 shows you the cabling diagram for a CTS 1000 with a presentation codec.
  • Page 41 Chapter 3 Options for the Cisco TelePresence System 1000 Cisco TelePresence Presentation Codec Figure 3-9 shows you the cabling diagram for a CTS 1000 with an external display. You use the display for shared presentations. If your CTS 1000 does not have an auxiliary control unit, omit the video connection between the Note presentation display and the auxiliary control unit.
  • Page 42 Chapter 3 Options for the Cisco TelePresence System 1000 Cisco TelePresence Presentation Codec Figure 3-10 shows you the cabling diagram for a CTS 1000 with a presentation codec and an external display. You use the display for shared presentations. Connect the presentation source to the codec using the DVI-to-VGA cable;...
  • Page 43 Chapter 3 Options for the Cisco TelePresence System 1000 Cisco TelePresence Presentation Codec Step 18 Place the left end cap on the presentation codec assembly. Figure 3-11 Left End Cap View View Cisco TelePresence System 3-15 OL-16441-01...
  • Page 44 Chapter 3 Options for the Cisco TelePresence System 1000 Cisco TelePresence Presentation Codec Step 19 Attach the top cover to the presentation codec assembly and route the cables through the hole in the rear center of the cover. The hole for the cables is not visible in Figure 3-12;...

  • Page 45: Adding A Cisco Telepresence Presentation Codec With A Auxiliary Control Unit

    Unit Guide. Adding a Cisco TelePresence Presentation Codec with a Auxiliary Control Unit To add a presentation codec to an CTS 1000 with an auxiliary control unit, complete the steps in the “Adding a Presentation Codec” section on page 3-6...

  • Page 46: Configuring A Cisco Telepresence Presentation Codec

    Find the Cisco Unified IP Phone that controls your Cisco TelePresence system by clicking Find. Step 3 Click the hypertext link next to the phone that controls your Cisco TelePresence System to select it. Step 4 In the Optional Hardware area, click the Presentation Codec check box.

  • Page 47: Cisco Digital Media Player

    Web, and dynamic content on digital displays. For more information about the DMP, refer to this URL: http://www.cisco.com/en/US/products/ps7220/tsd_products_support_series_home.html You can use DMPs with the Cisco Digital Media System (DMS). For more information about the DMS, refer to this URL: http://www.cisco.com/en/US/products/ps6681/products_documentation_roadmaps_list.html The DMS uses Digital Media Manager (DMM) software.

  • Page 48: Options For The Cisco Telepresence System 1100

    Chapter 4 Options for the Cisco TelePresence System 1100 Cisco Digital Media Player Connect the video for the DMP to the Digital Media Player (DMP) HD video connection on the Step 1 CTS 1100 display. See Figure 4-1 for the connection.

  • Page 49: Configuring The Dmp Video For Use With The Cts 1100

    Configuring the DMP Video for Use with the CTS 1100 To configure the audio and video software for correct functioning with the CTS 1100, complete the following steps: Log into the CIsco TelePresence System administrative GUI. Step 1 Navigate to Troubleshooting > Hardware Setup > Other Devices > DMS.

  • Page 50: Configuring The Dmp Audio For Use With The Cts 1100

    Cisco TelePresence systems, refer to the Release Notes for Cisco TelePresence System for your software release. Note that Cisco does not supply the cable that connects auxiliary devices to the codec. Cisco TelePresence System...
  • Page 51 Secondary (Presentation) codec 800-28202-xx Adding a Presentation Codec To add the Cisco TelePresence Presentation Codec to the CTS-1000, complete the following procedure: Procedure Step 1 Remove the cabinet cover by holding it from underneath and raising it slightly; then, grasp it from the top and gently rock it towards you to disengage it from the slots in the upper part of the cabinet.
  • Page 52 4-3. Note that the Note Cisco logo is hidden and the perforated grill on the codec faces the left side of the display cabinet. Slide the codec from the right to the left until the top of the codec slides past the spring-loaded posts inside the cabinet.
  • Page 53 Chapter 4 Options for the Cisco TelePresence System 1100 Cisco TelePresence Presentation Codec Step 4 Attach the cables to the presentation codec and auxiliary display by following the cabling diagram in Figure 4-4. Figure 4-4 Cabling Diagram for Presentation Codec With Auxiliary Display...
  • Page 54 Chapter 4 Options for the Cisco TelePresence System 1100 Cisco TelePresence Presentation Codec Step 5 Power on the system by turning the power switch on the PDU that is inside of the cabinet to the “ON” position. Write down the IP address that displays on the bottom right corner of the display screens. This is the Note address of the primary codec unit.
  • Page 55 Chapter 4 Options for the Cisco TelePresence System 1100 Cisco TelePresence Presentation Codec Figure 4-5 Attaching the Cabinet Cover to the Cabinet Cisco TelePresence System OL-16441-01...
  • Page 56 Cisco TelePresence Presentation Codec Step 7 Log in to the Cisco TelePresence Administration GUI by opening a browser on a computer that is connected to the network, then typing in the IP address of the primary codec unit into the browser address bar.
  • Page 57 Web, and dynamic content on digital displays. For more information about the DMP, refer to this URL: http://www.cisco.com/en/US/products/ps7220/tsd_products_support_series_home.html You can use DMPs with the Cisco Digital Media System (DMS). For more information about the DMS, refer to this URL: http://www.cisco.com/en/US/products/ps6681/products_documentation_roadmaps_list.html The DMS uses Digital Media Manager (DMM) software.
  • Page 58 Chapter 5 Options for the Cisco TelePresence System 1300 Cisco Digital Media Player Connect the video for the DMP to the Digital Media Player (DMP) HD video connection on the Step 1 CTS 1300 display. See Figure 5-1 for the connection.

