Page 1
Technical Manual Intel Bay Trail Series CPU Based Mini-ITX M/B NO.G03-NF9T-F Revision: 2.0 Release date: October 1, 2019 Trademark: * Specifications and Information contained in this documentation are furnished for information use only, and are subject to change at any time without notice, and should not be construed as a commitment by manufacturer.
Page 2
Environmental Protection Announcement Do not dispose this electronic device into the trash while discarding. To minimize pollution and ensure environment protection of mother earth, please recycle.
Environmental Safety Instruction Avoid the dusty, humidity and temperature extremes. Do not place the product in any area where it may become wet. 0 to 60 centigrade is the suitable temperature. (The figure comes from the request of the main chipset) ...
USER’S NOTICE COPYRIGHT OF THIS MANUAL BELONGS TO THE MANUFACTURER. NO PART OF THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT MAY BE REPRODUCED, TRANSMITTED OR TRANSLATED INTO ANY LANGUAGE IN ANY FORM OR BY ANY MEANS WITHOUT WRITTEN PERMISSION OF THE MANUFACTURER.
Chapter 1 Introduction of the Motherboard Feature of Motherboard ® Onboard Intel Bay Trail series processor, with low power consumption never denies high performance Support DDR3L SO-DIMM 1066/1333 MHz up to 8GB Support Mini-PCIE connector Support m-SATA connector ...
Specification Spec Description 6 layers; PCB size: 17x 17 cm Design ® Integrated with Intel Bay Trail-D/M/I series CPU Embedded CPU 1* DDR3L SODIMM Slot for un-buffered DDR3L 1066* Mhz or 1333* Mhz SDRAM, expandable to 8GB Memory Slot *Memory clock supporting range is decided by specific CPU of the model.
1* DC 12V internal power connector 1* SATA Power connector 1* CPU FAN connector 2* SYSFAN connector 1* Front panel audio header 1* SPDIF Out header 1* LAN LED activity header 1* SPEAK_CON header ...
Page 11
Jumper Jumper Name Description JP10(Pin 1-2) Disable ME Function Select 2-Pin Block JP10(Pin 3-4) CMOS RAM Clear Function Select 2-Pin Block JP10(Pin 5-6) AT Mode Function Select 2-Pin Block JP10(Pin 7-8) Case Open Message Display Function 2-Pin Block Clear ME RTC Function Setting 3-Pin Block SYSFAN_DET SYSFAN1/SYSFAN2 R.P.M.
Page 12
UL1(Top) RJ-45 LAN Port Connector UL1(Middle) USB 2.0 Port Connector UL1(Bottom) USB 3.0 Port Connector AUDIO(Top) Audio Line Out Connector AUDIO(Bottom) Audio MIC In Connector CPUFAN CPUFAN Connector SYSFAN1/SYSFAN2 SYSFAN Connector X2 Headers Header Name Description FP_AUDIO Front Panel Audio Header 9-pin Block SPDIF HDMI_SPDIF Out Header...
Chapter 2 Hardware Installation 2-1 Jumper Setting Pin 1-2 of JP10 (8-pin): Security Measure Function Select Pin 1-2 of JP10→ Disable ME Function Select Pin 1 1-2 Open: Normal; Pin 1 1-2 Closed: Disable ME Function Selected. Pin 3-4 of JP10 (8-pin): Clear CMOS Setting Pin 3-4 of JP10→...
Page 14
Pin 5-6 of JP10 (8-pin): AT Mode Function Select Pin 5-6 of JP10→ AT Mode Select Pin 5 5-6 Open: ATX Mode Selected; Pin 5 5-6 Closed: AT Mode Selected. *ATX Mode Selected: Press power button to power on after power input ready; AT Mode Selected: Directly power on as power input ready.
Page 15
Pin 7-8 Closed: When Case open function pin short to GND, the Case open function was detected. When Used, needs to enter BIOS and enable ‘Case Open Detect’ function. In this case if your case is removed, next time when you restart your computer, a message will be displayed on screen to inform you of this.
Page 20
User can select Panel resolution by jumper settings. There are two basic setting modes: Short: in which user can close pin 1-pin2, pin3-pin4, pin5-pin6, pin7-pin8 respectively; Open: in which user leave jumper hat just in pin 2, pin4, pin6 or pin8. Option Jumper Setting Description...
