Panel; Recording - Toshiba D-VR17KB Owner's Manual

E9GA0BD_EN.book Page 35 Monday, March 26, 2007 10:25 AM
If the Timer Programming did not
Complete Correctly
The error number appears on the Timer Programming
list.
Timer Programming
Date Start
E40 06/12 7:00
New Program
The error programme will be displayed in grey
with an error number.
The error numbers indicate:
E1–E22,
E37–E39: Recording error
E23–E24: Unrecordable disc
E25 : • Copy prohibited programme
• Cannot record because of the NTSC /
PAL-60 signal is received.
E26–E28: Copy prohibited programme
E29 : Disc protected
E30 : Disc full
E31 : Already recorded 99 titles (Video
mode)
E32 : Already recorded 99 titles (VR mode)
E33 : Already recorded 999 chapters
E34 : No space for Control Information
E35 : PCA (Power Calibration Area) full
E36 : Already finalised Video format disc
E40 : • There are some unrecorded parts due
the overlapped timer programmes.
• Recording did not start at the start
time.
• There is no tape in the cassette
compartment.
• Tape recording reaches to the tape
end during timer recording.
E41 : Power failure
E42 : No disc
E43 : Already 49 titles recorded (+VR mode)
E44 : Already 254 chapters recorded (+VR mode)
E45 : Copy prohibited programme
E46 : It is impossible to record additionally on
a disc recorded by other units when
setting "Make Recording Compatible"
to "OFF". (+VR mode)
The error programme will be deleted once you
check the error in the programme list, or once you
cancel the timer-standby mode and re-enter it.
Hints for the Timer Recording
• If there is a power failure or the unit is unplugged for
more than 30 seconds, the clock setting and all
timer settings will be lost.
• If there is no disc or an unrecordable disc in the tray
(finalised DVD-RW/-R, finalised DVD+R, a fully
recorded disc, etc.), the DVD on the front panel
display will flash and the timer recording will not
occur. Insert a recordable disc.
0:00 THU 06/12
End CH PDC
9:00 P11
1/1
• If there is no tape or a tape with a record tab is not in
the cassette compartment, the VCR on the front
panel display will flash and the timer recording
cannot be performed. Please insert a recordable
tape.
• When all timer recordings are complete, the
icon flashes. To play back or eject the recorded disc,
press [TIMER SET], and then press [PLAY P] or
[OPEN / CLOSE O].
• The timer recording cannot be performed in DVD
and VCR at the same time. If you set two
programmings with the same channel and time both
in DVD and VCR, the programming that has priority
will be recorded.
• You cannot make any DVD operation during DVD
timer recording.
• You cannot make any VCR operation during VCR
timer recording.
• If the Start and End times are same, the length of
the recording will be set for 24 hours. If the disc or
tape becomes full during recording, the unit will turn
itself off. To continue recording, press [TIMER SET]
to cancel the timer-standby mode, insert a
recordable disc or tape and press [TIMER SET]
again.
• When 2 or more programmes are overlapped,
"Timer program overlapped" appears, and the
overlapped programme will be displayed in blue. To
correct the timer programme refer to "Checking,
Cancelling or Correcting the Timer Programming
Information" on page 34.
• If the Start time is earlier and the End time is later
than the current time, the recording will start
immediately after you press [TIMER SET].
• If a videotape ends during the timer recording, the
unit will automatically stop, eject the videotape, and
turn itself off. To continue recording, insert a
recordable tape.
Priority of overlapped settings
The unit records programmes according to priority if
the timer programmes overlap.
If the starting time is same:
• The timer programming set first (PROG. 1) has
priority.
PROG. 1
PROG. 2
Actual
PROG. 1

recording

The first 2 minutes (at the longest) will be cut off.
When the starting time and the ending time for
each programmes are different:
• A programme that has earlier start time has priority.
PROG. 1
PROG. 2
PROG. 3
Actual
PROG. 1
recording
The first 2 minutes (at the longest) will be cut off.
PROG. 2
recording
will start
after
PROG. 1
recording is
PROG. 2
completed.
PROG. 3
PROG. 2
35
EN