  • Page 59: Configuring The Dmp Video For Use With The Cts 1300

    Configuring the DMP Video for Use with the CTS 1300 To configure the audio and video software for correct functioning with the CTS 1300, complete the following steps: Log into the CIsco TelePresence System administrative GUI. Step 1 Navigate to Troubleshooting > Hardware Setup > Other Devices > DMS.

  • Page 60: Configuring The Dmp Audio For Use With The Cts 1300

    Cisco TelePresence systems, refer to the Release Notes for Cisco TelePresence System for your software release. Note that Cisco does not supply the cable that connects auxiliary devices to the codec. Cisco TelePresence System...

  • Page 61: Parts List For Presentation Codec

    Secondary (Presentation) codec 800-28202-xx Adding a Presentation Codec To add the Cisco TelePresence Presentation Codec to the CTS-1000, complete the following procedure: Procedure Step 1 Remove the cabinet cover by holding it from underneath and raising it slightly; then, grasp it from the top and gently rock it towards you to disengage it from the slots in the upper part of the cabinet.
  • Page 62 5-3. Note that the Note Cisco logo is hidden and the perforated grill on the codec faces the left side of the display cabinet. Slide the codec from the right to the left until the top of the codec slides past the spring-loaded posts inside the cabinet.
  • Page 63 Chapter 5 Options for the Cisco TelePresence System 1300 Cisco TelePresence Presentation Codec Step 4 Attach the cables to the presentation codec and auxiliary display by following the cabling diagram in Figure 5-4. Ignore the connections for the microphone, camera, and speakers in the following diagram.
  • Page 64 Chapter 5 Options for the Cisco TelePresence System 1300 Cisco TelePresence Presentation Codec Step 5 Power on the system by turning the power switch on the PDU that is inside of the cabinet to the “ON” position. Write down the IP address that displays on the bottom right corner of the display screens. This is the Note address of the primary codec unit.
  • Page 65 Chapter 5 Options for the Cisco TelePresence System 1300 Cisco TelePresence Presentation Codec Figure 5-5 Attaching the Cabinet Cover to the Cabinet Cisco TelePresence System OL-16441-01...
  • Page 66 Cisco TelePresence Presentation Codec Step 7 Log in to the Cisco TelePresence Administration GUI by opening a browser on a computer that is connected to the network, then typing in the IP address of the primary codec unit into the browser address bar.

  • Page 67: Options For The Cisco Telepresence System 3000, 3010, 3200, And 3210

    Cisco TelePresence system administrator and can be configured to: • Turn the Cisco TelePresence system lights on during a Cisco TelePresence call and turn the lights five minutes after the call completes. This is the default behavior if you configure Power Control in Cisco Unified Communications Manager to be “On with calls only”.

  • Page 68: Parts List For Auxiliary Control Unit

    Chapter 6 Options for the Cisco TelePresence System 3000, 3010, 3200, and 3210 Auxiliary Control Unit Parts List for Auxiliary Control Unit Part Description Part Number Notes Audio/Video Expansion Unit, CTS-LIGHT-CTRL, 69-1989-01 Auxiliary Control Unit 69-1989-01 Bracket for auxiliary control unit...

  • Page 69: Adding An Auxiliary Control Unit

    Chapter 6 Options for the Cisco TelePresence System 3000, 3010, 3200, and 3210 Auxiliary Control Unit Adding an Auxiliary Control Unit The following illustrations and steps describe how to attach the auxiliary control unit to your Cisco TelePresence system. Turn off the power to the side PDUs and unplug the power cables for the lighting assembly.
  • Page 70 Chapter 6 Options for the Cisco TelePresence System 3000, 3010, 3200, and 3210 Auxiliary Control Unit Step 2 Attach the auxiliary control unit to the rear of the display assembly. Figure 6-2 Auxiliary Control Unit If your installation has a PDU in the center of the display assembly (roughly in the same location as the Note auxiliary control unit), remove the PDU during this step.
  • Page 71 Chapter 6 Options for the Cisco TelePresence System 3000, 3010, 3200, and 3210 Auxiliary Control Unit Step 3 Plug the jumper cords for the lights and the projector serial cable into the auxiliary control unit. Figure 6-3 Cable Routing for Auxiliary Control Unit...