Page 21
Pin 1-2: Short Pin 3-4: Short 1366 x 768 @ 60Hz 24-bit Pin 5-6: Short Pin 7-8: Open Pin 1-2: Open Pin 3-4: Short 1440 x 900 @ 60Hz 24-bit Pin 5-6: Short Pin 7-8: Open Pin 1-2: Short Pin 3-4: Open 1280 x 1024 @ 60Hz 24-bit...
Connectors and Headers 2-2-1 Connectors (1) Rear I/O Connectors PS/2 KB & MS Port Parallel Port RJ-45 LAN Port COM1 Port USB 2.0 Port Line-Out Port MIC Port DC Power-in Connector VGA Port COM2 Port HDMI Port USB 2.0 Ports USB 3.0 Port (2) COM1 (9-pin Block): RS232/422/485 Port COM1 port can function as RS232/422/485 port.
Page 23
(3) J1 (2-pin Block): DC12V Power-in Connector (4) SATA1/SATA2(7-pin Block): SATAII Port connector These are high-speed SATAII ports that support 3GB/s transfer rate. Pin No. Definition * Note: SATA2 shares with MSATA.
Page 24
(5) SATAPW (4-pin): SATA Power Connector Pin 1 (6) CPUFAN/SYSFAN1/SYSFAN2 (4-pin): Fan Connectors Definition +12V Fan Power Fan Speed Control...
Chapter 3 Introducing BIOS Notice! The BIOS options in this manual are for reference only. Different configurations may lead to difference in BIOS screen and BIOS screens in manuals are usually the first BIOS version when the board is released and may be different from your purchased motherboard. Users are welcome to download the latest BIOS version form our official website.
BIOS Menu Screen The following diagram show a general BIOS menu screen: Menu Bar General Help Items Current Setting Value Function Keys Menu Items BIOS Menu Screen Function Keys In the above BIOS Setup main menu of, you can see several options. We will explain these options step by step in the following pages of this chapter, but let us first see a short description of the function keys you may use here: ...
Press ↑↓ (up, down) to choose, in the main menu, the option you want to confirm or to modify. Press <Enter> to select. Press <+>/<–> keys when you want to modify the BIOS parameters for the active option.
User can press the right or left arrow key on the keyboard to switch from menu bar. The selected one is highlighted. Main Menu Main menu screen includes some basic system information. Highlight the item and then use the <+> or <-> and numerical keyboard keys to select the value you want in each item.
3-7 Advanced Menu ERP Function The optional settings: [Disabled]; [Auto]. This item should be set as [Disabled] if you wish to have all active wake-up functions. OS Selection The optional settings: [Android]; [Windows 8.X]; [Windows 7]. *Note: User needs to go to this item to select OS before installing OS. If Windows Embedded standard 8, Please select [Windows 8x] and set “USB 3.0 Support”...
Page 37
ACPI Settings Press [Enter] to make settings for the following sub-item: ACPI Settings ACPI Sleep State Use this item to select the highest ACPI sleep state the system will enter when the suspend button is pressed. The optional settings are: [Suspend Disabled]; [S3 (Suspend to RAM)]. ...
Page 38
Serial Port FIF0 Mode The optional settings are: [16-Byte FIF0]; [32-Byte FIF0]; [64-Byte FIF0]; [128-Byte FIF0]. Serial Port 2 Configuration/ Serial Port 3 Configuration/ Serial Port 4 Configuration/ Serial Port 5 Configuration Press [Enter] to make settings for the following items: Serial Port Use this item to enable or disable serial port (COM).
Page 39
WatchDog Wake-up Timer in ERP This item support WDT wake-up while ERP function is set as [Auto]. The optional settings are: [Enabled]; [Disabled]. When set as [Enabled], the following sub-items shall appear: WatchDog Timer Value in ERP User can set a value in the range of 10 to 4095. WatchDog Timer Unit The optional settings are: [Sec.];...
Page 40
CPUFAN / SYSFAN1/2 Idle-Speed Temperature Use this item to set CPUFAN/SYSFAN1/2 idle speed temperature. Fan will run at idle speed when below this temperature. CPUFAN / SYSFAN1/2 Idle-Speed Duty Use this item to set CPUFAN/SYSFAN1/2 idle speed duty.. Fan will run at idle speed when below the pre-set duty.