  • Page 72: Configuring An Auxiliary Control Unit

    Adding a Auxiliary Control Unit with a Cisco TelePresence Presentation Codec To add an auxiliary control unit to a Cisco TelePresence system with a presentation codec, complete the steps in the “Adding an Auxiliary Control Unit” section on page 6-3...

  • Page 73: Adding A Cisco Telepresence Presentation Codec-Cisco Telepresence System 3000 And 3200

    Adding a Cisco TelePresence Presentation Codec—Cisco TelePresence System 3000 and 3200 To add the Cisco TelePresence Presentation Codec to your CTS 3000 or CTS 3200, perform the following procedure: Turn the power switches for the two left PDUs and single right PDU to the Off position.
  • Page 74 Step 2 The projector screen is attached to the Cisco TelePresence assembly by clips that are on the top edge and side of the screen. To remove the screen, gently pull outward on the screen where the clips are located.
  • Page 75 Chapter 6 Options for the Cisco TelePresence System 3000, 3010, 3200, and 3210 Cisco TelePresence Presentation Codec Step 3 Remove the three speaker assemblies. If required, disconnect the speaker cables. Figure 6-6 Removing the Speaker Assemblies Cisco TelePresence System OL-16441-01...
  • Page 76 Chapter 6 Options for the Cisco TelePresence System 3000, 3010, 3200, and 3210 Cisco TelePresence Presentation Codec Step 4 Unscrew the four screws that attach the codec safety tray to the frame feet and remove the codec tray. Figure 6-7...
  • Page 77 Chapter 6 Options for the Cisco TelePresence System 3000, 3010, 3200, and 3210 Cisco TelePresence Presentation Codec Step 5 Attach the cable management bar to the presentation codec. Figure 6-8 Cable Management Bar Cisco TelePresence System 6-11 OL-16441-01...
  • Page 78 Chapter 6 Options for the Cisco TelePresence System 3000, 3010, 3200, and 3210 Cisco TelePresence Presentation Codec Step 6 Attach the attachment brackets to the presentation codec. Figure 6-9 Presentation Codec and Attachment Brackets Cisco TelePresence System 6-12 OL-16441-01...
  • Page 79 Chapter 6 Options for the Cisco TelePresence System 3000, 3010, 3200, and 3210 Cisco TelePresence Presentation Codec Step 7 Place the double-wide codec tray in between the frame feet and secure it with the screws. Figure 6-10 Double-Wide Codec Tray...
  • Page 80 Chapter 6 Options for the Cisco TelePresence System 3000, 3010, 3200, and 3210 Cisco TelePresence Presentation Codec Step 8 Place the presentation codec in the front of the new codec tray and attach it to the front feet of the display stand.
  • Page 81 Options for the Cisco TelePresence System 3000, 3010, 3200, and 3210 Cisco TelePresence Presentation Codec Step 9 Route the signal cables for the presentation codec using one of the following diagrams: For a standard Cisco TelePresence system installation, use the following wiring diagram for the • presentation codec. Figure 6-12...
  • Page 82 If you have an Auxiliary Control Unit, substitute the signal cabling between the presentation codec and the primary codec with the alternate cabling for the Auxiliary Control Unit. For a list of the external displays that Cisco TelePresence supports, refer to the Release Notes for Cisco TelePresence System for your software release.
  • Page 83 Chapter 6 Options for the Cisco TelePresence System 3000, 3010, 3200, and 3210 Cisco TelePresence Presentation Codec Figure 6-13 Cable Routing for Presentation Codec, Auxiliary Control Unit, Document Camera and External Display Auxiliary Control Unit SERI AL PORTS RESET 10/ 100 NETW ORK PORTS...
  • Page 84 Chapter 6 Options for the Cisco TelePresence System 3000, 3010, 3200, and 3210 Cisco TelePresence Presentation Codec Step 10 Route the power cables for the presentation codec. Figure 6-14 Presentation Codec Cable Routing Power Note Your installation might differ from this diagram. There might be one PDU on the left side of the display structure, rather than two;...

  • Page 85: Adding A Cisco Telepresence Presentation Codec-Cisco Telepresence System 3010 And 3210

    Cisco TelePresence Presentation Codec Step 11 Power on the Cisco TelePresence system by turning the power switches to the On position for the two left PDUs, single right PDU, and the PDU on the central display if it is present.
  • Page 86 Chapter 6 Options for the Cisco TelePresence System 3000, 3010, 3200, and 3210 Cisco TelePresence Presentation Codec Figure 6-15 PDU Location Power Cisco TelePresence System 6-20 OL-16441-01...
  • Page 87 Chapter 6 Options for the Cisco TelePresence System 3000, 3010, 3200, and 3210 Cisco TelePresence Presentation Codec Step 2 From the rear of the system, remove the primary codec and set it aside. If necessary, disconnect the cables from the primary codec.
  • Page 88 IP Phone Network For a Cisco TelePresence system installation that uses an optional document camera, external display, or HDMI splitter for multiple video displays, use the following wiring diagram for the presentation codec. If you have an Auxiliary Control Unit, substitute the signal cabling between the presentation codec and the primary codec with the alternate cabling for the Auxiliary Control Unit.
  • Page 89 Options for the Cisco TelePresence System 3000, 3010, 3200, and 3210 Cisco TelePresence Presentation Codec Figure 6-18 Figure 8-12 Cabling Diagram: Cisco TelePresence system Installations with an External Display and Document Camera Auxiliary Control Unit SERIAL P O R TS...

  • Page 90: Configuring A Cisco Telepresence Presentation Codec

    Find the Cisco Unified IP Phone that controls your Cisco TelePresence system by clicking Find. Step 3 Click the hypertext link next to the phone that controls your Cisco TelePresence System to select it. Step 4 In the Optional Hardware area, click the Presentation Codec check box.

  • Page 91: Optional Switch For Ethernet Connectivity

    Chapter 6 Options for the Cisco TelePresence System 3000, 3010, 3200, and 3210 Optional Switch for Ethernet Connectivity • Connect the other Ethernet port of the auxiliary control unit to the Presentation Codec Ethernet port (white/red Ethernet connection on the presentation codec).

  • Page 92: Adding The Optional Switch

    Using External Devices with Your Cisco TelePresence System—Cisco cannot guarantee the Note performance of any external device, so Cisco recommends that you choose good quality external devices to optimize performance of the Cisco TelePresence system. The Cisco TelePresence System works best when you attach suitable devices using good quality cables and connectors.
  • Page 93 Chapter 6 Options for the Cisco TelePresence System 3000, 3010, 3200, and 3210 Upgrading a CTS 3000 to a CTS 3200 In European Union countries, use only devices that are fully compliant with the EMC Directive Caution [2004/108/EC]. GEFEN EXT-HDMI-144 or EXT-HDMI-144-BLK •...
  • Page 94 Warning as tabletop supports while you attach tabletop segments. They can fall and cause injury or damage. Cisco suggests you use the accessory cabinets to support and stabilize the table segments as you install them. Power down the system. See the “Powering Off the System”...

  • Page 95: Required Information, Tools, And Equipment

    Locate the Phone pane in the upper left-hand corner of the administrator page and select Step 6 Troubleshooting > System Reset. The Restart Cisco TelePresence System button appears at the top of the window. Click the Restart Cisco TelePresence System button to start the reset.

  • Page 96: Replacing The Primary Codec

    Make a note of the MAC address of the new primary codec. The MAC address should be printed on a Step 7 sticker on the codec. You configure Cisco Unified Communications Manager to use the new MAC address in the “Powering On the System”...
  • Page 97 Chapter 6 Options for the Cisco TelePresence System 3000, 3010, 3200, and 3210 Upgrading a CTS 3000 to a CTS 3200 Step 8 Attach the cable management bar to the new primary codec. Figure 6-21 Cable Management Bar Cisco TelePresence System...
  • Page 98 Chapter 6 Options for the Cisco TelePresence System 3000, 3010, 3200, and 3210 Upgrading a CTS 3000 to a CTS 3200 Step 9 Attach the brackets to the new primary codec. Insert the new codec into the display stand from the rear of the display assembly and secure it with the Step 10 screws.

  • Page 99: Removing And Replacing The Camera Lenses

    Chapter 6 Options for the Cisco TelePresence System 3000, 3010, 3200, and 3210 Upgrading a CTS 3000 to a CTS 3200 Removing and Replacing the Camera Lenses Take care not to scratch or mar the display screen during the replacement procedure.
  • Page 100 Chapter 6 Options for the Cisco TelePresence System 3000, 3010, 3200, and 3210 Upgrading a CTS 3000 to a CTS 3200 Step 3 Carefully unscrew the lenses from the camera assembly. Figure 6-22 Removing Lenses from The Camera Assembly Attach the new lenses to the camera assembly. Tighten until the lenses are seated and finger-tight but do Step 4 not overtighten.

  • Page 101: Adding The Audio/Video Extension Unit

    Options for the Cisco TelePresence System 3000, 3010, 3200, and 3210 Upgrading a CTS 3000 to a CTS 3200 Adding the Audio/Video Extension Unit To add the audio/video extension unit for the Cisco TelePresence 3000, you need the following tools and equipment: •...
  • Page 102 Chapter 6 Options for the Cisco TelePresence System 3000, 3010, 3200, and 3210 Upgrading a CTS 3000 to a CTS 3200 Step 3 Attach the audio/video extension unit to the display assembly. Figure 6-24 Audio Extension Unit and Display Assembly Attach the new extension unit to the display structure with the screws that are provided in the package.