Page 41
The optional settings are: [None]; [Even]; [Odd];[Mark]; [Space]. Stop Bits The optional settings are: [1]; [2]. Flow Control The optional settings are: [None]; [Hardware RTS/CTS]. VT-UTF8 Combo Key Support The optional settings are: [Disabled]; [Enabled]. Recorder Mode The optional settings are: [Disabled]; [Enabled]. Resolution 100x31 The optional settings are: [Disabled];...
Page 42
*This item may or may not show up, depending on different configuration. Terminal Type The optional settings are: [VT100]; [VT100+];[VT-UTF8];[ANSI]. Bits per second The optional settings are: [9600]; [19200]; [57600]; [115200]. Flow Control The optional settings are: [None]; [Hardware RTS/CTS]; [Software Xon/Xoff]. Data Bits The default setting is: [8].
Page 43
The optional settings: [Disabled]; [Enabled]. When set as [Enabled], a VMM can utilize the additional hardware capabilities provided by Vanderpool Technology. Power Technology The optional settings: [Disabled]; [Energy Efficient]. PPM Configuration Press [Enter] to make settings for PPM Configuration: PPM Configuration: EIST The optional settings: [Disabled];...
Page 44
The optional settings are: [Port1 ODD]; [Port2 ODD]; [No ODD]. SATA Port1 The optional settings are: [Enabled]; [Disabled]. SATA Port2 The optional settings are: [Enabled]; [Disabled]. Network Stack Configuration Press [Enter] to go to ‘Network Stack’ screen to make further settings. Network Stack The optional settings are: [Enabled];...
Page 45
Storage This item controls the execution of UEFI and Legacy Storage OpROM. The optional settings are: [Do not launch]; [UEFI only]; [Legacy only]; [Legacy first]; [UEFI first]. Other PCI devices This item determines OpROM execution policy for devices other than Network, storage or video.
Page 46
Use this item to set USB mass storage device start unit command time-out. The optional settings are: [10 sec]; [20 sec]; [30 sec]; [40 sec]. Device power-up delay Use this item to set maximum time the device will take before it properly reports itself to the host controller.
information. 3-8 Chipset Menu North Bridge Press [Enter] to view current using memory information and make settings for the following sub-items: Intel IGD Configuration IGD Turbo Enable The optional settings are: [Enabled]; [Disabled]. Spread Spectrum Clock The optional settings are: [Enabled]; [Disabled].
Page 48
IGD Boot Type Use this item to select preference display interface used when system boot. The optional settings are: [Auto]; [CRT]; [HDMI]; [LVDS]. * Note: User needs to set ‘Active LFP’ as [Enabled], otherwise the optional setting [LVDS] will not be available. Active LFP The optional settings are: [Disabled];...
Page 49
USB 3.0 Link Power Management The optional settings are: [Enabled]; [Disabled]. * Note: This item only show up when ‘USB 3.0 Support’ set as [Enabled], [Auto] or [Smart Auto]. USB 2.0 Support The optional settings are: [Auto]; [Disabled]. * Note:When set as [Auto], user can make further settings in the following sub-items: USB RMH Mode The optional settings are: [Enabled];...
3-10 Boot Menu Boot Configuration Setup Prompt Timeout Use this item to set number of seconds to wait for setup activation key. Bootup Numlock State Use this item to select keyboard numlock state. The optional settings are: [On]; [Off]. Quiet Boot The optional settings are: [Disabled];...
Boot Option The optional settings are: [UEFI: Built-in EFI Shell]; [Disabled]. 3-11 Save & Exit Menu Save Changes and Reset This item allows user to reset the system after saving the changes. Discard Changes and Reset This item allows user to reset the system without saving any changes. Restore Defaults Use this item to restore /load default values for all the setup options.
Page 53
Save as User Defaults Use this item to save the changes done so far as user defaults. Restore User Defaults Use this item to restore defaults to all the setup options. Boot Override UEFT: Built-in EFI Shell Launch Internal EFI shell application (shell.efi). Lauch EFI Shell from filesystem device Use this item to launch EFI shell application (shell.efi) from one of the available filesystem device.