  • Page 103: Adding The Auxiliary Control Unit

    Adding the Auxiliary Control Unit If your system already has an auxiliary control unit, bypass this procedure. Note To add the auxiliary control unit Cisco TelePresence 3000, you need the following tools and equipment: • Large Phillips head screwdriver Masking tape •...
  • Page 104 Chapter 6 Options for the Cisco TelePresence System 3000, 3010, 3200, and 3210 Upgrading a CTS 3000 to a CTS 3200 Step 3 Attach the auxiliary control unit to the rear of the display assembly with the screws that are provided in the package.

  • Page 105: Building The Second Row Table Assembly

    Chapter 6 Options for the Cisco TelePresence System 3000, 3010, 3200, and 3210 Upgrading a CTS 3000 to a CTS 3200 Building the Second Row Table Assembly To build the second row table assembly, complete the following procedure. Use the provided parts list as a guide for the illustrations in this section.
  • Page 106 Chapter 6 Options for the Cisco TelePresence System 3000, 3010, 3200, and 3210 Upgrading a CTS 3000 to a CTS 3200 Remove the Metal packaging braces from the Molded foam bumpers. Step 1 Figure 6-26 Metal packaging braces and their Molded foam bumpers...
  • Page 107 Chapter 6 Options for the Cisco TelePresence System 3000, 3010, 3200, and 3210 Upgrading a CTS 3000 to a CTS 3200 Step 2 Assemble the seven Molded foam bumpers and the seven Table leg bases. Figure 6-27 Four Molded foam bumpers and the four Table leg bases...
  • Page 108 Chapter 6 Options for the Cisco TelePresence System 3000, 3010, 3200, and 3210 Upgrading a CTS 3000 to a CTS 3200 Step 3 Attach the first set of support brackets for the gutter and privacy panel to the table legs.
  • Page 109 Chapter 6 Options for the Cisco TelePresence System 3000, 3010, 3200, and 3210 Upgrading a CTS 3000 to a CTS 3200 Step 4 Attach the second set of five support brackets to the table legs. Figure 6-29 Gutter and Privacy Panel Support Brackets, Type 2...
  • Page 110 Chapter 6 Options for the Cisco TelePresence System 3000, 3010, 3200, and 3210 Upgrading a CTS 3000 to a CTS 3200 Step 5 While one or more assistants keep the table legs steady, attach the Section 1 gutter panel to the Section 1 table legs.
  • Page 111 Chapter 6 Options for the Cisco TelePresence System 3000, 3010, 3200, and 3210 Upgrading a CTS 3000 to a CTS 3200 Step 6 Attach the Section 2 gutter panel to the Section 2 table legs. Figure 6-31 Section 2 Gutter Panel...
  • Page 112 Chapter 6 Options for the Cisco TelePresence System 3000, 3010, 3200, and 3210 Upgrading a CTS 3000 to a CTS 3200 Step 7 Attach the Section 3 gutter panel to the Section 3 table legs. Figure 6-32 Section 3 Gutter Panel...
  • Page 113 Chapter 6 Options for the Cisco TelePresence System 3000, 3010, 3200, and 3210 Upgrading a CTS 3000 to a CTS 3200 Step 8 Attach the Section 4 gutter panel to the Section 4 table legs. Figure 6-33 Section 4 Gutter Panel...
  • Page 114 Chapter 6 Options for the Cisco TelePresence System 3000, 3010, 3200, and 3210 Upgrading a CTS 3000 to a CTS 3200 Step 9 Attach the left Section 5 gutter panels to the remaining table legs. Figure 6-34 Section 5 (Left) Gutter Panels...
  • Page 115 Chapter 6 Options for the Cisco TelePresence System 3000, 3010, 3200, and 3210 Upgrading a CTS 3000 to a CTS 3200 Step 10 Attach the right Section 5 gutter panels to the remaining table legs. Figure 6-35 Section 5 (Right) Gutter Panels...
  • Page 116 Chapter 6 Options for the Cisco TelePresence System 3000, 3010, 3200, and 3210 Upgrading a CTS 3000 to a CTS 3200 Step 11 Assemble the I/O modules for the outside left and outside right molded foam bumpers. The outside left and outside right molded foam bumpers only have one I/O module each. The inner...
  • Page 117 Chapter 6 Options for the Cisco TelePresence System 3000, 3010, 3200, and 3210 Upgrading a CTS 3000 to a CTS 3200 Step 12 Assemble the I/O modules for the inner molded foam bumpers. Figure 6-37 Foam Bumper Assembly 47 48 49 The Ethernet cables are of different lengths.
  • Page 118 Chapter 6 Options for the Cisco TelePresence System 3000, 3010, 3200, and 3210 Upgrading a CTS 3000 to a CTS 3200 Step 13 Insert the second row PDUs in the lower cable gutters. Figure 6-38 PDU Cable Routing Cisco TelePresence System...
  • Page 119 Chapter 6 Options for the Cisco TelePresence System 3000, 3010, 3200, and 3210 Upgrading a CTS 3000 to a CTS 3200 Step 14 Attach the first set of floating brackets to the table assembly. Figure 6-39 Floating Brackets, Type 1...
  • Page 120 Chapter 6 Options for the Cisco TelePresence System 3000, 3010, 3200, and 3210 Upgrading a CTS 3000 to a CTS 3200 Step 15 Attach the second set of floating brackets to the table assembly. Figure 6-40 Floating Brackets, Type 2...
  • Page 121 Chapter 6 Options for the Cisco TelePresence System 3000, 3010, 3200, and 3210 Upgrading a CTS 3000 to a CTS 3200 Step 16 Attach the privacy panel hangers to the table assembly. Figure 6-41 Privacy Panel Hanger Brackets Cisco TelePresence System...
  • Page 122 Chapter 6 Options for the Cisco TelePresence System 3000, 3010, 3200, and 3210 Upgrading a CTS 3000 to a CTS 3200 Step 17 Place the section 1 and section 2 tabletops on the table assembly, insert the plastic spline in the slot of table section 1, and join the tables together, then insert and tighten the draw bolts evenly on each side until the tabletop sections are joined together.
  • Page 123 Chapter 6 Options for the Cisco TelePresence System 3000, 3010, 3200, and 3210 Upgrading a CTS 3000 to a CTS 3200 Step 18 Place the Section 3 tabletop on the table assembly, insert the spline in the slot between the two tabletops, and use the draw bolts to join table tops 1 and 3 together.
  • Page 124 Chapter 6 Options for the Cisco TelePresence System 3000, 3010, 3200, and 3210 Upgrading a CTS 3000 to a CTS 3200 Step 19 Join table section 4 to table section 2 using the draw bolts and spline. Figure 6-44 Tabletop Section 4...
  • Page 125 Chapter 6 Options for the Cisco TelePresence System 3000, 3010, 3200, and 3210 Upgrading a CTS 3000 to a CTS 3200 Step 20 Place the left tabletop section 5 on the table assembly and join it to the section 3 tabletop using the draw bolts and spline.
  • Page 126 Chapter 6 Options for the Cisco TelePresence System 3000, 3010, 3200, and 3210 Upgrading a CTS 3000 to a CTS 3200 Step 21 Place the right tabletop section 5 on the table assembly and join it to the section 4 tabletop.
  • Page 127 Chapter 6 Options for the Cisco TelePresence System 3000, 3010, 3200, and 3210 Upgrading a CTS 3000 to a CTS 3200 Step 22 Attach the left tabletop end to tabletop section 5 using the using the draw bolts, spline and alignment plate.
  • Page 128 Chapter 6 Options for the Cisco TelePresence System 3000, 3010, 3200, and 3210 Upgrading a CTS 3000 to a CTS 3200 Step 23 Attach the Right tabletop end. Figure 6-48 Right Tabletop End 7(1) Cisco TelePresence System 6-62 OL-16441-01...
  • Page 129 Chapter 6 Options for the Cisco TelePresence System 3000, 3010, 3200, and 3210 Upgrading a CTS 3000 to a CTS 3200 Step 24 Attach tabletop sections 1 and 2 to the table leg. Figure 6-49 Tabletop Sections 1 and 2 and Table Leg...
  • Page 130 Chapter 6 Options for the Cisco TelePresence System 3000, 3010, 3200, and 3210 Upgrading a CTS 3000 to a CTS 3200 Step 25 Attach tabletop sections 1 and 3 to the table leg. Figure 6-50 Tabletop Sections 1 and 3 and Table Leg...
  • Page 131 Chapter 6 Options for the Cisco TelePresence System 3000, 3010, 3200, and 3210 Upgrading a CTS 3000 to a CTS 3200 Step 26 Attach tabletop sections 2 and 4 to the table leg. Figure 6-51 Tabletop Sections 2 and 4 and Table Leg...
  • Page 132 Chapter 6 Options for the Cisco TelePresence System 3000, 3010, 3200, and 3210 Upgrading a CTS 3000 to a CTS 3200 Step 27 Attach tabletop sections 3 and 5 to the table leg. Figure 6-52 Tabletop Sections 3 and 5 and Table Leg...
  • Page 133 Chapter 6 Options for the Cisco TelePresence System 3000, 3010, 3200, and 3210 Upgrading a CTS 3000 to a CTS 3200 Step 28 Attach tabletop sections 4 and 5 to the table leg. Figure 6-53 Tabletop Sections 4 and 5 and Table Leg...
  • Page 134 Chapter 6 Options for the Cisco TelePresence System 3000, 3010, 3200, and 3210 Upgrading a CTS 3000 to a CTS 3200 Step 29 Attach the reinforcement screws for the gutter panels. Figure 6-54 Gutter Panel Reinforcement Screws Cisco TelePresence System...
  • Page 135 Chapter 6 Options for the Cisco TelePresence System 3000, 3010, 3200, and 3210 Upgrading a CTS 3000 to a CTS 3200 Step 30 Attach the panel end brace to the table leg and left tabletop end and attach the table leg to the tabletop and tabletop end.
  • Page 136 Chapter 6 Options for the Cisco TelePresence System 3000, 3010, 3200, and 3210 Upgrading a CTS 3000 to a CTS 3200 Step 31 Attach the panel end brace to the table leg and right tabletop end, then attach the table leg to the tabletop and tabletop end.
  • Page 137 Chapter 6 Options for the Cisco TelePresence System 3000, 3010, 3200, and 3210 Upgrading a CTS 3000 to a CTS 3200 Step 32 Attach the privacy panel support bracket to the underside of table section 1. Figure 6-57 Section 1 Privacy Panel Support Bracket...
  • Page 138 Chapter 6 Options for the Cisco TelePresence System 3000, 3010, 3200, and 3210 Upgrading a CTS 3000 to a CTS 3200 Step 33 Attach the privacy panel support bracket to the underside of table section 2. Figure 6-58 Section 2 Privacy Panel Support Bracket...
  • Page 139 Chapter 6 Options for the Cisco TelePresence System 3000, 3010, 3200, and 3210 Upgrading a CTS 3000 to a CTS 3200 Step 34 Attach the privacy panel support bracket to the underside of table section 3. Figure 6-59 Section 3 Privacy Panel Support Bracket...
  • Page 140 Chapter 6 Options for the Cisco TelePresence System 3000, 3010, 3200, and 3210 Upgrading a CTS 3000 to a CTS 3200 Step 35 Attach the privacy panel support bracket to the underside of table section 4. Figure 6-60 Section 4 Privacy Panel Support Bracket...
  • Page 141 Chapter 6 Options for the Cisco TelePresence System 3000, 3010, 3200, and 3210 Upgrading a CTS 3000 to a CTS 3200 Step 36 Attach the privacy panel support bracket to the underside of left table section 5. Figure 6-61 Left Section 5 Privacy Panel Support Bracket...
  • Page 142 Chapter 6 Options for the Cisco TelePresence System 3000, 3010, 3200, and 3210 Upgrading a CTS 3000 to a CTS 3200 Step 37 Attach the privacy panel support bracket to the underside of right table section 5. Figure 6-62 Right Section 5 Privacy Panel Support Bracket...
  • Page 143 Chapter 6 Options for the Cisco TelePresence System 3000, 3010, 3200, and 3210 Upgrading a CTS 3000 to a CTS 3200 Step 38 Attach one microphone to each table segment and attach the microphone extension cords to the microphone cables. There are six microphones for the second row table.
  • Page 144 Chapter 6 Options for the Cisco TelePresence System 3000, 3010, 3200, and 3210 Upgrading a CTS 3000 to a CTS 3200 Step 39 Lift the privacy panel for table section 1 into position until it seats on the locating pins on the table assembly;...
  • Page 145 Chapter 6 Options for the Cisco TelePresence System 3000, 3010, 3200, and 3210 Upgrading a CTS 3000 to a CTS 3200 Step 40 Attach the privacy panel for section 2 to the table assembly. Figure 6-65 Section 2 Privacy Panel...
  • Page 146 Chapter 6 Options for the Cisco TelePresence System 3000, 3010, 3200, and 3210 Upgrading a CTS 3000 to a CTS 3200 Step 41 Attach the privacy panel for section 3 to the table assembly. Figure 6-66 Section 3 Privacy Panel...
  • Page 147 Chapter 6 Options for the Cisco TelePresence System 3000, 3010, 3200, and 3210 Upgrading a CTS 3000 to a CTS 3200 Step 42 Attach the privacy panel for section 4 to the table assembly. Figure 6-67 Section 4 Privacy Panel...
  • Page 148 Chapter 6 Options for the Cisco TelePresence System 3000, 3010, 3200, and 3210 Upgrading a CTS 3000 to a CTS 3200 Step 43 Attach the privacy panel for left section 5 to the table assembly. Figure 6-68 Left Section 5 Privacy Panel...
  • Page 149 Chapter 6 Options for the Cisco TelePresence System 3000, 3010, 3200, and 3210 Upgrading a CTS 3000 to a CTS 3200 Step 44 Attach the privacy panel for right section 5 to the table assembly. Figure 6-69 Section 5 Privacy Panel...
  • Page 150 Chapter 6 Options for the Cisco TelePresence System 3000, 3010, 3200, and 3210 Upgrading a CTS 3000 to a CTS 3200 Step 45 Adjust panels until all seams between the panels are even, then fully tighten the knob screws. Figure 6-70...
  • Page 151 Chapter 6 Options for the Cisco TelePresence System 3000, 3010, 3200, and 3210 Upgrading a CTS 3000 to a CTS 3200 Step 46 Attach the cable cover for the right end privacy panel. Figure 6-71 Privacy Panel End Pieces Install the cable cover so that it hides the cables that come out of the right side of the table section.
  • Page 152 Chapter 6 Options for the Cisco TelePresence System 3000, 3010, 3200, and 3210 Upgrading a CTS 3000 to a CTS 3200 Step 47 Attach the privacy panel end pieces and the cable cover for the right end privacy panel. Figure 6-72...
  • Page 153 Chapter 6 Options for the Cisco TelePresence System 3000, 3010, 3200, and 3210 Upgrading a CTS 3000 to a CTS 3200 Step 48 Position the second row table so that the trailing edge of the first row table is exactly 59 inches (150 cm) behind the leading edge of the second row table.
  • Page 154 Chapter 6 Options for the Cisco TelePresence System 3000, 3010, 3200, and 3210 Upgrading a CTS 3000 to a CTS 3200 Attaching and Routing Cables To attach and route cables for the CTS 3200 upgrade, complete the following steps. Route the second row microphone cables.
  • Page 155 Chapter 6 Options for the Cisco TelePresence System 3000, 3010, 3200, and 3210 Upgrading a CTS 3000 to a CTS 3200 Step 2 If your installation uses wired Ethernet for the second row participants, attach the Ethernet cables to the modules in the foam bumpers and route the Ethernet cables.
  • Page 156 Chapter 6 Options for the Cisco TelePresence System 3000, 3010, 3200, and 3210 Upgrading a CTS 3000 to a CTS 3200 Step 3 Route the power cables for the second row table. Figure 6-75 Second Row Table Power Cable Routing...
  • Page 157 Options for the Cisco TelePresence System 3000, 3010, 3200, and 3210 Upgrading a CTS 3000 to a CTS 3200 Step 4 Route the cables for the Cisco Unified IP phone and VGA peripheral. Figure 6-76 Microphone, IP Phone and VGA Peripheral Cable Routing...
  • Page 158 Chapter 6 Options for the Cisco TelePresence System 3000, 3010, 3200, and 3210 Upgrading a CTS 3000 to a CTS 3200 Step 5 Attach the microphone cables, noting that the center microphone on the first row (microphone 1) routes directly into the primary codec.
  • Page 159 Upgrading a CTS 3000 to a CTS 3200 Figure 6-77 displays the rear view of the Cisco TelePresence System. Left and right are reversed. Note Before plugging cables into the Codec, label each one. For example, Left Speaker, Center Speaker.
  • Page 160 The camera cluster can experience radio frequency interference issues if the camera Ethernet and Note HD video cables are routed, bundled, or tied together. Cisco recommends that you route the Ethernet and HD video cables separately and use cable ties to tie them to opposite sides of the frame. In addition,...
  • Page 161 Options for the Cisco TelePresence System 3000, 3010, 3200, and 3210 Upgrading a CTS 3000 to a CTS 3200 Figure 6-79 displays the rear view of the Cisco TelePresence System. Left and right are reversed. Note Before you plug cables into a codec, label each cable.
  • Page 162 Step 6 Enter the required information at the login screen. The Cisco TelePresence Administrator window appears. Verify the status of the Cisco Unified Communications Manager (seen in the lower left portion of the Step 7 window) is Enabled/Up. Select Hardware Setup to verify the cameras, displays, speakers, and microphones are working Step 8 properly.
  • Page 163 Reflector Wall, page 7-2 Upgrading a TX9000 System to a TX9200 System You can upgrade an existing system from a TX9000 to a TX9200 by using the Cisco-provided upgrade kit. The part number for the upgrade kit is CTS-TX9200-UPG. To order this upgrade kit, contact Customer Service 1-800-553-6387. To complete the upgrade, perform...
  • Page 164 Chapter 7 Options for the Cisco TelePresence System TX9000 and TX9200 Converting a System with a Wall-Mounted Reflector Wall to a System with a Free-Standing Reflector Wall Converting a System with a Wall-Mounted Reflector Wall to a System with a Free-Standing Reflector Wall You can convert a system with a wall-mounted reflector wall to one with a Free-standing reflector wall.
  • Page 165 Chapter 7 Options for the Cisco TelePresence System TX9000 and TX9200 Converting a System with a Free-Standing Reflector Wall to a System with a Wall-Mounted Reflector Wall Save the panels and do not damage the panels when you remove them. Use gloves and moving blankets Caution when handling the panels.
  • Page 166 Chapter 7 Options for the Cisco TelePresence System TX9000 and TX9200 Converting a System with a Free-Standing Reflector Wall to a System with a Wall-Mounted Reflector Wall Cisco TelePresence System OL-16441-01...

This manual is also suitable for:

Telepresence system 1000Telepresence system 1300Telepresence system 3000Telepresence system 3010Telepresence system 3200Telepresence system 3210

Table of Contents